Solid Brass Vertical Action Galley Pump from FYNSPRAY
Vertical plunger pump with a gracefully arched spout. 50 strokes per gallon. 1"diameter tube. Fits 1/2"–5/8" hose. Requires 8 1/2" clearance below counter surface; 9 3/4" above Material: Brass. Capacity: 50 strokes/gal. Dimensions: 9 3/4"H. Cutout Size: 1 1/8". Clearance: 8 1/2".

Noise Reduction Seam Tape from WEST MARINE
The 3/32" flexible vinyl sheet is fused between two layers of foam—an exterior (“decoupler”) layer and an interior (“absorber”) layer. The exterior layer is then covered with a thin film (2. 5 mil) of mylar, reinforced with elastomer-coated fiberglass, for surface heat protection and enhanced sound absorption. The overall effect is a dramatic noise reduction when compared with single-layer foam barriers. Available in two overall thicknesses. Peel and stick backing for easy installation.

Aft-Deck Shower System from ATTWOOD
This compact hot/cold shower stores neatly in its own compartment on the stern or in the head. Includes a handheld shower spray head with shutoff, 6' hose, hot/cold water controls and a cover. Easily hooked into your freshwater system. Compartment is drilled for six #8 fasteners. Material: High-impact plastic . Dimensions: 9-1/2"H x 5"W x 2-1/4"D . Hose Size: 6'L . Port Sizes: 1/2" NPT .

29mm Carbo Clew Block Assembly from HARKEN
From the folks who invented ball bearing blocks, this line of blocks boasts an excellent strength-to-weight ratio. 29mm doubles and triples feature a U-lock to hold the swivel in the front or side position, or allow it to spin freely. Use the 40mm blocks for jib and mainsheet systems on high-performance dinghies, and for high-load control lines on small keelboats. The 57mm blocks have an enormous working range that makes them ideal for main and jib sheets, spinnaker halyards and control lines.

1/8" Single Braid, 2300lb. Breaking Strength, Green from SAMSON ROPE
The high-strength, low-stretch equivalent to wire rope with seven times less weight! Combined with flex-fatigue and service life durability, Amsteel 12-strand Dyneema SK-75 single braid can outlast wire rope and has none of the handling and safety issues associated with wire. Stretch: 0. 70% at 20% of breaking strength. Best Use: Cascade systems, replacements for wire halyards, tapered sheets, backstays, runners, checkstays and strong ultralight rigging . Construction: 12-strand single braid .

1/8" Endura 12 Dyneema Single Braid, 2,100lb. Breaking Strength from NEW ENGLAND ROPES
Extremely high strength-to-weight ratio! Excellent strength-to-weight ratio, ultra-low elongation, excellent flexibility and wet/dry strength retention, torque-free, and it floats. Constructed from Dyneema SK-75, Endura 12 has a proprietary urethane coating for improved abrasion resistance. Best Use: Halyards, sheets, low-stretch control lines, guys, slings/hoisting ropes . Construction: 12-strand single braid . Core Fiber/Construction: Coated Dyneema SK-75 . 0% at 30% of breaking strength .

Flex Trim - Black 1/2" opening from TACO PRODUCTS
For a beautiful finished look on unfinished edges. Just push it on and it's on to stay. Grips on difficult materials, compound curves, etc. Individual corrosion resistant aluminum clips for a permanent grip. Black or White . Sold in 25' lengths. . Available in four sizes:. 5/32" opening x 35/64"H. 1/4" opening x 1/2"H. 3/8" opening x 5/8"H.

Series 150 Clear PVC Tubing, 1/2"ID, 45psi Burst Pressure from SHIELDS RUBBER
Single layer, nontoxic, FDA-approved clear vinyl tubing. Ideal for drain lines, iceboxes, refrigerators, livewells, bilge pump discharge, freshwater lines, water and holding tank vents. Sold per foot: 50’ maximum continuous length for 1/4" and 3/8" hose; 100' maximum continuous length for 1/2" hose and larger. Application: Non-pressurized water system supply; sink, shower, and icebox drains. Material: FDA formula vinyl. Reinforcement: None. Temperature Range: N/A.

1/4" Dia. Stamped Halyard Shackle, 1,000SWL from SCHAEFER
Stamped Halyard Shackles haveflared heads with cross pin retainer for attachment to rope. Captive design prevents accidental opening Quick release pin #93-42 - 1/4" Shackle Pin dia. , 1/2" Inside Width, 1,000 SWL #93-45 - 5/16" Shackle Pin dia.

Clamp-On Rod Holder - 1 1/4"ID Horizontal, Gold from WEST MARINE
1 1/4IN HORIZONTAL MOUNT.

WL/1 Fairlead Model from SPINLOCK
New low-profile design easily mounts to 1" stanchion using internal clamping system. WL/2 sheave model utilizes unique tracker ball angle adjustment. WL/1 Fairlead model includes stainless-steel bullseye for strength.

Deck Fill, Gas, w/Key, 1-1/2" from WHITECAP INDUSTRIES
Stainless-steel deck fills with durable cast heads—not the thin stamped heads found on many imports. Gas, Diesel and Water fills have 1 1/2" openings. Waste fill has 2" opening. All connect to 1 1/2" hose, and include a stainless key. Material: Stainless . Attachment Method: 1 1/2" hose . Flange Diameter: 3" or 3 1/2" (waste) . Fasteners: Three #10 FHMS . Cutout Diameter: 1 5/8" .

Series 60 Orbit Block, Single Light-Load, 2-3/8" Sheave Size, 1,710lb. SWL, 4.7oz. from RONSTAN
These exceptionally strong blocks feature the performance Orbit sheave with captive Acetal ball bearings for side thrust loads, eliminating the need for side retainer plates. The 75mm webbing block (RF79107) can be used where swivel head and shackle attachment is not required to achieve further weight savings. Sheave Size: 2-3/8" (60mm) or 3" (75mm). Line Diameter: Series 60: 1/2" (12mm), Series 75: 9/16" (14mm). Cheek Material/Finish: Anodized aluminum.

Single Channel-Mate Glass Channel, 7/16"W from BECKSON MARINE
This window track is ideal for window glass or for installing sliding cabinet doors. Each channel groove is slightly (. 005") narrower than 1/4" window glass so there is positive pressure against the glass at all times. It seals out leaks and prevents glass from rattling. Made of B-FLEX marine plastic, it will not crack or discolor. The elevated slide at the bottom of the channel makes windows or doors easy to open and close. Sold in 8' lengths.

Stern Rail Outboard Motor Mount - Aluminum for 1-1/4" Railings from EDSON CORPORATION
Built to hold motors up to 15 hp or 100 lbs/45 kg. Convenient cleat and side handles allow you to tie the motor and lock it safely on board. The non-corroding polished 316 stainless bracket with non-skid pad, bolted to the UV stable poly backing board always looks ship-shape… no more varnishing. Bottom cleat comes unattached so that it will fit any rail spacing. Note: 1-1/4” rail version comes complete with anodized aluminum bracket, stainless cleat and stainless U-bolt for 1-1/4” railing.