Brass Reducer, 1/4"NPT x 1/8" FNPT from MOELLER
Barb-Fuel 1/4Fnp x 1/8Mnpt Brs|Barb-Fuel 1/4Fnp x 1/8Mnpt Brs.

Gunnel Guard - 1/2" Round, 1-1/2" Diameter, 20' Length from TAYLOR
These polyester-covered guards will protect your boat from dings and scratches and they won’t rot in the sun or saltwater like cotton guards. Great for use on dinghies and swim platforms, too. Fabric tabs attach easily with screws or nails. Half Round is for flat surfaces; 3/4 Round is for 90° edges. Sold in 10' or 20' lengths or by the foot up to 50'. Material: Polyester fabric/closed-cell foam . Attachment Method: Screws or nails . Shock Absorption Mechanism: Foam padding .

3/16" Stock Dia. U-Bolt, 1-3/8” Thread Length, 1-3/16" Hole Spacing, 1" Eye Dia. from SEAFIT
Stainless steel U-Bolts have metric threads. The top plate is held in place by small ears that are forged into the U-bolt. Includes matching backing plate. ShWt .

8mm (5/16") Stock Dia. Bolt, 4-5/16"L, 5/8" Hole Dia., 3" Stock Length, 1" Plate Dia. from SEADOG
Machined from 304 stainless steel.

Furler Kit for Boat Length to 16', 500lb. SWL, 1/8" Max. Wire dia., 1/4" Pin dia., 2-1/2" Pin-to-Pin, 5/32" Furling Line dia. from HARKEN
Furl or set your jib from your cockpit Harken small boat furlers allow the sail to be set and furled from the cockpit, a critical convenience in many racing dinghies and trailerable sailboats. Constructed of Hardkote anodized Teflon-impregnated aluminum, they feature multiple stacked races of Delrin or Torlon ball bearings for smooth rotation under load. The jib’s luff wire must be properly seized to the sail, since it carries most of the headstay load. 434 furler for dinghies under 16ft. (4.

"Little" Crane, 175 lb. Capacity, 30" Arm Reach, 7:1 Purchase, 75' Line Length from ST. CROIX MARINE
Precision engineered and fabricated from stainless steel, these removable cranes lift heavy loads with ease. Best of all, it takes just 20 seconds to set up or remove for storage. Optional spare mounting kits (VPN #176 & 196) include a set of brackets and rail clamps for an extra mounting location. Material: Polished stainless steel. Height: 60" mast height. Mounting Style: Horizontal or vertical mounting to railing. Included Equipment: Complete kit with mounts and 5/16" line.

5/8" Clevis Pin dia., 1-3/16" inside dia., 4-pack from WEST MARINE
Stainless-Steel Cotter Rings.

Nibo Quick Dog, Right-Locking with Hardware from BOMAR
With these spare parts for your Nibo or Gray hatch, you can replace worn or damaged parts for a fraction of the cost of replacing the hatch. Low-Profile Gasket in a 9' length. 9/16" Gasket in a 10' length. Available for the 100 series: Riser Arm Male Hatch Knob Female Hatch Knob. Hatch Tiedown Dog. Left-Locking Quick Dog.

Screen for Nibo 1070-10A Hatch from BOMAR
With these spare parts for your Nibo or Gray hatch, you can replace worn or damaged parts for a fraction of the cost of replacing the hatch. Low-Profile Gasket in a 9' length. 9/16" Gasket in a 10' length. Available for the 100 series: Riser Arm Male Hatch Knob Female Hatch Knob. Hatch Tiedown Dog. Left-Locking Quick Dog.

SeaStar Helm Seal Kit from TELEFLEX
Replacement shaft seal kit HS5176 fits various post-1990 SeaStar 1. 4, 1. 7 (I), 2. 0, 2. 4 (II), SeaStar Pro and SeaStar helms.

V700 Windlass from LEWMAR
The V700 is a compact, stainless steel windlass designed for power and sail boats. The elegant, low profile design makes windlass an attractive deck accessory. The "FallSafe" gypsy lock takes the load off the gear train while at anchor and also prevents accidental deployment while underway. Includes a heavy-duty, 316 stainless-steel control arm and stripper. Boat Length: to 35' . Rode Type: Rope/chain . Rode Size: 1/4" HT chain, 1/2" rope . Speed Up: 62' (110lb.

Hullgard Primer Converter, Qt. from AWLGRIP
Hullgard Epoxy Primer is a holding primer that combines excellent anticorrosion and water barrier properties with anti-fouling tie-coat functionality. Suitable for below the waterline only, it offers a long overcoating interval without sanding to reduce work time along with superb adhesion to properly prepared fiberglass, steel, aluminum and wood. Can be recoated as soon as the solvents evaporate, even at low temperatures. 1 Gal. Theoretical Coverage – 140 Sq. 5 mils/135 microns DFT or 360 Sq.

Roller Shaft Cap Nuts Only - 1/2", Pack of 8 from C E SMITH
Roller Size Length Shaft Diameter Shafts and Nuts 4" 5 1/4" 1/2" 4" 5 1/4" 5/8" 5" 6 1/4" 1/2" 5" 6 1/4" 5/8" 8" 9 1/4" 5/8" 10" 11 1/8" 5/8" 11" 12 3/4" 1/2" 12" 13 1/2" 5/8" Shaft Only 18" 19" 5/8" Cap Nuts Only Packs of 8.

Flex Trim - Black 1/2" opening from TACO PRODUCTS
For a beautiful finished look on unfinished edges. Just push it on and it's on to stay. Grips on difficult materials, compound curves, etc. Individual corrosion resistant aluminum clips for a permanent grip. Black or White . Sold in 25' lengths. . Available in four sizes:. 5/32" opening x 35/64"H. 1/4" opening x 1/2"H. 3/8" opening x 5/8"H.

Series 150 Clear PVC Tubing, 1/4"ID, 60psi Burst Pressure from SHIELDS RUBBER
Single layer, nontoxic, FDA-approved clear vinyl tubing. Ideal for drain lines, iceboxes, refrigerators, livewells, bilge pump discharge, freshwater lines, water and holding tank vents. Sold per foot: 50’ maximum continuous length for 1/4" and 3/8" hose; 100' maximum continuous length for 1/2" hose and larger. Application: Non-pressurized water system supply; sink, shower, and icebox drains. Material: FDA formula vinyl. Reinforcement: None. Temperature Range: N/A.