4000gph Pump, 1-1/2" & 2" Port Sizes, 15A @ 12V DC, 8-1/2"H x 4-3/4"dia. from JOHNSON PUMPS
Designed to meet and exceed the tough demands of commercial and recreational duty, these pumps feature a 12-pole motor with double ball bearings for extended service life. 2200 and 4000 GPH models incorporate a mechanical seal design that eliminates shaft wear. Outlet port check valve included for optional use. Features: Double ball-bearing motors for extended service life . Type: Submersible centrifugal electric bilge pump . Port Sizes: 1-1/8"–2" . Built-In Switch: No .

1600gph Pump, 1-1/8" & 2" Port Sizes, 7A @ 12V DC, 5-7/8"H x 4-1/4"dia. from JOHNSON PUMPS
Designed to meet and exceed the tough demands of commercial and recreational duty, these pumps feature a 12-pole motor with double ball bearings for extended service life. 2200 and 4000 GPH models incorporate a mechanical seal design that eliminates shaft wear. Outlet port check valve included for optional use. Features: Double ball-bearing motors for extended service life . Type: Submersible centrifugal electric bilge pump . Port Sizes: 1-1/8"–2" . Built-In Switch: No .

2200gph Pump, 1-1/8" & 1-1/4" Port Sizes, 8.6A @ 12V DC, 7"H x 4-1/4"dia. from JOHNSON PUMPS
Designed to meet and exceed the tough demands of commercial and recreational duty, these pumps feature a 12-pole motor with double ball bearings for extended service life. 2200 and 4000 GPH models incorporate a mechanical seal design that eliminates shaft wear. Outlet port check valve included for optional use. Features: Double ball-bearing motors for extended service life . Type: Submersible centrifugal electric bilge pump . Port Sizes: 1-1/8"–2" . Built-In Switch: No .

Upper Pintle, 1-1/2" Rudder Thickness, 3-3/8" Strap Length, 1" Strap Width, 1-3/4" Pin Length from SCHAEFER
Typical installations use one with a short pin and one with a long pin. Pin diameter: 1/2". All require #10 RHMS.

1.05qt. (1 litre) Accumulator Tank, 13.25"L x 4.75"W x 4.38"H from JABSCO
Made of non-corrosive plastic, these tanks have an internal pressurized bladder which reduces pulsation and rapid on/off pump cycling. Bladders are pre-pressurized and their pressure can be adjusted with a standard bicycle pump. Tanks mount in any position. Include convenient Snap-Fit fittings. Material: Plastic with rubber bladder . Port Sizes: Includes four Snap-Fit port fittings: Two for 1/2" hose; Two for 1/2" Qest thread. Maximum Pressure: 125psi .

1100gph Automatic Bilge Pump, 3.4A @ 12V DC Draw, 1-1/8" Port from ATTWOOD
Engineered for extended service life, these pumps feature a cool-running design and quality components including permanent magnet motors, stainless steel shafts, and steel-reinforced seals. Type: Automatic centrifugal submersible . Features: Superior motor cooling. Test knob for operational check without disassembly. . Built-In Switch: Non-mercury mechanical float switch . Material: Glass-filled polyester impeller, 316 stainless shaft . 4"H x 3-1/4"W x 5-1/2" L.

52gal. Flexible Water Tank, 27-1/2" x 68-1/4" from PLASTIMO
Flexible, light and form-fitting, these tanks use a PVC bladder inside a tough, abrasion-resistant nylon outer “envelope. ” Maintenance is easy because the inner bladder can be removed for cleaning and inspection. The bladder is slightly oversized so pressure is exerted on its nylon shell, rather than on the heat-welded seams. 1 1/2" 90° fill and 1/2" straight outlet fittings ready to install. Port Sizes: 1-1/2" 90° fill, 1/2" straight outlet . Vent: No .

PV7D Controller, 1-1/2"W x 2-7/8"H x 1"D from FLEXCHARGE
Ultra -High Efficiency Solar & Wind Charge Controllers Waterproof and better than 99. 5% efficient with charging currents of 0. 5 to 25 amps, a 2-15% gain over competitors. Handles spikes up to 1,500V/A, so your controller won’t be damaged by surges. 7 amp PV7D is a cost effective shunting regulator for smaller 6V, 12V or 24V solar only applications, expandable to handle charging currents from 30 to 500A. Reverse polarity protected and fully sealed for use in high humidity environments.

Complete Double Braid Splicing Kit from SAMSON ROPE
Includes everything you need to make a smooth splice in double braid: tubular fids for 1/4", 5/16", 3/8", 7/16" and 1/2" line, a pusher and complete instructions. Fids and pusher are also sold separately.

Antenna Extention - 4FT Wht Polycarbonate from SHAKESPEARE ELECTRON
Raise the antenna height above interference for greater rangeLight-duty fiberglass extensions raise antennas above potential interference from backstays or pulpits. Mounts between your antenna base and your VHF antenna or loran coupler. 1" male and female threads on ends. We recommend the use of an upper support bracket when used with VHF antennas or on fast powerboats.

44lb. Galvanized-Manganese, 40'–58'L Boat, 34-1/2"L x 15-3/8"W x 15-1/4"H from LEWMAR
Easy handling, self-launching design sets fast in any seabed One-piece anchor has very high holding power and structural strength. Balanced to fall unaided from bow rollers, so it’s ideal for use with remotely operated windlasses. Heavy ballast in the toe section ensures that the anchor will engage the seabed upon hitting bottom. Lifetime warranty against breakage. Style: Non-Hinged Plow. Material: Galvanized-manganese steel or stainless steel. Application: All bottoms .

16-LED White/Task from WEST MARINE
These bright white LED lights are extremely energy-efficient and can be recess-mounted inside or out with a fully potted LED array board for total moisture resistance. And because they don't use bulbs with filaments, you won't have the cost of replacing them. Includes a chrome-finish bezel for a styled look. Light Style: Recessed accent . Voltage/Draw: 12V DC/0. 08A (16-LED: 0. 15A) . Bulb Wattage: 0. 96W; 16-LED consumes 1. 8W . Fixture Dimensions: 3-5/8" dia.

Poly Rod Rack - 4 Rod from WEST MARINE
High-density polyethylene racks, guaranteed for life. For vertical or overhead mounting. Mounting feet and stainless steel screws are included. Sold in pairs. 2-Rod Rack: 8-1/2"L x 2-7/8"H x 3/4"D. 4-Rod Rack: 15-1/2"L x 2-7/8"H x 3/4"D.

Stainless Steel Ultimate Fastener Kit from FASCO FASTENERS
Large quantities make the Ultimate Stainless Steel Fastener kit unique!A very comprehensive selection of the most popular Stainless Steel fasteners, including 8, 10 & 1/4" diameter machine screws up to 2" in length with nuts, nylocks & washers. 10 - 8/32 x 3/4 Phillips Oval Machine Screw . 10 - 8/32 x 1 Phillips Oval Machine Screw . 10 - 8/32 x 1-1/2 Phillips Oval Machine Screw . 10 - 10/24 x 3/4 Phillips Oval Machine Screw . 10 - 10/24 x 1-1/2 Phillips Oval Machine Screw .

Poly Rod Holder - 6 Rod from WEST MARINE
High-density polyethylene racks, guaranteed for life. For vertical or overhead mounting. Mounting feet and stainless steel screws are included. Sold in pairs. 2-Rod Rack: 8-1/2"L x 2-7/8"H x 3/4"D. 4-Rod Rack: 15-1/2"L x 2-7/8"H x 3/4"D.