Top Sellers
SW Inverter/Charger Remote Panel with 50ft. Cable from XANTREX
Designed for use with SW and PS inverter/chargers, the SWRC is a full-function remote control with backlit LCD display. The remote control comes with a standard 25’ (7. 5 m) cable or a 50’ optional (15 m) cable.
|
Rechargeable Signal Air Horn from TAYLOR
Environmentally safe air horn uses air as a propellant, instead of the traditional gas-filled designs. It's economical too. no more expensive refills to buy. Recharges in seconds with a gas station air pump, air compressor, or any other mechanical compressed air source including hand pumps. Works in all weather extremes and can safely be used or stored near sources of heat. Provides approximately 20 blasts per charge. This loud horn puts out a powerful 120db. Meets all USCG regulations.
|
33C Red Jacket Cable, 18' from TELEFLEX
The most widely used cable type in the world. 8" minimum bend radius. Cable adapter kits available for use with Mercury, MerCruiser, Johnson/ Evinrude, and OMC sterndrive. 3" travel.
|
18' Control Cable from TELEFLEX
Fits all Mercury and MerCruiser (1965–present) and Mariner 40hp and over (1993–present) engines. Engine and controls must both be Mercury or MerCruiser to work with these cables. Check engine or throttle ends for stamped length or measure tip-to-tip.
|
4300BC TFX Cable - 20' from TELEFLEX
TfXtreme's unique design assures smoothness and efficiency–with hardly any lost motion–even in the longest and most complex cable routings! This means superior feel at the control, in any boat–performance that had been considered "impossible". TfXtreme achieves the "impossible". Patent-pending splined core to achieves the impossible–easy movement and minimum lost motion.
|
Safe-T QC Helm from TELEFLEX
For use in almost all stern drive, inboard and other power-assisted applications where No Feedback steering is not required. Single Station. Boat Type: All stern drive, inboard, and power-assisted applications. Steering Type: Rotary Safe-T quick helm. Dimensions: 4-7/8"D behind dash front x 6-7/8"W x 5-5/16"H. Steering Wheel: Up to 16". Not included. Steering Wheel Shaft: 3/4" tapered. Cable Type: QC II (SSC62). Mounting Hardware: Included.
|
Big-T Rotary Helm from TELEFLEX
Die-cast gears and added shaft support help it hold up to tough use. For single or twin station powerboats up to 34'. Boat Type: Inboards and power-assisted sterndrives, up to 34' . Steering Type: Rotary . Dimensions: 6-13/16"D behind dash front x 6-3/8"W x 5-1/16"H . Steering Wheel: Up to 20". Not included . Steering Wheel Shaft: 3/4" tapered . Cable Type: QC II SSC61XX or SSC72XX . Mounting Hardware: Requires bezel kit sold separately .
|
Snap-On Cable Cover, 1/4" Wire Dia. from DAVIS INSTRUMENTS
White vinyl cable covers in 6' lengths. Tubes split down length and install in seconds.
|
|
|
|
|
Side-Mount with Trim & Tilt 4-Wire from TELEFLEX
SL-3 is specifically engineered for installation without control modifications. Port or starboard installation with various cable-entry angles. Adapts for push or pull mode without tools. “Easy-On” cable design means no shift or throttle adjustments. Optional trim switch in handle grip for one-hand operation. Functions: Gearshift/throttle . Levers: Dual functions—each lever controls throttle and shift . Lever Material: Metal . Features: Push button for neutral Adjustable brake .
|
Aluminum Transom Support Master Mounting Kit from TELEFLEX
Universal mount for most outboard engine steering applications. This kit includes the Teleflex Outboard Clamp Block, Support Tube, and the Clevis Kit.
|
Teleflex-Bezel For 2' Gauges from TELEFLEX
New! Aircraft Style Square Bezels No cutting or drilling necessary. Fits Amega Pro Series, between gauge and dash.
|
Side Mount - Trim, Tilt, Cut-Off Switch I/O, Chrome from TELEFLEX
Form meets function with these mechanical engine controls. Designed with a contoured grip for ergonomic hand-fitting comfort, these controls also provide a universal fit to any current 3300-/OEM type control cable and adapt to any current engine harness for inboards, outboards and I/Os. Both the Ch1700 side-mount and the CH7500 top-mount with right hand lever feature push-button warm-up and single lever shift and throttle operation with trim in the handle.
|
Twin Straight Handle Control, Chrome from TELEFLEX
Stylish low profile flush mount design available in several function and style options. For single or dual station applications with single or twin engines. Single function (each lever controls shift or throttle). Suits 33C type cables.
|
|
Cable-33 Supreme 7 from TELEFLEX, Cable-33 Supreme 8 from TELEFLEX
|
|
Home -> Engine Systems -> Control Systems -> Control Cables->33C Supreme Red-Jacket Cables
The 33C Supreme has an inner core that's encased in nylon and travels back and forth in a high density polyethylene liner. This plastic against plastic movement decreases friction and increases efficiency by 45% over other push-pull cables. 100% interchangeable with 33C cables. Tight 4'' minimum bend radius capability. Cable adapter kits available for use with Mercury, Mercruiser, Johnson/Evinrude, and OMC sterndrive. . 3'' travel.
Part No: 301947-03-252.0
|
|
|
|
|
Home -> Engine Systems -> Control Systems -> Control Cables->33C Supreme Red-Jacket Cables
The 33C Supreme has an inner core that's encased in nylon and travels back and forth in a high density polyethylene liner. This plastic against plastic movement decreases friction and increases efficiency by 45% over other push-pull cables. 100% interchangeable with 33C cables. Tight 4'' minimum bend radius capability. Cable adapter kits available for use with Mercury, Mercruiser, Johnson/Evinrude, and OMC sterndrive. . 3'' travel.
Part No: 301947-03-264.0
|
|
|
|
|
Home -> Engine Systems -> Control Systems -> Control Cables->33C Supreme Red-Jacket Cables
The 33C Supreme has an inner core that's encased in nylon and travels back and forth in a high density polyethylene liner. This plastic against plastic movement decreases friction and increases efficiency by 45% over other push-pull cables. 100% interchangeable with 33C cables. Tight 4'' minimum bend radius capability. Cable adapter kits available for use with Mercury, Mercruiser, Johnson/Evinrude, and OMC sterndrive. . 3'' travel.
Part No: 301947-03-276.0
|
|
|
|
|
Home -> Engine Systems -> Control Systems -> Control Cables->33C Supreme Red-Jacket Cables
The 33C Supreme has an inner core that's encased in nylon and travels back and forth in a high density polyethylene liner. This plastic against plastic movement decreases friction and increases efficiency by 45% over other push-pull cables. 100% interchangeable with 33C cables. Tight 4'' minimum bend radius capability. Cable adapter kits available for use with Mercury, Mercruiser, Johnson/Evinrude, and OMC sterndrive. . 3'' travel.
Part No: 301947-03-288.0
|
|
|
|
|
Home -> Engine Systems -> Control Systems -> Control Cables->33C Supreme Red-Jacket Cables
The 33C Supreme has an inner core that's encased in nylon and travels back and forth in a high density polyethylene liner. This plastic against plastic movement decreases friction and increases efficiency by 45% over other push-pull cables. 100% interchangeable with 33C cables. Tight 4'' minimum bend radius capability. Cable adapter kits available for use with Mercury, Mercruiser, Johnson/Evinrude, and OMC sterndrive. . 3'' travel.
Part No: 301947-03-312.0
|
|
|
|
|
Home -> Engine Systems -> Control Systems -> Control Cables->33C Supreme Red-Jacket Cables
The 33C Supreme has an inner core that's encased in nylon and travels back and forth in a high density polyethylene liner. This plastic against plastic movement decreases friction and increases efficiency by 45% over other push-pull cables. 100% interchangeable with 33C cables. Tight 4'' minimum bend radius capability. Cable adapter kits available for use with Mercury, Mercruiser, Johnson/Evinrude, and OMC sterndrive. . 3'' travel.
Part No: 301947-03-336.0
|
|
|
|
|
Home -> Engine Systems -> Control Systems -> Control Cables->33C Supreme Red-Jacket Cables
The 33C Supreme has an inner core that's encased in nylon and travels back and forth in a high density polyethylene liner. This plastic against plastic movement decreases friction and increases efficiency by 45% over other push-pull cables. 100% interchangeable with 33C cables. Tight 4'' minimum bend radius capability. Cable adapter kits available for use with Mercury, Mercruiser, Johnson/Evinrude, and OMC sterndrive. . 3'' travel.
Part No: 301947-03-360.0
|
|
|
|
|
Home -> Engine Systems -> Control Systems -> Control Cables->33C Supreme Red-Jacket Cables
The 33C Supreme has an inner core that's encased in nylon and travels back and forth in a high density polyethylene liner. This plastic against plastic movement decreases friction and increases efficiency by 45% over other push-pull cables. 100% interchangeable with 33C cables. Tight 4'' minimum bend radius capability. Cable adapter kits available for use with Mercury, Mercruiser, Johnson/Evinrude, and OMC sterndrive. . 3'' travel.
Part No: 301947-03-384.0
|
|
|
|
|
Home -> Engine Systems -> Control Systems -> Control Cables->33C Supreme Red-Jacket Cables
The 33C Supreme has an inner core that's encased in nylon and travels back and forth in a high density polyethylene liner. This plastic against plastic movement decreases friction and increases efficiency by 45% over other push-pull cables. 100% interchangeable with 33C cables. Tight 4'' minimum bend radius capability. Cable adapter kits available for use with Mercury, Mercruiser, Johnson/Evinrude, and OMC sterndrive. . 3'' travel.
Part No: 301947-03-408.0
|
|
|
|
|
Home -> Engine Systems -> Control Systems -> Control Cables->33C Supreme Red-Jacket Cables
The 33C Supreme has an inner core that's encased in nylon and travels back and forth in a high density polyethylene liner. This plastic against plastic movement decreases friction and increases efficiency by 45% over other push-pull cables. 100% interchangeable with 33C cables. Tight 4'' minimum bend radius capability. Cable adapter kits available for use with Mercury, Mercruiser, Johnson/Evinrude, and OMC sterndrive. . 3'' travel.
Part No: 301947-03-432.0
|
|
|
|
|
Home -> Engine Systems -> Control Systems -> Control Cables->33C Supreme Red-Jacket Cables
The 33C Supreme has an inner core that's encased in nylon and travels back and forth in a high density polyethylene liner. This plastic against plastic movement decreases friction and increases efficiency by 45% over other push-pull cables. 100% interchangeable with 33C cables. Tight 4'' minimum bend radius capability. Cable adapter kits available for use with Mercury, Mercruiser, Johnson/Evinrude, and OMC sterndrive. . 3'' travel.
Part No: 301947-03-456.0
|
|
|
|
|
Home -> Engine Systems -> Control Systems -> Control Cables->33C Supreme Red-Jacket Cables
The 33C Supreme has an inner core that's encased in nylon and travels back and forth in a high density polyethylene liner. This plastic against plastic movement decreases friction and increases efficiency by 45% over other push-pull cables. 100% interchangeable with 33C cables. Tight 4'' minimum bend radius capability. Cable adapter kits available for use with Mercury, Mercruiser, Johnson/Evinrude, and OMC sterndrive. . 3'' travel.
Part No: 301947-03-480.0
|
|
|
|
|
Home -> Engine Systems -> Control Systems -> Control Cables->33C Supreme Red-Jacket Cables
The 33C Supreme has an inner core that's encased in nylon and travels back and forth in a high density polyethylene liner. This plastic against plastic movement decreases friction and increases efficiency by 45% over other push-pull cables. 100% interchangeable with 33C cables. Tight 4'' minimum bend radius capability. Cable adapter kits available for use with Mercury, Mercruiser, Johnson/Evinrude, and OMC sterndrive. . 3'' travel.
Part No: 301947-03-072.0
|
|
|
|
|
Home -> Engine Systems -> Control Systems -> Control Cables->33C Supreme Red-Jacket Cables
The 33C Supreme has an inner core that's encased in nylon and travels back and forth in a high density polyethylene liner. This plastic against plastic movement decreases friction and increases efficiency by 45% over other push-pull cables. 100% interchangeable with 33C cables. Tight 4'' minimum bend radius capability. Cable adapter kits available for use with Mercury, Mercruiser, Johnson/Evinrude, and OMC sterndrive. . 3'' travel.
Part No: 301947-03-084.0
|
|
|
|
|
Home -> Engine Systems -> Control Systems -> Control Cables->33C Supreme Red-Jacket Cables
The 33C Supreme has an inner core that's encased in nylon and travels back and forth in a high density polyethylene liner. This plastic against plastic movement decreases friction and increases efficiency by 45% over other push-pull cables. 100% interchangeable with 33C cables. Tight 4'' minimum bend radius capability. Cable adapter kits available for use with Mercury, Mercruiser, Johnson/Evinrude, and OMC sterndrive. . 3'' travel.
Part No: 301947-03-096.0
|
|
|
|
|
Home -> Engine Systems -> Control Systems -> Control Cables->33C Supreme Red-Jacket Cables
The 33C Supreme has an inner core that's encased in nylon and travels back and forth in a high density polyethylene liner. This plastic against plastic movement decreases friction and increases efficiency by 45% over other push-pull cables. 100% interchangeable with 33C cables. Tight 4'' minimum bend radius capability. Cable adapter kits available for use with Mercury, Mercruiser, Johnson/Evinrude, and OMC sterndrive. . 3'' travel.
Part No: 301947-03-108.0
|
|
|
|
Home -> Engine Systems -> Control Systems -> Control Cables
**Cable Anchor|**Cable Anchor.
Part No: 18-3754
|
|
|
|
Home -> Electrical -> Batteries & Accessories->CableCap Stud Insulators
These simple boots cover positive terminals with an insulating layer of PVC, greatly reducing the chances of accidental shorting with a screwdriver, wrench, etc. and accidental 12V welding.
Part No: 4012
|
|
|
|
|
Home -> Electrical -> Batteries & Accessories->CableCap Stud Insulators
These simple boots cover positive terminals with an insulating layer of PVC, greatly reducing the chances of accidental shorting with a screwdriver, wrench, etc. and accidental 12V welding.
Part No: 4014
|
|
|
|
|
Home -> Electrical -> Batteries & Accessories->CableCap Stud Insulators
These simple boots cover positive terminals with an insulating layer of PVC, greatly reducing the chances of accidental shorting with a screwdriver, wrench, etc. and accidental 12V welding.
Part No: 4010
|
|
|
|
|
Home -> Electrical -> Batteries & Accessories->CableCap Stud Insulators
These simple boots cover positive terminals with an insulating layer of PVC, greatly reducing the chances of accidental shorting with a screwdriver, wrench, etc. and accidental 12V welding.
Part No: 4008
|
|
|
|
Home -> Watersports -> Wakeboards, Kneeboards, Skis & Towables -> Pool/Lake/River
Enjoy the comforts of home while kicking back on the water in this luxurious floating lounge chair—a chair that also can be used as a floating hammock! Built for superior comfort and durability, this unique chair uses two huge pontoons that keep you afloat while functioning as armrests. The seating area consists of four soft 1/2" foam sections that can be removed and used independently without the frame—giving you two separate floats in one. Includes: Convenient hand pump .
Part No: U411BLU-00-000
|
|
|
|
Home -> Navigation -> Charts & Chart Catalogs->Imray-Iolaire Cruising Charts
Designed specifically for the cruising yachtsman, they cover the Caribbean from Puerto Rico to Venezuela, the Atlantic Islands of the Azores, Madeira, Canaries and Bermuda, plus coverage of the Mediterranean.
Part No: A13
|
|
|
|
Home -> Cabin & Galley -> Appliances & Cookware
Durable chrome-plated brass with mounting clip.
Part No: 700301
|
|
|
|
Home -> Navigation -> Charts & Chart Catalogs->Fishing Hot Spots® Charts
Each Fishing Hot Spots® map is thoroughly researched, the information verified and cartography done digitally, with the most current and accurate GIS tools, to ensure an easy-to-read, accurate and affordable map. It's the map successful anglers have asked for by name for more than two decades. Maps come in a variety of sizes and formats. Each body of water is carefully scrutinized and input is gathered from local experts and consumers as to what needs to be part of the product.
Part No: L719
|
|
|
|
Home -> Seating & Covers -> Carpet, Vinyl & Canvas->Sunbrella® Fabric, 46" Wide - By The Linear YARD
Any boat owner knows how the elements can treat a boat, not to mention a boat fabric. But no other marine fabric on earth withstands the ravages of water, sun, salt or wind better than Sunbrella®. You can use Sunbrella® fabric to cover and coordinate your current accessories, or make new ones using your sewing machine Sunbrella® works just as well inside your boat, too. So your baby will look young for a long time. For questions concerning color selection, call our Tech Sales Specialists.
Part No: 300141
|
|
|
|
Home -> Interior, Flags & Gifts -> Gifts -> Keychains, Plaques->Cal June Buoy Float Keyrings
Fun and functional key rings ready to keep your keys afloat for easy retrieval! Choose a horseshoe or ring buoy.
Part No: 87
|
|
|
|
Home -> Fishing -> Fishing Accessories->Aluminum Pliers
Lightweight aluminum pliers won't rust or corrode, snip shark line and downrigger line fast Super lightweight, tough cutting pliers are constructed of T6061 aircraft aluminum with a corrosion-resistant finish for years of use. 420 carbide jaws are strong enough to slice through mono and single strand wire. It will cut through shark fishing line and downrigger wire. Jaws are replaceable.
Part No: C55AP
|
|
|
|
Home -> Fishing -> Fishing Accessories->Calcutta Replacement Jaws for Pliers C55AP
Replaceable jaws are available and come with heat treated #303 stainless screws and tool for easy replacement. 5. 5" Replacement Carbide Jaws. 7.
Part No: 2531-0058
|
|
|
|
|
Home -> Fishing -> Fishing Accessories->Aluminum Pliers
Lightweight aluminum pliers won't rust or corrode, snip shark line and downrigger line fast Super lightweight, tough cutting pliers are constructed of T6061 aircraft aluminum with a corrosion-resistant finish for years of use. 420 carbide jaws are strong enough to slice through mono and single strand wire. It will cut through shark fishing line and downrigger wire. Jaws are replaceable.
Part No: C75AP
|
|
|
