2" ID, 90° Marine Rubber Exhaust Elbow from SHIELDS RUBBER
Exhaust hose elbows let your wet-exhaust line make tight turns without kinking. They provide excellent tolerance to engine heat, vibration and back pressure. Install over rigid tubing or pipe using the four included stainless T-bolt clamps (two at each end). Not intended for hose-to-hose connections. Lubricate with water or detergent. 250°F max.

5" ID, 45° Marine Rubber Exhaust Elbow from SHIELDS RUBBER
Exhaust hose elbows let your wet-exhaust line make tight turns without kinking. They provide excellent tolerance to engine heat, vibration and back pressure. Install over rigid tubing or pipe using the four included stainless T-bolt clamps (two at each end). Not intended for hose-to-hose connections. Lubricate with water or detergent. 250°F max.

OSCO CRUSADER ELBOW FOR LOWER SWIVEL from OSCO MOTORS CORP.
Exhaust Elbow Lower Swivel - 3" Outlet Replaces Crusader #97387 .

Exhaust Tube, Mercruiser from SIERRA
Replacement for Mercruiser Inboard/Outboard #32-90949T .

CARB GASKET KIT from SIERRA
Sierra carb kits and gaskets for engine tune ups.

Yamaha Carb Kit from SIERRA
Sierra carb kits and gaskets for engine tune ups.

Outdrive Gasket Set, 18-260, TR/TRS, 1973-1993 from SIERRA
Gasket and O-ring kits that seal the drive to the transom.

Exhaust Bellows - Mercury - Replaces 32734A3, 18654A1 from SIERRA
Seals the exhaust/water flow from the manifold to the exhaust outlet in the drive.

Sierra-Tube-Exhaust from SIERRA
Some larger V-8 engines that create a large amount of back pressure use exhaust tubes rather than bellows. This helps to relieve the excessive pressure and eliminate problems with premature bellows failure. In the past, the exhaust bellows would blow up like a balloon and cause the drive shaft bellows to rub against the yoke and U-joints causing holes in the bellows.

Fits all Cobra. Replaces OMC 914036 from SIERRA
Seals the exhaust/water flow from the manifold to the exhaust outlet in the drive.

Replaces OMC P/N 378444 from SIERRA
Many of Sierra's solenoids are manufactured by our Independence, KS plant. We produce both starter solenoids and continuous duty solenoids for trim and tilt pumps. Our features add up to solenoids which offer maximum magnetic plunger pull, reduced voltage drop and maximum corrosion protection.

Impeller, 18-3062 from SIERRA
Recommended replacement schedule is every 3 years for fresh water and every year for salt water Click to view a Sierra Impeller Application Chart (PDF) For further assistance, have your year & model information handy and call our Product Advisors at 1-800-BOATING.

For Chrysler/Force, 89-817109A2 from SIERRA
Many of Sierra's solenoids are manufactured by our Independence, KS plant. We produce both starter solenoids and continuous duty solenoids for trim and tilt pumps. Our features add up to solenoids which offer maximum magnetic plunger pull, reduced voltage drop and maximum corrosion protection.

Water Circulating Pump - #18-3581 - Chrysler Inbd # 3004886, 3619542, 3619859, 3745985 from SIERRA
Water Pumps The water pump is the heart of your inboard or I/O cooling system. All Sierra pumps are bidirectional and can be installed on reverse rotation engines. The pumps are also powder coated for additional protection. Includes mounting gasket. Pumps include brass bi-directional impellers, brass plugs and fittings, carbon resin seal, all mounting gaskets, stainless steel seal cup and spring, stainless steel back plate (where required), and powder coating for maximum corrosion protection.

Series 250 Exhaust Hose, 2-3/8"ID, 2-3/4"OD, 230psi Burst Pressure from SHIELDS RUBBER
For use in all marine water and wet-exhaust applications. Also for marine wet-exhaust where connection requires great length (greater than 4 x ID) or significant bend. Meets or exceeds standards for certified wet-exhaust hose. Sold by the foot with a maximum continuous length of 10' except where preceded by an asterisk, which indicates a maximum continuous length of 50'. Construction: Black synthetic rubber with wire helix and HD synthetic cord . Temperature Range: –20° to 200° F .