Seal Assembly from JABSCO
NOTE: Conversion to Twist’n’Lock operation requires installation of complete Pump Assembly (29040-3000) or Piston, Rod, O-Ring Assembly (29046-3000) and Valve Cover Assembly (29094-3000).
$16.49
|
500gph 12V Bilge Pump, 1.9A Draw at 12V DC, 3/4" Port, 4"H x 2-3/8"W from RULE INDUSTRIES
An internal computer chip cycles these pumps on every 2. 5 minutes, then quickly shuts them down if no water is detected. Built-in strainer bases snap off to make cleaning easy. Completely submersible, rust-proof, corrosion-proof and ignition-protected. Three-way wiring enables connection to a switch for manual override or indicator light. Small 500gph pump is designed to handle spray and rainwater. Built-In Switch: Yes, cycles every 2. 5 min.
$41.99
|
1100gph 12V Bilge Pump, 3.3A Draw at 12V DC, 1-1/8" Port, 4-1/2"H x 2-3/8"W from RULE INDUSTRIES
An internal computer chip cycles these pumps on every 2. 5 minutes, then quickly shuts them down if no water is detected. Built-in strainer bases snap off to make cleaning easy. Completely submersible, rust-proof, corrosion-proof and ignition-protected. Three-way wiring enables connection to a switch for manual override or indicator light. Small 500gph pump is designed to handle spray and rainwater. Built-In Switch: Yes, cycles every 2. 5 min.
$69.99
|
Replacement Motor, 12V for 37010 Series Electric Head from JABSCO
NOTE: Conversion to Twist’n’Lock operation requires installation of complete Pump Assembly (29040-3000) or Piston, Rod, O-Ring Assembly (29046-3000) and Valve Cover Assembly (29094-3000).
$149.99
|
Motor Cover, 37010 Head from JABSCO
NOTE: Conversion to Twist’n’Lock operation requires installation of complete Pump Assembly (29040-3000) or Piston, Rod, O-Ring Assembly (29046-3000) and Valve Cover Assembly (29094-3000).
|
Toilet Pump Assembly Kit (12-Volt) from JABSCO
Jabsco 37072-0092 Marine Designer Series and Quiet Flush Marine Toilet Pump Assembly Kit (12-Volt).
$144.99
|
Bowl Gasket, 37010 Head from JABSCO
NOTE: Conversion to Twist’n’Lock operation requires installation of complete Pump Assembly (29040-3000) or Piston, Rod, O-Ring Assembly (29046-3000) and Valve Cover Assembly (29094-3000).
$14.49
|
Macerator Housing, 37010 Head from JABSCO
NOTE: Conversion to Twist’n’Lock operation requires installation of complete Pump Assembly (29040-3000) or Piston, Rod, O-Ring Assembly (29046-3000) and Valve Cover Assembly (29094-3000).
$26.99
|
Cylinder Assembly (All Years) from JABSCO
NOTE: Conversion to Twist’n’Lock operation requires installation of complete Pump Assembly (29040-3000) or Piston, Rod, O-Ring Assembly (29046-3000) and Valve Cover Assembly (29094-3000).
$57.99
|
Jabsco Spud/Intake Elbow and O-Ring from JABSCO
NOTE: Conversion to Twist’n’Lock operation requires installation of complete Pump Assembly (29040-3000) or Piston, Rod, O-Ring Assembly (29046-3000) and Valve Cover Assembly (29094-3000).
$29.99
|
12V Macertor Pump, 16A Draw from JABSCO
Now featuring a sealed design, these pumps include run dry protection with a self-priming flexible impeller and stainless-steel wear plate. Self-priming to 5' when wet and grinds waste to 1/8" or smaller. Pumps 12gpm. The inlet port has a 1 1/2" hose barb combined with 1 1/2" male thread to screw directly onto a tank flange. Use 1"–1 1/2" hose adapter (Model 3274123) for 1 1/2" sanitation hose. Material: Nylon body, nitrile impeller, stainless steel wear plate .
$149.99
|
