Pedestal Guard

Teak Steering Cockpit Table - Drop Leaf, Pedestal-Mount, 9 1/2" from EDSON CORPORATION
Formed wire brackets hold the table in the up position Solid teak tables to turn your cockpit into an entertainment center Clips secure the table to your pedestal guard in the down position Drop Leaf Tables Dimensions-- Open: 27” x 26”, Closed: 27” x 13” Luncheon Tables Dimensions: 13 1/2” x 24”.
$999.00

Stainless-Steel GPS Mounting Arm from EDSON CORPORATION
Pre-drilled to fit the Garmin 45 mounting bracket; also accepts most other round GPS brackets up to 3" (76mm) Arm designed to attach to all 1" & 1-1/4" pedestal guard tubes without removing tubes or existing wiring .
$159.99

Guard Feet Kit from EDSON CORPORATION
Stainless guard feet secure the guard to the cockpit sole. Fits existing mounting position as original black plastic feet. Kit includes two feet, deck guards, bolts, set screws and bushings.
$69.99

Pedestal Maintenance Kit from EDSON CORPORATION
Three kits: Maintenance Kit includes two snap rings, two spare shaft keys, a 1/2oz. tube of white Teflon lubricant and Loctite 242. Rebuild Kit includes snap rings (2), shaft keys (3), needle bearing sets (2), nylon washers, an O-ring, Locktite 242, a white Teflon lubricant, and a complete Pedestal Maintenance Guide.
$54.1 $48.99

Pedestal Brake Kit from EDSON CORPORATION
Three kits: Maintenance Kit includes two snap rings, two spare shaft keys, a 1/2oz. tube of white Teflon lubricant and Loctite 242. Rebuild Kit includes snap rings (2), shaft keys (3), needle bearing sets (2), nylon washers, an O-ring, Locktite 242, a white Teflon lubricant, and a complete Pedestal Maintenance Guide.
$59.99

Pedestal Rebuild Kit from EDSON CORPORATION
Three kits: Maintenance Kit includes two snap rings, two spare shaft keys, a 1/2oz. tube of white Teflon lubricant and Loctite 242. Rebuild Kit includes snap rings (2), shaft keys (3), needle bearing sets (2), nylon washers, an O-ring, Locktite 242, a white Teflon lubricant, and a complete Pedestal Maintenance Guide.
$64.99 $59.88

Stainless-Steel Brake Knob from EDSON CORPORATION
Stainless steel knob for Edson wheel brake For Edson wheel pedestal brakes, a highly-polished, stainless-steel brake knob to directly replace Edson’s plastic model.
$77.99

Pedestal Steering Brake from EDSON CORPORATION
Especially handy on long runs or when operating under power, this brake can secure the wheel under most conditions and will hold the boat on course while the helmsman trims a sheet or goes below. The brake can always be overridden by the helmsman. Constructed of bronze with long-lasting linings, includes a stainless shaft and brake knob. For safety, the handle is designed to pop off if a line is tangled around it. Pre-drilled holes allow installation in about 20 minutes.
$192.99

Control Handle - Throttle 963SB-55 from EDSON CORPORATION
Highly polished, investment cast stainless steel, marked "Fast-Slow" and "Fwd-Rev". Designed to fit Edson Dual Lever Engine Controls.
$72.99

Control Handle - Clutch 863PT-55 from EDSON CORPORATION
Highly polished, investment cast stainless steel, marked "Fast-Slow" and "Fwd-Rev". Designed to fit Edson Dual Lever Engine Controls.
$72.99

Standard 3/4" Wheel Nut from EDSON CORPORATION
Necessary to fix a destroyer wheel on your existing wheel shaft. Standard model is a polished stainless hexagonal nut. Quick Release model is a 2" dia. cast stainless knurled knob, which can be removed by hand. Fit Edson standard shafts (1"-14), except 303884, which fits 3/4"-10 shafts. Each ShWt 0.
$54.99