Top Sellers
|
|
Stern Rail Outboard Motor Mount - Aluminum for 1-1/4" Railings from EDSON CORPORATION
Built to hold motors up to 15 hp or 100 lbs/45 kg. Convenient cleat and side handles allow you to tie the motor and lock it safely on board. The non-corroding polished 316 stainless bracket with non-skid pad, bolted to the UV stable poly backing board always looks ship-shape… no more varnishing. Bottom cleat comes unattached so that it will fit any rail spacing. Note: 1-1/4” rail version comes complete with anodized aluminum bracket, stainless cleat and stainless U-bolt for 1-1/4” railing.
|
2-5/8" x 1-1/2" Euro Utility Hinge from WEST MARINE
Stamped utility hinge with 1/2" offset from TACO. Made of marine grade 304 stainless steel with polished finish, non-corrosive utility hinge is ideal for hatches, cabinets, and doors inside and outside the boat. Measures 2-5/8" x 1-1/2" x .
|
Clamp-On Rod Holder - 1 1/4"ID Horizontal, Gold from WEST MARINE
Silver or gold tubes are anodized for long life in the marine environment. Fabricated from cold drawn aluminum with no unsightly weld seams. Available in aluminum schedule pipe sizes 3/4" thru 1 1/4" in horizontal and vertical models. If using stainless steel tube, please go down 1/4" in size. Type:Clamp on. # of Rods:One. Material:Aluminum. Lining:White vinyl. Diameter:Rod holder is 1 5/8" ID. Mount:Clamp on.
|
Hose Adapter, From 1-1/8" to 3/4"-5/8" from RULE INDUSTRIES
#69 is stepped & adapts from 1-1/8" to 3/4" - 5/8" #57 is an elbow & adapts from 1-1/8" to 1" NPT #67 adapts from 1-1/2" to 1-1/8".
|
Deck Fill, Gas, w/Key, 1-1/2" from WHITECAP INDUSTRIES
Stainless-steel deck fills with durable cast heads—not the thin stamped heads found on many imports. Gas, Diesel and Water fills have 1 1/2" openings. Waste fill has 2" opening. All connect to 1 1/2" hose, and include a stainless key. Material: Stainless . Attachment Method: 1 1/2" hose . Flange Diameter: 3" or 3 1/2" (waste) . Fasteners: Three #10 FHMS . Cutout Diameter: 1 5/8" .
|
|
|
1/4" Dia. Stamped Halyard Shackle, 1,000SWL from SCHAEFER
Stamped Halyard Shackles haveflared heads with cross pin retainer for attachment to rope. Captive design prevents accidental opening Quick release pin #93-42 - 1/4" Shackle Pin dia. , 1/2" Inside Width, 1,000 SWL #93-45 - 5/16" Shackle Pin dia.
|
1-7/8" Polished Brass Flush Ring Pull from ABI
Highly polished brass . Convenient flush-fitting ring pull for cabinets, small doors, and hatches. . 1-7/8"L x 1-1/2"w . Requires four #5 fasteners .
|
Acetal Thru-Transom Scupper from WEST MARINE
One-way rubber flapper valve and thru-hull fitting. For 1-1/2"ID hose. Overall length: 6-1/4". Installation hole size: 2". Max.
|
|
|
Twist Shower, Cold Only from WHALE PUMPS
A refreshing departure from deck shower designs of the past, the innovative Twist offers simple operation in a space-saving, ergonomic design. Spray holes are located in the soft-body handle and a twist of the wrist is all you need to initiate water flow or mix hot with cold. Material: High-impact, glass-filled polypropylene and Nitrile . Dimensions: Side Mount: 4-3/4"dia. x 7-1/2"H (Requires 6"D clearance); Top Mount: 2-5/16"dia. x 7-1/2"D . 2' .
|
Rope Deck Pipe from SUNCOR
Accepts up to 3/4" line. Material: Chrome-plated brass . Flange: 4"Dia. I. D. : 1. 75"Dia. .
|
Vertical Plunger Galley Pump, White from FYNSPRAY
Affordable, quality plastic pump with European styling. Vertical plunger action, with a 4" spout. Material: Chrome. Capacity: 58 strokes/gal. Dimensions: 4"H. Cutout Size: 1 1/4". Clearance 9".
|
Flush Lock and Latch from PERKO
Black plastic, with stainless steel "D" ring handle, stem and lock nut. Two O-rings for increased water resistance. Position indicator shows open or closed position. Lock with 2 keys. Door thickness: 3/8" to 1-1/4" . Face plate dimensions: 2-7/8" x 2-7/8" . Adjustment latch bar: 1-1/16" to 2-9/16" .
|
|
from SCHAEFER, 1, 1-1, from FACNOR, from HARKEN, 4" Pin dia
|
|
Home -> Plumbing -> Fittings & Valves->Full-Port Flanged Bronze Seacocks
All-bronze bodies with chrome-plated bronze balls and stainless-steel levers and nuts. Glass-reinforced Teflon seats and seals. Top fitting is NPT (tapered thread) and bottom is NPS (straight thread). Marine UL-listed.
Part No: 78-116-01F
|
|
|
|
|
Home -> Plumbing -> Fittings & Valves->Full-Port Flanged Bronze Seacocks
All-bronze bodies with chrome-plated bronze balls and stainless-steel levers and nuts. Glass-reinforced Teflon seats and seals. Top fitting is NPT (tapered thread) and bottom is NPS (straight thread). Marine UL-listed.
Part No: 78-119-01
|
|
|
|
|
Home -> Plumbing -> Fittings & Valves->Full-Port Flanged Bronze Seacocks
All-bronze bodies with chrome-plated bronze balls and stainless-steel levers and nuts. Glass-reinforced Teflon seats and seals. Top fitting is NPT (tapered thread) and bottom is NPS (straight thread). Marine UL-listed.
Part No: 78-118-01
|
|
|
|
|
Home -> Plumbing -> Fittings & Valves->Full-Port Flanged Bronze Seacocks
All-bronze bodies with chrome-plated bronze balls and stainless-steel levers and nuts. Glass-reinforced Teflon seats and seals. Top fitting is NPT (tapered thread) and bottom is NPS (straight thread). Marine UL-listed.
Part No: 78-120-01
|
|
|
|
|
Home -> Plumbing -> Fittings & Valves->Full-Port Flanged Bronze Seacocks
All-bronze bodies with chrome-plated bronze balls and stainless-steel levers and nuts. Glass-reinforced Teflon seats and seals. Top fitting is NPT (tapered thread) and bottom is NPS (straight thread). Marine UL-listed.
Part No: 78-115-01F
|
|
|
|
Home -> Trailer & Parts -> Hitches, Winches & Jacks -> Hitches, Balls, Receivers
The most popular coupler mechanism ever developed, the Fas-Lok originated with Fulton and is offered in a full line of SAE Class I through IV rated straight tongue stamped couplers. The Fas-Lok latching mechanism allows quick and easy trailer hook-up, and is facotry adjusted for end user convenience. A coupler lock hole is provided for additional trailer security.
Part No: 22200 0101
|
|
|
|
Home -> Trailer & Parts -> Hitches, Winches & Jacks -> Hitches, Balls, Receivers
Your best investment for trailer security Solid cast steel. Heat-treated lock is pick-resistant . Resists rust, corrosion and clogging. Fits all standard couplers and includes two keys.
Part No: HLO 0101
|
|
|
|
Home -> Interior, Flags & Gifts -> Gifts -> Boat Models
Our antiqued Catboats have solid wood hand carved hulls and gaily-striped sails. Easy to rig, they can be placed anywhere and are fun accents in any interior. Color Red. 13. 98" x 4. 53" x 18.
Part No: AS143
|
|
|
|
Home -> Interior, Flags & Gifts -> Gifts -> Boat Models
Our antiqued Catboats have solid wood hand carved hulls and gaily-striped sails. Easy to rig, they can be placed anywhere and are fun accents in any interior. Color Yellow. 13. 98" x 4. 53" x 18.
Part No: AS144
|
|
|
|
Home -> Sailboat -> Headsail Furling -> Headsail Furling->Small Boat Furling Kits
Furl or set your jib from your cockpit Harken small boat furlers allow the sail to be set and furled from the cockpit, a critical convenience in many racing dinghies and trailerable sailboats. Constructed of Hardkote anodized Teflon-impregnated aluminum, they feature multiple stacked races of Delrin or Torlon ball bearings for smooth rotation under load. The jib’s luff wire must be properly seized to the sail, since it carries most of the headstay load. 434 furler for dinghies under 16ft. (4.
Part No: 434
|
|
|
|
Home -> Sailboat -> Headsail Furling -> Headsail Furling->Jib Furling Systems
Using a combination of smooth-rolling Torlon® bearings and a round headstay extrusion centered on the headstay, Schaefer has reduced the effort necessary to roll up a genoa relative to competitive furlers. increases mechanical advantage making furling easier. Open cage design for easy inspection and maintenance. Polyethylene bearing liners stop corrosion and promote smooth furling. Use Norseman or Sta-Lok fittings for easy installation over your existing standard wire headstay and turnbuckle.
Part No: 1100-WL
|
|
|
|
|
Home -> Sailboat -> Headsail Furling -> Headsail Furling->Jib Furling Systems
Using a combination of smooth-rolling Torlon® bearings and a round headstay extrusion centered on the headstay, Schaefer has reduced the effort necessary to roll up a genoa relative to competitive furlers. increases mechanical advantage making furling easier. Open cage design for easy inspection and maintenance. Polyethylene bearing liners stop corrosion and promote smooth furling. Use Norseman or Sta-Lok fittings for easy installation over your existing standard wire headstay and turnbuckle.
Part No: 2100-WL
|
|
|
|
|
Home -> Sailboat -> Headsail Furling -> Headsail Furling->Jib Furling Systems
Using a combination of smooth-rolling Torlon® bearings and a round headstay extrusion centered on the headstay, Schaefer has reduced the effort necessary to roll up a genoa relative to competitive furlers. increases mechanical advantage making furling easier. Open cage design for easy inspection and maintenance. Polyethylene bearing liners stop corrosion and promote smooth furling. Use Norseman or Sta-Lok fittings for easy installation over your existing standard wire headstay and turnbuckle.
Part No: 3100-WL
|
|
|
|
Home -> Sailboat -> Headsail Furling -> Headsail Furling->RC Continuous Line Furling System
The drum’s extreme low-profile increases luff length and puts the foot of the sail closer to the deck. The simple pulley design virtually eliminates troublesome line overrides encountered with standard drum-style systems. The aerodynamic head foil with dual luff grooves makes sail changes fast and the simple tack ring fitting makes it easy to lift the drum for turnbuckle inspection or adjustment. Single line design eliminates drum overrides . Large diameter drum for increased turning power .
Part No: 02001101010
|
|
|
|
|
Home -> Sailboat -> Headsail Furling -> Headsail Furling->RC Continuous Line Furling System
The drum’s extreme low-profile increases luff length and puts the foot of the sail closer to the deck. The simple pulley design virtually eliminates troublesome line overrides encountered with standard drum-style systems. The aerodynamic head foil with dual luff grooves makes sail changes fast and the simple tack ring fitting makes it easy to lift the drum for turnbuckle inspection or adjustment. Single line design eliminates drum overrides . Large diameter drum for increased turning power .
Part No: 02001181412
|
|
|
|
|
Home -> Sailboat -> Headsail Furling -> Headsail Furling->RC Continuous Line Furling System
The drum’s extreme low-profile increases luff length and puts the foot of the sail closer to the deck. The simple pulley design virtually eliminates troublesome line overrides encountered with standard drum-style systems. The aerodynamic head foil with dual luff grooves makes sail changes fast and the simple tack ring fitting makes it easy to lift the drum for turnbuckle inspection or adjustment. Single line design eliminates drum overrides . Large diameter drum for increased turning power .
Part No: 02001221616
|
|
|
|
|
Home -> Sailboat -> Headsail Furling -> Headsail Furling->RC Continuous Line Furling System
The drum’s extreme low-profile increases luff length and puts the foot of the sail closer to the deck. The simple pulley design virtually eliminates troublesome line overrides encountered with standard drum-style systems. The aerodynamic head foil with dual luff grooves makes sail changes fast and the simple tack ring fitting makes it easy to lift the drum for turnbuckle inspection or adjustment. Single line design eliminates drum overrides . Large diameter drum for increased turning power .
Part No: 02001301816
|
|
|
|
Home -> Sailboat -> Blocks -> Blocks->Clear-Step Furling Blocks
This block leads the furling line outside your stanchions to keep furling lines out of the way. Slips over stanchions and secures by a simple set screw.
Part No: 706-44
|
|
|
|
|
Home -> Sailboat -> Blocks -> Blocks->Clear-Step Furling Blocks
This block leads the furling line outside your stanchions to keep furling lines out of the way. Slips over stanchions and secures by a simple set screw.
Part No: 506-44
|
|
|
|
Home -> Sailboat -> Headsail Furling
Stainless steel feeder for all systems. Aligns 35-#8 luff tape prior to entering the main feeder on the extrusion foil. Welded bail for shock cord or line to keep the feeder near the headstay. 5/16" dia.
Part No: 76-30
|
|
|
|
Reliable jib furling for dinghies and trailerable boats is now available in convenient packages, which include the upper swivel, lower drum, and furling line. These systems allow you to furl from the safety of the cockpit, but are not for reefing. All components feature high-strength Torlon bearings riding on precision-machined races designed to maximize bearing contact area and minimize friction. The included furling line is properly sized to handle the loads.
Part No: 550-00
|
|
|
|
|
Reliable jib furling for dinghies and trailerable boats is now available in convenient packages, which include the upper swivel, lower drum, and furling line. These systems allow you to furl from the safety of the cockpit, but are not for reefing. All components feature high-strength Torlon bearings riding on precision-machined races designed to maximize bearing contact area and minimize friction. The included furling line is properly sized to handle the loads.
Part No: 650-00
|
|
|
|
Home -> Sailboat -> Headsail Furling
A sleek, snag-free way to lead your furler's lines back to the cockpit. Clamps around the 7/8" or 1" stanchion tubing, so you don't have to drill any holes.
Part No: RF3
|
|
|
|
Home -> Electrical -> Switches, Fuses & Accessories->ANL Ignition Protected Fuses
Approved for use aboard gas-powered boats. Ignition protected when used in Blue Sea Systems’ fuse blocks. 50-300A fuses use 5003. Tin-plated blades connect to 5/16" studs. Blown condition is visible through window. 6000A interrupt capacity.
Part No: 5125
|
|
|
|
|
Home -> Electrical -> Switches, Fuses & Accessories->ANL Ignition Protected Fuses
Approved for use aboard gas-powered boats. Ignition protected when used in Blue Sea Systems’ fuse blocks. 50-300A fuses use 5003. Tin-plated blades connect to 5/16" studs. Blown condition is visible through window. 6000A interrupt capacity.
Part No: 5126
|
|
|
|
|
Home -> Electrical -> Switches, Fuses & Accessories->ANL Ignition Protected Fuses
Approved for use aboard gas-powered boats. Ignition protected when used in Blue Sea Systems’ fuse blocks. 50-300A fuses use 5003. Tin-plated blades connect to 5/16" studs. Blown condition is visible through window. 6000A interrupt capacity.
Part No: 5127
|
|
|
|
|
Home -> Electrical -> Switches, Fuses & Accessories->ANL Ignition Protected Fuses
Approved for use aboard gas-powered boats. Ignition protected when used in Blue Sea Systems’ fuse blocks. 50-300A fuses use 5003. Tin-plated blades connect to 5/16" studs. Blown condition is visible through window. 6000A interrupt capacity.
Part No: 5129
|
|
|
|
|
Home -> Electrical -> Switches, Fuses & Accessories->ANL Ignition Protected Fuses
Approved for use aboard gas-powered boats. Ignition protected when used in Blue Sea Systems’ fuse blocks. 50-300A fuses use 5003. Tin-plated blades connect to 5/16" studs. Blown condition is visible through window. 6000A interrupt capacity.
Part No: 5131
|
|
|
|
|
Home -> Electrical -> Switches, Fuses & Accessories->ANL Ignition Protected Fuses
Approved for use aboard gas-powered boats. Ignition protected when used in Blue Sea Systems’ fuse blocks. 50-300A fuses use 5003. Tin-plated blades connect to 5/16" studs. Blown condition is visible through window. 6000A interrupt capacity.
Part No: 5133
|
|
|
|
|
Home -> Electrical -> Switches, Fuses & Accessories->ANL Ignition Protected Fuses
Approved for use aboard gas-powered boats. Ignition protected when used in Blue Sea Systems’ fuse blocks. 50-300A fuses use 5003. Tin-plated blades connect to 5/16" studs. Blown condition is visible through window. 6000A interrupt capacity.
Part No: 5135
|
|
|
