2" ID, 90° Marine Rubber Exhaust Elbow from SHIELDS RUBBER
Exhaust hose elbows let your wet-exhaust line make tight turns without kinking. They provide excellent tolerance to engine heat, vibration and back pressure. Install over rigid tubing or pipe using the four included stainless T-bolt clamps (two at each end). Not intended for hose-to-hose connections. Lubricate with water or detergent. 250°F max.

5" ID, 45° Marine Rubber Exhaust Elbow from SHIELDS RUBBER
Exhaust hose elbows let your wet-exhaust line make tight turns without kinking. They provide excellent tolerance to engine heat, vibration and back pressure. Install over rigid tubing or pipe using the four included stainless T-bolt clamps (two at each end). Not intended for hose-to-hose connections. Lubricate with water or detergent. 250°F max.

Gen-Sep Water Separator, 2" Diameter, Gas In/Out 2.0", Water Outlet 1.5" from CENTEK INDUSTRIES
Position the water drain from the Gen-Sep just below the water line to eliminate water splash, especially important for nighttime operation. Gen-Sep will remove nearly all of the cooling water from the exhaust. That water can then be drained to a hull fitting just below the waterline, thus eliminating excess noise often created by splashing and pulsating water flow at the exhaust outlet. A slight downward angle is required for both the exhaust outlet and the exhaust gas tube. Dimensions: 10.

BK-1 Replacement BilgeKleen Filter from CENTEK INDUSTRIES
We recommend that filters be checked or changed every 3 months.

OSCO CRUSADER ELBOW FOR LOWER SWIVEL from OSCO MOTORS CORP.
Exhaust Elbow Lower Swivel - 3" Outlet Replaces Crusader #97387 .

Series 250 Exhaust Hose, 2-3/8"ID, 2-3/4"OD, 230psi Burst Pressure from SHIELDS RUBBER
For use in all marine water and wet-exhaust applications. Also for marine wet-exhaust where connection requires great length (greater than 4 x ID) or significant bend. Meets or exceeds standards for certified wet-exhaust hose. Sold by the foot with a maximum continuous length of 10' except where preceded by an asterisk, which indicates a maximum continuous length of 50'. Construction: Black synthetic rubber with wire helix and HD synthetic cord . Temperature Range: –20° to 200° F .

Rejuvenate 2-Cycle Engine Oil, Gallon from MERCURY MARINE
Rejuvenate is unlike anything on the market today. It rolls back the clock on engines by quickly removing performance robbing carbon deposits while stabilizing fuel. Powerful detergents remove carbon deposits on piston skirt, crowns and under crowns, power valves, cylinder intake, exhaust and heads. For air-cooled or water-cooled 2-cycle engines with premixed fuel or oil injection systems.

Series 250 Exhaust Hose, 7/8"ID, 1-3/16"OD, 565psi Burst Pressure from SHIELDS RUBBER
For use in all marine water and wet-exhaust applications. Also for marine wet-exhaust where connection requires great length (greater than 4 x ID) or significant bend. Meets or exceeds standards for certified wet-exhaust hose. Sold by the foot with a maximum continuous length of 10' except where preceded by an asterisk, which indicates a maximum continuous length of 50'. Construction: Black synthetic rubber with wire helix and HD synthetic cord . Temperature Range: –20° to 200° F .

Hose Adapter, From 1-1/8" to 3/4"-5/8" from RULE INDUSTRIES
#69 is stepped & adapts from 1-1/8" to 3/4" - 5/8" #57 is an elbow & adapts from 1-1/8" to 1" NPT #67 adapts from 1-1/2" to 1-1/8".

Replacement Delrin Roller, 2-1/2" Dia., 1-3/4 Width from LEWMAR
Anchor rollers make dropping and weighing anchor easier on you and your boat. They help reduce chafe, prevent scratches and dings to your boat’s finish and provide a secure place to store your anchor when used in conjunction with an optional chain stopper or tensioner. We stock rollers to fit the most common combinations of anchor, mounting style and boat. Installation note: overhanging anchor rollers should be supported along at least 2/3 of their length. Easily installed using common tools.

Deck Fill, Gas, w/Key, 1-1/2" from WHITECAP INDUSTRIES
Stainless-steel deck fills with durable cast heads—not the thin stamped heads found on many imports. Gas, Diesel and Water fills have 1 1/2" openings. Waste fill has 2" opening. All connect to 1 1/2" hose, and include a stainless key. Material: Stainless . Attachment Method: 1 1/2" hose . Flange Diameter: 3" or 3 1/2" (waste) . Fasteners: Three #10 FHMS . Cutout Diameter: 1 5/8" .

500gph 12V Bilge Pump, 1.9A Draw at 12V DC, 3/4" Port, 4"H x 2-3/8"W from RULE INDUSTRIES
An internal computer chip cycles these pumps on every 2. 5 minutes, then quickly shuts them down if no water is detected. Built-in strainer bases snap off to make cleaning easy. Completely submersible, rust-proof, corrosion-proof and ignition-protected. Three-way wiring enables connection to a switch for manual override or indicator light. Small 500gph pump is designed to handle spray and rainwater. Built-In Switch: Yes, cycles every 2. 5 min.

Mercury Outboards, 2001-2005, All 2-stroke models, 2.5-250HP from SELOC PUBLICATIONS
SELOC Marine tune-up and repair manuals provide the most comprehensive, authoritative information available for outboard, inboard and stern-drive engines, as well as personal watercraft. SELOC has been the leading source of how-to information for the marine industry since 1974. This manual covers Mercury Outboard, all 2-stroke models, 2. 5-250HP from 2001-2005. Every manual features: Easy-to-follow, step-by-step, illustrated procedures . Hundreds of exploded drawings, photographs and tables .

12 Gallon Topside Fuel Tank from MOELLER
Made from marine grade cross-linked polyethylene for light weight and durability, all tanks are USCG, NMMA and ABYC compliant. Mechanically vented cap floats, and is easy to grip, with ribbed design. Tank includes 90° 1/4"NPT Moeller patented “Poplock” aluminum withdrawal elbow. It swivels 360° without losing its seal. Injection molded 2 1/4" fill neck with gauge and vent. 43"L x 15"W x 6"H.

Exhaust Flapper Valve - 4" from SIERRA
Heavy duty rubber flapper valve keeps following seas from entering exhaust outlet when moving slowly or stopping.