High-Build Yellow Primer - Quart from STERLING
Corrosion-resistant primer for heavy aluminum plate and blasted steel. Can be topcoated after 220-grit sanding. Mix 1:1 with U-4748 catalyst and thin as needed with U-1289. When applied by roller or spray, will build to about 15mm per coat. Mixed quart covers about 25 sq.
$99.99
|
Skip Sand Primer, Qt from PETTIT
Recommended for use over vinylester and other blister-resistant gelcoats where sanding is forbidden, this primer eliminates the need to sand prior to application of antifouling paint. It may also be used over conventional gelcoats and as a tie-coat between two-part epoxy primers and antifouling paints. Quart. Color: Green/Silver. Drying time: To touch: 1hr. @ 70°F. ; to overcoat: 2hrs.
$33.99
|
No-Sand Primer from INTERLUX
Speeds up the prepping process prior to application of antifouling paint Eliminates the need to sand fiberglass boats before painting by creating a chemical bond between the fiberglass surface and the first coat of antifouling paint. Quart. Primary Usage: Underwater, bare fiberglass, as tie-coat for bottom paint . Formulation: Underwater fiberglass primer for bottom paint. Applies Over: De-waxed bare fiberglass. to 2 hrs. Number of Coats Recommended: One coat, applied in one direction only.
$43.99
|
Aluma Protect from PETTIT
Very good as a primer for aluminumTwo-part strontium-chromate primer, mostly used to prime aluminum prior to application of antifouling paint. Can also be used on aluminum as a primer for Easypoxy or ZSpar enamels. Primary Usage: Aluminum hulls, outboard and outdrive lower units . Formulation: Two-part epoxy anti-corrosive aluminum primer . Drying Time: Pot life: 16-20 hrs. ; to recoat: 1-8 hrs. . Number of Coats Recommended: Two . Thinner: Use Pettit 120 for clean-up . Coverage: 106 sq.
$64.99
|
InterProtect Epoxy 3000/1 Barrier Coat - Gallon Kit from INTERLUX
Microplates® act like shingles to prevent water absorptionHigh solids, VOC compliant epoxy with Microplates®. Can be used down to 32°F. Use Interprotect® 2000E as tie coat prior to the application of antifouling paint. Total Thickness Required: 10mil dry (3-4 coats) Drying Time: To touch 1-16hrs. ; overcoating: 1 1/2hrs. - 3 months @ 32°-95°F. Coverage: Brush: 82sq. ft. /qt. , 330sq. ft.
$134.99
|
Hullgard Expoxy Primer, Buff from AWLGRIP
Hullgard Epoxy Primer is a holding primer that combines excellent anticorrosion and water barrier properties with anti-fouling tie-coat functionality. Suitable for below the waterline only, it offers a long overcoating interval without sanding to reduce work time along with superb adhesion to properly prepared fiberglass, steel, aluminum and wood. Can be recoated as soon as the solvents evaporate, even at low temperatures. 1 Gal. Theoretical Coverage – 140 Sq. 5 mils/135 microns DFT or 360 Sq.
$114.99
|
Hullgard Primer Converter, Qt. from AWLGRIP
Hullgard Epoxy Primer is a holding primer that combines excellent anticorrosion and water barrier properties with anti-fouling tie-coat functionality. Suitable for below the waterline only, it offers a long overcoating interval without sanding to reduce work time along with superb adhesion to properly prepared fiberglass, steel, aluminum and wood. Can be recoated as soon as the solvents evaporate, even at low temperatures. 1 Gal. Theoretical Coverage – 140 Sq. 5 mils/135 microns DFT or 360 Sq.
$35.99
|
6455 Metal Primer - Quart from PETTIT
Provides corrosion and rust-resistance on steel or aluminum. A corrosion-inhibiting pigment keeps the metal surface in good condition and enhances adhesion to metal of primers and topcoats applied over it. Not recommended for wood or fiberglass. Drying, Overcoat: 2-24 hours Thinner: Denatured alcohol Coverage: 400-600 sq. ft. /gal.
$52.99
|
404/414 Epoxy Primer - Quart Kit from INTERLUX
Versitile primer for all topside finishesMultipurpose, two-part epoxy primer for use above or below the waterline. Good enamel holdout, sands freely but does not sand through easily, and provides an excellent base for all topside finishes. Resurfaces cracked gel coat prior to application of enamel. Recommended Usage: Above water, primer for Perfection two-part, sanding surfacer for cracked/crazed gelcoat. Formulation: Multi-purpose two-part epoxy primer. Coverage: Brush: 112sq. ft/qt, 450sq.
$43.99
|
Vinyl-Lux® Primewash from INTERLUX
Self-etching primer promotes adhesion of paint to metal Promotes adhesion of paint to metal. Two-part zinc chromate, vinyl butyral self-etching primer. Must be thinned with Interlux 355 Thinner. Do not apply more than one coat. Two-part kit makes one quart. Primary Usage: Metal conditioner prior to application of other paints . Formulation: Self-etching two-part zinc- chromate vinyl butyral. Applies Over: Clean bare metal. Drying Time: To touch: 30 min; to overcoat: window of 1 to 24 hrs.
$74.99
|
Two-Part Pour Foam Kit - 2 Quarts from EVERCOAT
Excellent for creating icebox insulation Two-quart kit mixes in 1:1 ratio. Use for adding icebox or sound deadening insulation and additional flotation. Expands to 2cu. ft. or 25 times its volume. Create or add to existing flotation. Improve your ice boxes insulation.
$99.99
|
