Deck Fill, Waste, w/Key, 1-1/2" from WHITECAP INDUSTRIES
Stainless-steel deck fills with durable cast heads—not the thin stamped heads found on many imports. Gas, Diesel and Water fills have 1 1/2" openings. Waste fill has 2" opening. All connect to 1 1/2" hose, and include a stainless key. Material: Stainless . Attachment Method: 1 1/2" hose . Flange Diameter: 3" or 3 1/2" (waste) . Fasteners: Three #10 FHMS . Cutout Diameter: 1 5/8" .

Deck Fill, Gas, w/Key, 1-1/2" from WHITECAP INDUSTRIES
Stainless-steel deck fills with durable cast heads—not the thin stamped heads found on many imports. Gas, Diesel and Water fills have 1 1/2" openings. Waste fill has 2" opening. All connect to 1 1/2" hose, and include a stainless key. Material: Stainless . Attachment Method: 1 1/2" hose . Flange Diameter: 3" or 3 1/2" (waste) . Fasteners: Three #10 FHMS . Cutout Diameter: 1 5/8" .

1-1/2" Single, 1,500lb. SWL, 2.8oz. from HARKEN
Lightweight, low-friction blocks with hi-load composite bearings carry wire halyards and control line cascades. Side load balls minimize friction from twisting or unfair leads on 304. 300s have thrust washers. Cheek blocks come with fasteners. Sheave: Teflon impregnated Hardkote anodized aluminum. Sheave Size: 1" (25mm), 1-1/2" (38mm), 2" (51mm). Line Diameter: 1" sheave - 3/32"; 1 1/2 sheave - 1/8"; 2"sheave - 3/16".

4000gph Pump, 1-1/2" & 2" Port Sizes, 15A @ 12V DC, 8-1/2"H x 4-3/4"dia. from JOHNSON PUMPS
Designed to meet and exceed the tough demands of commercial and recreational duty, these pumps feature a 12-pole motor with double ball bearings for extended service life. 2200 and 4000 GPH models incorporate a mechanical seal design that eliminates shaft wear. Outlet port check valve included for optional use. Features: Double ball-bearing motors for extended service life . Type: Submersible centrifugal electric bilge pump . Port Sizes: 1-1/8"–2" . Built-In Switch: No .

1600gph Pump, 1-1/8" & 2" Port Sizes, 7A @ 12V DC, 5-7/8"H x 4-1/4"dia. from JOHNSON PUMPS
Designed to meet and exceed the tough demands of commercial and recreational duty, these pumps feature a 12-pole motor with double ball bearings for extended service life. 2200 and 4000 GPH models incorporate a mechanical seal design that eliminates shaft wear. Outlet port check valve included for optional use. Features: Double ball-bearing motors for extended service life . Type: Submersible centrifugal electric bilge pump . Port Sizes: 1-1/8"–2" . Built-In Switch: No .

2200gph Pump, 1-1/8" & 1-1/4" Port Sizes, 8.6A @ 12V DC, 7"H x 4-1/4"dia. from JOHNSON PUMPS
Designed to meet and exceed the tough demands of commercial and recreational duty, these pumps feature a 12-pole motor with double ball bearings for extended service life. 2200 and 4000 GPH models incorporate a mechanical seal design that eliminates shaft wear. Outlet port check valve included for optional use. Features: Double ball-bearing motors for extended service life . Type: Submersible centrifugal electric bilge pump . Port Sizes: 1-1/8"–2" . Built-In Switch: No .

1 1/2" ID Cast 316 Stainless Steel Side Mount Holders from TIGRESS TRADING COMP
1 1/8" & 1 1/2" Outrigger Holders and Replacement Tubes.

Stainless Steel Ultimate Fastener Kit from FASCO FASTENERS
Large quantities make the Ultimate Stainless Steel Fastener kit unique!A very comprehensive selection of the most popular Stainless Steel fasteners, including 8, 10 & 1/4" diameter machine screws up to 2" in length with nuts, nylocks & washers. 10 - 8/32 x 3/4 Phillips Oval Machine Screw . 10 - 8/32 x 1 Phillips Oval Machine Screw . 10 - 8/32 x 1-1/2 Phillips Oval Machine Screw . 10 - 10/24 x 3/4 Phillips Oval Machine Screw . 10 - 10/24 x 1-1/2 Phillips Oval Machine Screw .

Gunnel Guard - 3/4" Round, 1-1/2" Diameter, 10' Length from TAYLOR
These polyester-covered guards will protect your boat from dings and scratches and they won’t rot in the sun or saltwater like cotton guards. Great for use on dinghies and swim platforms, too. Fabric tabs attach easily with screws or nails. Half Round is for flat surfaces; 3/4 Round is for 90° edges. Sold in 10' or 20' lengths or by the foot up to 50'. Material: Polyester fabric/closed-cell foam . Attachment Method: Screws or nails . Shock Absorption Mechanism: Foam padding .

Upper Pintle, 1-1/2" Rudder Thickness, 3-3/8" Strap Length, 1" Strap Width, 1-3/4" Pin Length from SCHAEFER
Typical installations use one with a short pin and one with a long pin. Pin diameter: 1/2". All require #10 RHMS.

Lower Pintle, 1-1/2" Rudder Thickness, 7" Strap Length, 1" Strap Width, 2-3/4" Pin Length from SCHAEFER
Typical installations use one with a short pin and one with a long pin. Pin diameter: 1/2". All require #10 RHMS.

A. West Wight Potter/Buccaneer, Length, 36 1/2", Height at tip 3", Width at butt 1 1/2", Width at tip 1 3/4" from WEST MARINE
Replace that old ugly tiller with a new hand-made laminated ash and mahogany wood tiller, made to fit your rudder hardware, and pre-finished with multiple coats of premium marine spar varnish. Choose the right length and profile, and the butt-end measurements to fit your rudderhead hardware. Can’t find a good fit? Idasailor Marine can custom-build a tiller to your measurements . Custom tillers are shipped direct within 10 days . Click HERE to open the PDF custom order form.

Bullet Block, Double with Becket, 400lb. SWL, 2.8oz. from HARKEN
Available in a wide range of designs, bullet blocks are the foundation of the Harken line, and are adaptable to almost all control line applications. Ideal for cunninghams, vangs, outhauls, traveler controls, spinnaker controls, barberhaulers, etc. Where applicable, blocks use #10 fasteners. Sheave: Delrin® . Ball Bearings: Delrin® . Sheave Size: 1 1/8" (29mm) . Line Dia: 5/16" max. . Cheek Material/Finish: Plastic with stainless strap . Cleat: 094, 095, 291- 423 Carbo-Cam® .

1/4" Dia. Keypin Locking Shackle, 4620lb. Breaking Strength, 3/4" Inside Width from RONSTAN
Clevis pin keeps shackle on end of halyard. Locking pin. RF1032 - 3/16" shackle pin dia. , 2640lb. breaking load. RF1033 - 1/4" shackle pin dia. , 4620lb. breaking load. RF1034 - 5/16" shackle pin dia. , 5940lb.

Bullet Block, Pivoting Exit with Cam, 150lb. SWL, 3.8oz. from HARKEN
Available in a wide range of designs, bullet blocks are the foundation of the Harken line, and are adaptable to almost all control line applications. Ideal for cunninghams, vangs, outhauls, traveler controls, spinnaker controls, barberhaulers, etc. Where applicable, blocks use #10 fasteners. Sheave: Delrin® . Ball Bearings: Delrin® . Sheave Size: 1 1/8" (29mm) . Line Dia: 5/16" max. . Cheek Material/Finish: Plastic with stainless strap . Cleat: 094, 095, 291- 423 Carbo-Cam® .