Top Sellers
Deck Fill, Gas, w/Key, 1-1/2" from WHITECAP INDUSTRIES
Stainless-steel deck fills with durable cast heads—not the thin stamped heads found on many imports. Gas, Diesel and Water fills have 1 1/2" openings. Waste fill has 2" opening. All connect to 1 1/2" hose, and include a stainless key. Material: Stainless . Attachment Method: 1 1/2" hose . Flange Diameter: 3" or 3 1/2" (waste) . Fasteners: Three #10 FHMS . Cutout Diameter: 1 5/8" .
|
Roller Shaft Cap Nuts Only - 1/2", Pack of 8 from C E SMITH
Roller Size Length Shaft Diameter Shafts and Nuts 4" 5 1/4" 1/2" 4" 5 1/4" 5/8" 5" 6 1/4" 1/2" 5" 6 1/4" 5/8" 8" 9 1/4" 5/8" 10" 11 1/8" 5/8" 11" 12 3/4" 1/2" 12" 13 1/2" 5/8" Shaft Only 18" 19" 5/8" Cap Nuts Only Packs of 8.
|
Series 150 Clear PVC Tubing, 1/2"ID, 45psi Burst Pressure from SHIELDS RUBBER
Single layer, nontoxic, FDA-approved clear vinyl tubing. Ideal for drain lines, iceboxes, refrigerators, livewells, bilge pump discharge, freshwater lines, water and holding tank vents. Sold per foot: 50’ maximum continuous length for 1/4" and 3/8" hose; 100' maximum continuous length for 1/2" hose and larger. Application: Non-pressurized water system supply; sink, shower, and icebox drains. Material: FDA formula vinyl. Reinforcement: None. Temperature Range: N/A.
|
Series 150 Clear PVC Tubing, 1/4"ID, 60psi Burst Pressure from SHIELDS RUBBER
Single layer, nontoxic, FDA-approved clear vinyl tubing. Ideal for drain lines, iceboxes, refrigerators, livewells, bilge pump discharge, freshwater lines, water and holding tank vents. Sold per foot: 50’ maximum continuous length for 1/4" and 3/8" hose; 100' maximum continuous length for 1/2" hose and larger. Application: Non-pressurized water system supply; sink, shower, and icebox drains. Material: FDA formula vinyl. Reinforcement: None. Temperature Range: N/A.
|
Acetal Thru-Transom Scupper from WEST MARINE
One-way rubber flapper valve and thru-hull fitting. For 1-1/2"ID hose. Overall length: 6-1/4". Installation hole size: 2". Max.
|
Twist Shower, Cold Only from WHALE PUMPS
A refreshing departure from deck shower designs of the past, the innovative Twist offers simple operation in a space-saving, ergonomic design. Spray holes are located in the soft-body handle and a twist of the wrist is all you need to initiate water flow or mix hot with cold. Material: High-impact, glass-filled polypropylene and Nitrile . Dimensions: Side Mount: 4-3/4"dia. x 7-1/2"H (Requires 6"D clearance); Top Mount: 2-5/16"dia. x 7-1/2"D . 2' .
|
Brass-Bristle Brush from SEAFIT
Solid brass bristles won't rust or corrodeLarge, plastic utility brush has solid brass bristles that won’t rust or corrode. Brass bristles are slightly softer than stainless steel and are therefore less intrusive to surfaces. Molded plastic handle provides solid, controlled grip. Bristles: 5/8"D. Overall length: 8 1/2". Molded plastic handle provides solid, controlled grip. 5/8"L bristles.
|
500 RC Windlass, 600lb. Max. Pull, Boat Length 35', 1/4"HT Chain, 1/2" Rope Rode Size, 62'–Chain; 45'–Rope Speed Up/Min., 60' Speed Down/Min., 60A–75A @12V Draw from MAXWELL
These low-profile windlasses feature a patented tension system that maintains resistance required to feed chain/rope rode into the locker instead of jamming it in the windlass. Designed for easy installation, the motor can be oriented in any of 12 positions below decks. Two pieces bolt together quickly. Gasketed, watertight base. For decks to 2 3/4" thick. Capstan models and extra-long shafts for thick decks are available by Special Order. Style: Vertical . Rode Type: Rope/chain .
|
Auxiliary Outboard Bracket, 9-1/2" Vertical Lift, 7.5hp-30hp HP Rating from GARELICK
Built extra-tough and extra-wide for secondary engines including new higher-torque, four-stroke engines. Stainless torsion springs for easy lifting. Mounting board is 2" weatherproof and maintenance-free polypropylene. Five-position lock bar allows for better range trim adjustment. Maximum Weight: Model #193328: 169 lbs. , Model # 3683455: 175 lbs. . Style: Adjustable . Material: Anodized aluminum body w/ poly-propylene board . Attachment Method: Thru-bolt, backing plate .
|
Gunnel Guard - 1/2" Round, 1-1/2" Diameter, 20' Length from TAYLOR
These polyester-covered guards will protect your boat from dings and scratches and they won’t rot in the sun or saltwater like cotton guards. Great for use on dinghies and swim platforms, too. Fabric tabs attach easily with screws or nails. Half Round is for flat surfaces; 3/4 Round is for 90° edges. Sold in 10' or 20' lengths or by the foot up to 50'. Material: Polyester fabric/closed-cell foam . Attachment Method: Screws or nails . Shock Absorption Mechanism: Foam padding .
|
8-1/2" Hatch Holder, Adjustable, for Hatches to 10lb. from MOONLITE MARINE
Stainless, spring-type holders “pop” into place to hold hatches, doors, table leaves, etc. Easy to install. Adjustable model allows opening between 10° and 80°.
|
1-7/8" Polished Brass Flush Ring Pull from ABI
Highly polished brass . Convenient flush-fitting ring pull for cabinets, small doors, and hatches. . 1-7/8"L x 1-1/2"w . Requires four #5 fasteners .
|
Waste Caddy from TODD ENTERPRISES
Todd Waste Caddy A portable 29-gal. capacity waste removal system. Moves easily on pneumatic tires with plastic bearings. Features a vented cap and 10-foot, 1-1/2"dia. hose and gravity-assisted pump that forces out fluid by gravity for a more rapid transfer. Spring-loaded nozzle eliminates leaks . Bronze ball valve is located at the bottom of the tank . Constructed of cross-linked polyethylene for strength and durability .
|
Furler Kit for Boat Length to 16', 500lb. SWL, 1/8" Max. Wire dia., 1/4" Pin dia., 2-1/2" Pin-to-Pin, 5/32" Furling Line dia. from HARKEN
Furl or set your jib from your cockpit Harken small boat furlers allow the sail to be set and furled from the cockpit, a critical convenience in many racing dinghies and trailerable sailboats. Constructed of Hardkote anodized Teflon-impregnated aluminum, they feature multiple stacked races of Delrin or Torlon ball bearings for smooth rotation under load. The jib’s luff wire must be properly seized to the sail, since it carries most of the headstay load. 434 furler for dinghies under 16ft. (4.
|
Fiberglass Boat Cleaner 920 1/2 Gallon from COLLINITE
Removes rust, exhaust, oil, grease, and oxidation stains from fiberglass. Restores the original color quickly without hard rubbing or buffing, leaves a chemically clean surface to which waxes can bond. Use with fiberglass boat wax or heavy-duty paste Fleetwax . Made in U. S. A.
|
|
2", Length 2-1, 2" Pack of 10 from FASCO FASTENERS, Dia #10, Length 1"
|
|
Home -> Fasteners -> Mechanical Fasteners->Bulk Pak Slotted Flat Head Tapping Screws
Type 18-8 stainless steel.
Part No: 500
|
|
|
|
Home -> Fasteners -> Mechanical Fasteners->Wood Screws - Phillips Flat Head - Bulk Pack
Type 18-8 stainless steel.
Part No: 3502
|
|
|
|
Home -> Fasteners -> Mechanical Fasteners->Tapping Screws - Phillips Flat Head - Bulk Packs
Type 18-8 stainless steel.
Part No: 636
|
|
|
|
Home -> Fasteners -> Mechanical Fasteners->Tapping Screws - Slotted Oval Head - Bulk
Type 18-8 stainless steel.
Part No: 450
|
|
|
|
Home -> Fasteners -> Mechanical Fasteners->Tapping Screws - Flat Head - Square Drive - Bulk Packs
Type 18-8 stainless steel.
Part No: 3623
|
|
|
|
Home -> Fasteners -> Mechanical Fasteners->Tapping Screws, Slotted Pan Head, Bulk Packs
Type 18-8 stainless steel.
Part No: 322
|
|
|
|
Home -> Fasteners -> Mechanical Fasteners->Wood Screws - Slotted Oval Head - Bulk Packs
Type 18-8 stainless steel.
Part No: 255
|
|
|
|
Home -> Fasteners -> Mechanical Fasteners -> Retail Packs & Kits->Tapping Screws - Phillips Flat Head
Type 18-8 stainless steel.
Part No: 0636BP
|
|
|
|
Home -> Fasteners -> Mechanical Fasteners -> Retail Packs & Kits->Sheet Metal Screws - Truss Head - Bulk Packs
.
Part No: 663
|
|
|
|
Home -> Fasteners -> Mechanical Fasteners->Wood Screws - Slotted Round Head - Bulk Packs
Type 18-8 stainless steel.
Part No: 216
|
|
|
|
Home -> Fasteners -> Mechanical Fasteners -> Retail Packs & Kits->Tapping Screws - Phillips Pan Head
Type 18-8 stainless steel.
Part No: 0547MP
|
|
|
|
Home -> Fasteners -> Mechanical Fasteners->Tapping Screws - Pan Head - Square Drive - Bulk Packs
Type 18-8 stainless steel.
Part No: 5207
|
|
|
|
Home -> Fasteners -> Mechanical Fasteners->Tapping Screws - Phillips Flat Head - Bulk Packs
Type 18-8 stainless steel.
Part No: 633
|
|
|
|
Home -> Fasteners -> Mechanical Fasteners -> Retail Packs & Kits->Tapping Screws - Phillips Pan Head
Type 18-8 stainless steel.
Part No: 0547BP
|
|
|
|
Home -> Fasteners -> Mechanical Fasteners->Tapping Screws - Phillips Pan Head - Bulk
Type 18-8 stainless steel.
Part No: 547
|
|
|
|
Home -> Fasteners -> Mechanical Fasteners->Tapping Screws, Slotted Pan Head, Bulk Packs
Type 18-8 stainless steel.
Part No: 320
|
|
|
|
Home -> Fasteners -> Mechanical Fasteners -> Retail Packs & Kits->Sheet Metal Screws - Truss Head - Bulk Packs
.
Part No: 661
|
|
|
|
Home -> Fasteners -> Mechanical Fasteners->Wood Screws - Flat Head Slotted - Bulk Packs
Type 18-8 Stainless Steel.
Part No: 293A
|
|
|
|
Home -> Fasteners -> Mechanical Fasteners -> Retail Packs & Kits->Tapping Screws - Phillips Pan Head
Type 18-8 stainless steel.
Part No: 0555MP
|
|
|
|
Home -> Fasteners -> Mechanical Fasteners -> Retail Packs & Kits->Tapping Screws - Phillips Oval Head
Type 18-8 stainless steel.
Part No: 2862MP
|
|
|
|
Home -> Fasteners -> Mechanical Fasteners -> Retail Packs & Kits->Tapping Screws - Phillips Flat Head
Type 18-8 stainless steel.
Part No: 0641MP
|
|
|
|
Home -> Fasteners -> Mechanical Fasteners->Bulk Pak Square Drive Oval Head Tapping Screws
Type 18-8 stainless steel.
Part No: 3477A
|
|
|
|
Home -> Fasteners -> Mechanical Fasteners -> Retail Packs & Kits->Tapping Screws - Phillips Flat Head
Type 18-8 stainless steel.
Part No: 0641BP-A
|
|
|
|
Home -> Fasteners -> Mechanical Fasteners->Tapping Screws - Phillips Pan Head - Bulk
Type 18-8 stainless steel.
Part No: 555A
|
|
|
|
Home -> Fasteners -> Mechanical Fasteners->Tapping Screws - Pan Head - Square Drive - Bulk Packs
Type 18-8 stainless steel.
Part No: 5408A
|
|
|
|
Home -> Fasteners -> Mechanical Fasteners->Tapping Screws - Flat Head - Square Drive - Bulk Packs
Type 18-8 stainless steel.
Part No: 5405A
|
|
|
|
Home -> Fasteners -> Mechanical Fasteners->Bulk Pak Slotted Flat Head Tapping Screws
Type 18-8 stainless steel.
Part No: 506A
|
|
|
|
Home -> Fasteners -> Mechanical Fasteners->Tapping Screws - Slotted Oval Head - Bulk
Type 18-8 stainless steel.
Part No: 455A
|
|
|
|
Home -> Fasteners -> Mechanical Fasteners->Wood Screws - Phillips Flat Head - Bulk Pack
Type 18-8 stainless steel.
Part No: 4120A
|
|
|
|
Home -> Fasteners -> Mechanical Fasteners -> Fasteners (100 Pk Bagged)->Tapping Screws - Phillips Oval Head - Bulk
Type 18-8 stainless steel.
Part No: 2862A
|
|
|