Calibrated Resin Pump Set from MAS EPOXY
For use with 1 quart, 1/2 gallon, 1 gallon, 4 gallon and 5 gallon size containers.

Cetol Marine Light - Quart from INTERLUX
Enhances and protects the natural beauty of interior and exterior woodSemi-transparent finish prevents weathering and repels water. just wash wood thoroughly and apply. Three coats are recommended for the first application, followed by annual touchups. Marine Light is more translucent than Marine. If a gloss finish is desired, either may be overcoated with Marine Gloss. Quart. Long-lasting adhesion and protection from UV rays and weathering. Flexible, breathable, translucent finish; Quarts.

Micron CSC Antifouling Paint, Red, Quart from INTERLUX
Haul and relaunch without loss of performance The innovative copper-copolymer formula of Micron CSC provides a controlled release of antifouling biocide at the paint surface, which means that the longevity of the coating is related to the amount of paint applied. Can be applied over most paints in good condition. Micron CSC will not lose its effectiveness when hauled out of the water for extended periods of time (such as winter storage). Type: Copolymer . 2% Cuprous Oxide . Additives: None .

Brightside Pre-Kote Primer - Gray, Quart from INTERLUX
Fills minor blemishes and sands easilyOne part primer for use with Brightside or any other one-part topside enamel. Microspheres provide high build and improved sandability. (Replaces Brightside Primer and 279 White Undercoater. ) Application: Brush, roller, airless/conventional spray . Number of Coats Recommended: One or two, depending on surface condition. Drying: Overcoating: 6 to 12 hrs. Drying Time: To touch: 1 to 3 hrs. Coverage: Brush: 112 sq. ft/qt, 450 sq. ft/gal; Spray: 87 sq.

VC-Offshore - Baltoplate Gray, Gallon from INTERLUX
Used by performance boatsVC Offshore combines superior antifouling performance with a super smooth low friction surface for the performance conscious boater. This high-strength, vinyl antifouling paint, fortified with Teflon® yields a hard, very smooth finish for maximum durability, reduced friction and increased performance. High copper loading fights fouling on performance boats in saltwater. Can be used in fresh, salt and brackish waters. Should not be applied over non-vinyl bottom paints.

CARB GASKET KIT from SIERRA
Sierra carb kits and gaskets for engine tune ups.

Yamaha Carb Kit from SIERRA
Sierra carb kits and gaskets for engine tune ups.

Replaces OMC P/N 378444 from SIERRA
Many of Sierra's solenoids are manufactured by our Independence, KS plant. We produce both starter solenoids and continuous duty solenoids for trim and tilt pumps. Our features add up to solenoids which offer maximum magnetic plunger pull, reduced voltage drop and maximum corrosion protection.

Impeller, 18-3062 from SIERRA
Recommended replacement schedule is every 3 years for fresh water and every year for salt water Click to view a Sierra Impeller Application Chart (PDF) For further assistance, have your year & model information handy and call our Product Advisors at 1-800-BOATING.

For Chrysler/Force, 89-817109A2 from SIERRA
Many of Sierra's solenoids are manufactured by our Independence, KS plant. We produce both starter solenoids and continuous duty solenoids for trim and tilt pumps. Our features add up to solenoids which offer maximum magnetic plunger pull, reduced voltage drop and maximum corrosion protection.

Chris Craft Stain #573 - Pint from INTERLUX
Chris Craft Stain - Pint Fills grain while staining wood, reducing the number of coats of varnish needed. May also be used on bare mahogany planking before applying primer or sanding surfacer.

10 Micron Replacement Filter Element for OMC 502905 from SIERRA
High-performance fuel injected engines require ultimate fuel filtration, separation of water from the fuel supply and maximum fuel flow. Sierra’s new filter elements deliver all three of these critical performance factors. 7900-Series 10 micron filters eliminate harmful contaminants at over 90% efficiency, while removing over 99% of emulsified water. Today’s ethanol-blended fuels increase the chances of water in fuel tanks, resulting in premature wear, poor performance and component damage.

Water Circulating Pump - #18-3581 - Chrysler Inbd # 3004886, 3619542, 3619859, 3745985 from SIERRA
Water Pumps The water pump is the heart of your inboard or I/O cooling system. All Sierra pumps are bidirectional and can be installed on reverse rotation engines. The pumps are also powder coated for additional protection. Includes mounting gasket. Pumps include brass bi-directional impellers, brass plugs and fittings, carbon resin seal, all mounting gaskets, stainless steel seal cup and spring, stainless steel back plate (where required), and powder coating for maximum corrosion protection.

Johnson/Evinrude Outboard Starter, 120 to 140hp V4 (1985-99), 10 tooth drive gear from SIERRA
Sierra's new and remanufactured starters are the only marine starters that meet Marine UL standards. Sierra's remanufactured starters all have new solenoids, drives, bushings, brushes and springs. The bodies are powder coated for greater corrosion resistance. Sierra has entered an agreement with United Technologies to market their complete line of outboard starters and components. All are 100% load tested . Our remanufactured starters are covered by Sierra's customer satisfaction warranty .

30GPH Cartridge, Replaces Racor S3240 from SIERRA
High-performance fuel injected engines require ultimate fuel filtration, separation of water from the fuel supply and maximum fuel flow. Sierra’s filter elements deliver all three of these critical performance factors. 7900-Series 10 micron filters eliminate harmful contaminants at over 90% efficiency, while removing over 98. They’re engineered for today’s sterndrives and inboards, along with 2-cycle and 4-cycle outboards. That is why a high efficiency water separating filter is so important.