Outboard Lock - OMC (40hp+), 1/2" x 13 thread from MCGARD
Help make your outboard less attractive to thieves, and also keep it from vibrating loose while running. The vinyl-clad steel tube slides over the mounting screws and is secured with a hardened brass padlock. Padlock is recessed inside the tube to protect against cutting. Comes with two keys. *Fits: OMC 6-30hp, Merc/Mariner 8-25hp, Yamaha 9. 9-40hp, Suzuki 8-13hp.
$31.99
|
Outboard Lock - Yam/Suz/Other*, 5/16" x 18 thread from MCGARD
Help make your outboard less attractive to thieves, and also keep it from vibrating loose while running. The vinyl-clad steel tube slides over the mounting screws and is secured with a hardened brass padlock. Padlock is recessed inside the tube to protect against cutting. Comes with two keys. *Fits: OMC 6-30hp, Merc/Mariner 8-25hp, Yamaha 9. 9-40hp, Suzuki 8-13hp.
$31.99
|
1" Outlet 1, 1" Outlet 2 from MARINE EAST
Unique Design Drains Faster, While Eliminating As Many As Two Unsightly Thru-Hulls Innovative design generates vortex action for faster drainage . 1-1/2" Hose barb at top end with 1 1/2" NPT threads OR barb at bottom. . Side barbs available from 5/8" to 1-1/8" in all combinations . Saves labor and parts . Molded in high-impact super-tough Nylon (S. T. 801) .
$21.99
|
3/4" Outlet 1, 1-1/8" Outlet 2 from MARINE EAST
Unique Design Drains Faster, While Eliminating As Many As Two Unsightly Thru-Hulls Innovative design generates vortex action for faster drainage . 1-1/2" Hose barb at top end with 1 1/2" NPT threads OR barb at bottom. . Side barbs available from 5/8" to 1-1/8" in all combinations . Saves labor and parts . Molded in high-impact super-tough Nylon (S. T. 801) .
$21.99
|
5/8" Outlet 1, 3/4" Outlet 2 from MARINE EAST
Unique Design Drains Faster, While Eliminating As Many As Two Unsightly Thru-Hulls Innovative design generates vortex action for faster drainage . 1-1/2" Hose barb at top end with 1 1/2" NPT threads OR barb at bottom. . Side barbs available from 5/8" to 1-1/8" in all combinations . Saves labor and parts . Molded in high-impact super-tough Nylon (S. T. 801) .
$21.99
|
High Security Outboard Lock from WEST MARINE
Polished 316 Stainless Steel high security key locks with anti-drill protection secure outboards to your boat. Bolt Lock model’s backing plate installs under engine transom nut and fits up to 1/2" engine bolts. Bar Lock model fits most outboard engines with turnbuckle installations. Noise dampeners reduce rattle.
$99.99
|
Closed-Base Cleats - Chromed Zinc 4 1/2", Plastic Base from PERKO
We stock a complete selection of cleats for anchoring, docking and general-purpose use. Zinc cleats should be used in fresh water only. Fasteners not included. 4 1/2" long. Requires four #10 FHMS fasteners.
$24.99
|
Open-Based Cleats - Chromed Zinc, Plastic Base 4 1/2" from PERKO
We stock a complete selection of cleats for anchoring, docking and general-purpose use. Zinc cleats should be used in fresh water only. Fasteners not included. 4 1/2" long. Requires four #10 FHMS fasteners.
$22.99
|
Outboard Bolt On Lock from WEST MARINE
Polished 316 Stainless Steel high security key locks with anti-drill protection secure outboards to your boat. Bolt Lock model’s backing plate installs under engine transom nut and fits up to 1/2" engine bolts. Bar Lock model fits most outboard engines with turnbuckle installations. Noise dampeners reduce rattle.
$49.99
|
Seal for Wire OD 0.24–0.47", 1/2" NPT, Gauges 20, 18, 16, 14, 12, 10, 8, 6, 2, 1 from ANCOR MARINE
Wire Seal allows you to run wire through a surface using a waterproof, strain-relieving seal. The clamping mechanism works like a compression nut or packing gland. As the outer nut is tightened, a seal on the inside contracts about the wire (or tubing) that runs through it. The Wire Seal inserts into the surface and uses a 1/2"NPT thread nut on the other side (like conduit nuts). Offers sealing solutions for a wide range of wire sizes, including round, flat, duplex and triplex wires.
$14.99
|
Open-Based Cleats - Chromed Zinc, Plastic Base 6" from PERKO
We stock a complete selection of cleats for anchoring, docking and general-purpose use. Zinc cleats should be used in fresh water only. Fasteners not included. 4 1/2" long. Requires four #10 FHMS fasteners.
$19.99
|
