Flush Lock - Black/Stainless Steel with Adjustable Offset Cam Bar from PERKO
Black plastic with stainless steel "D" ring handle and with adjustable offset cam bar. Two O-rings for increased water resistance. Position indicator shows open or closed position. Door thickness: 3/8" to 1-14" . Face plate dimensions: 2-7/8" x 2-7/8" . Adjustment latch bar: 3/8" to 3" .

Flush Lock and Latch from PERKO
Black plastic, with stainless steel "D" ring handle, stem and lock nut. Two O-rings for increased water resistance. Position indicator shows open or closed position. Lock with 2 keys. Door thickness: 3/8" to 1-1/4" . Face plate dimensions: 2-7/8" x 2-7/8" . Adjustment latch bar: 1-1/16" to 2-9/16" .

Auxiliary Outboard Bracket, 9-1/2" Vertical Lift, 7.5hp-30hp HP Rating from GARELICK
Built extra-tough and extra-wide for secondary engines including new higher-torque, four-stroke engines. Stainless torsion springs for easy lifting. Mounting board is 2" weatherproof and maintenance-free polypropylene. Five-position lock bar allows for better range trim adjustment. Maximum Weight: Model #193328: 169 lbs. , Model # 3683455: 175 lbs. . Style: Adjustable . Material: Anodized aluminum body w/ poly-propylene board . Attachment Method: Thru-bolt, backing plate .

4-Stroke Auxiliary Outboard Bracket from GARELICK
Gets your motor clear of the water when not in use to eliminate propeller drag and to protect the lower unit. Marine-grade stainless steel and a 2" thick polyethylene mounting board. Brackets adjust to transoms with plus or minus angles from 7° to 35° in 7° increments.

T-Top Boat Cover, Center-Line Length 20'5" to 21'4", Blue from TAYLOR
The main features of these covers are: Bow and stern sections are separated into two halves. The sections are joined through the use of a 7mm single pull molded nylon zipper on both the port and starboard sides. Cover design incorporates a "console tube" section with two adjustable straps which lift and secure the cover halves up and over the console body and up under the T-top. The top edge of console tube incorporates an adjustable draw rope in both front and rear sections.

8-1/2" Hatch Holder, Adjustable, for Hatches to 10lb. from MOONLITE MARINE
Stainless, spring-type holders “pop” into place to hold hatches, doors, table leaves, etc. Easy to install. Adjustable model allows opening between 10° and 80°.

T-Top Boat Cover, Center-Line Length 19'5" to 20'4", Blue from TAYLOR
The main features of these covers are: Bow and stern sections are separated into two halves. The sections are joined through the use of a 7mm single pull molded nylon zipper on both the port and starboard sides. Cover design incorporates a "console tube" section with two adjustable straps which lift and secure the cover halves up and over the console body and up under the T-top. The top edge of console tube incorporates an adjustable draw rope in both front and rear sections.

Fleece Fender Cover, Fits Fenders 10" x 26", Black from TAYLOR
Perfect for use with Big B and other center-tube style fenders, these 100% polyester fleece covers will provide posh protection for your boat! Made of rugged, 12-ounce Blizzard fleece, they are UV- light and tear-resistant. The draw string hem enables adjustment for a snug fit and also permits removal for washing.

Transom Adapter for Bracket from FULTON
Lets you remove your outboard bracket and outboard for security and less stress and fatigue on the transom while trailering. A locking device helps theft-proof motor and bracket. Heavy-duty marine-grade aluminum with stainless steel mounting bolts supplied. For Adjustable Brackets above (Models 380321 & 389866).

Trapeze & Vang Cleat from CLAMCLEAT
The cleat has an in-built pulley that offers a compact solution for rigging with a 1:1 or 2:1 advantage, where a quick, positive lock that is easy to release is required. The sailor's preferred choice for adjusting trapeze lines.

60mm Racing Fiddle Block with Becket & Cleat, 882lb. SWL, 12.4oz. from LEWMAR
For chafe-free, low-friction tackles. Sheave: Anodized aluminum alloy . Ball Bearings: Delrin® . Sheave Size: 2-3/8" (60mm) & 1-5/8" (40mm) . Line Dia. : 3/8" max. . Cheek Material/Finish: Anodized aluminum alloy . Shackle/Strap Type: Swivel with three-way locking, drilled-out head . Cleat: Model with cleat: adjustable arm, aluminum cam cleat .

Body Width 2", Vertical Clearance 1", Shackle Diameter 5/16" from ABUS LOCK COMPANY
Set your own easy-to-remember combination on these padlocks with four-pin tumblers. You set the combination using the key provided. All brass internal components and a stainless steel shackle for superior corrosion protection. Type: Combination . Combination Type: Reset-able four tumbler . Material: Brass body and internal components, solid stainless shackle .

Hatch Riser Arm for 20" x 20" Hatch from TAYLOR
Replacement arms for Taylor hatches from 1987 to the present. Universal arms can be left or right.

10mm Ball Stud pair from TAYLOR
Taylor 10mm Ball Stud pair.

ADJ 7-15-DL Whisker Pole, 83"/9lb. Collapsed Length/Weight, 202" Max. Working Length, 2" Tubing Diameters from FORESPAR
These telescoping whisker poles are heavy-duty two-section and three-section aluminum spars which can be extended to lengths up to 17' and securely locked in position by an internal twist lock device. Poles feature self-latching Ultra Series™ fittings on the inboard and outboard ends. Aluminum tubing. End Fitting Inboard: UPX. End Fitting Outboard: UPX.