Safety Seacock Converters

Safety Seacock Conversion, 1-1/4" Thread NPT, 1-1/4" Hose ID from GROCO
Screws into the top of any seacock and turns it into a safety seacock. The quick-release plug enables simple cooling system flushing, winterization, and draining.
$94.99

Safety Seacock Conversion, 1" Thread NPT, 1" Hose ID from GROCO
Screws into the top of any seacock and turns it into a safety seacock. The quick-release plug enables simple cooling system flushing, winterization, and draining.
$84.99

Safety Seacock Conversion, 2" Thread NPT, 2" Hose ID from GROCO
Screws into the top of any seacock and turns it into a safety seacock. The quick-release plug enables simple cooling system flushing, winterization, and draining.
$129.99

Safety Seacock Conversion, 3/4" Thread NPT, 3/4" Hose ID from GROCO
Screws into the top of any seacock and turns it into a safety seacock. The quick-release plug enables simple cooling system flushing, winterization, and draining.
$69.99

Seacock, 2" Inlet (NPS), 2" Discharge (NPT), 1-1/2" Side (NPT) from GROCO
With NPT-threaded side port for permanent installation of an in-line ball valve or other threaded component. Enables engine to function as a bilge pump in an emergency. Handle may be relocated to either side of the valve body. 316 stainless-steel ball and stem.
$474.99

Seacock, 1-1/2" Inlet (NPS), 1-1/2" Discharge (NPT), 1-1/4" Side (NPT) from GROCO
With NPT-threaded side port for permanent installation of an in-line ball valve or other threaded component. Enables engine to function as a bilge pump in an emergency. Handle may be relocated to either side of the valve body. 316 stainless-steel ball and stem.
$394.99

1-1/2" NPT Threaded Pneumatic Tank Sender from FIREBOY XINTEX, INC.
PTS Senders (threaded): 1-1/2" NPT threaded pneumatic tank sender, 12" for freshwater and holding tanks PFS Senders (flanged, standard 5 bolt pattern): 5-Hole flanged pneumatic tank sender, 12" for freshwater and holding tanks Pneumatic LLM-2 Owners Manual and Installation Instructions.
$99.99

Seal for Wire OD 0.24–0.47", 1/2" NPT, Gauges 20, 18, 16, 14, 12, 10, 8, 6, 2, 1 from ANCOR MARINE
Wire Seal allows you to run wire through a surface using a waterproof, strain-relieving seal. The clamping mechanism works like a compression nut or packing gland. As the outer nut is tightened, a seal on the inside contracts about the wire (or tubing) that runs through it. The Wire Seal inserts into the surface and uses a 1/2"NPT thread nut on the other side (like conduit nuts). Offers sealing solutions for a wide range of wire sizes, including round, flat, duplex and triplex wires.
$14.99

Diver's Dream Anode 1/2" x 6 x 12, w/1/2" Slot from SEA SHIELD
ZHC Diver's Dream Anode. All zinc anodes conform to Mil-a-18001 1/2" thick. 6" wide. 12" length. 8. 5 lb. s.
$64.99

Seal for Wire OD 0.24–0.55", Gauges #4, 3, 2, 1, 14/2, 12/2, 10/2, 14/3, 12/3 from ANCOR MARINE
Wire Seal allows you to run wire through a surface using a waterproof, strain-relieving seal. The clamping mechanism works like a compression nut or packing gland. As the outer nut is tightened, a seal on the inside contracts about the wire (or tubing) that runs through it. The Wire Seal inserts into the surface and uses a 1/2"NPT thread nut on the other side (like conduit nuts). Offers sealing solutions for a wide range of wire sizes, including round, flat, duplex and triplex wires.
$13.99

Seacock, 1-1/4" Inlet (NPS), 1-1/4" Discharge (NPT), 1" Side (NPT) from GROCO
With NPT-threaded side port for permanent installation of an in-line ball valve or other threaded component. Enables engine to function as a bilge pump in an emergency. Handle may be relocated to either side of the valve body. 316 stainless-steel ball and stem.
$294.99