Top Sellers
Furler Kit for Boat Length to 16', 500lb. SWL, 1/8" Max. Wire dia., 1/4" Pin dia., 2-1/2" Pin-to-Pin, 5/32" Furling Line dia. from HARKEN
Furl or set your jib from your cockpit Harken small boat furlers allow the sail to be set and furled from the cockpit, a critical convenience in many racing dinghies and trailerable sailboats. Constructed of Hardkote anodized Teflon-impregnated aluminum, they feature multiple stacked races of Delrin or Torlon ball bearings for smooth rotation under load. The jib’s luff wire must be properly seized to the sail, since it carries most of the headstay load. 434 furler for dinghies under 16ft. (4.
|
Snap Furl CF-700 Furling System from SCHAEFER
" Small boat furler comparison, Practical SailorSnapFurl systems come in two sizes to accommodate boats 16' to 24' and boats 24' to 28' and represents the latest in quality Schaefer design and engineering. The efficient Round Geon™ PVC foil snaps quickly and easily around your boat’s existing headstay without the need for special tools or modifications to the rig. System SnapFurl CF-500 for Boats 16’ to 24’ (4. Long fiber reinforced injection molded components make SnapFurl CF 500 unique.
|
2-5/8" x 1-1/2" Euro Utility Hinge from WEST MARINE
Stamped utility hinge with 1/2" offset from TACO. Made of marine grade 304 stainless steel with polished finish, non-corrosive utility hinge is ideal for hatches, cabinets, and doors inside and outside the boat. Measures 2-5/8" x 1-1/2" x .
|
Small Boat Clevis Pin Kit from JOHNSON, C.S.
Assorted sizes of stainless-steel clevis and cotter pins. Small Boat kit contains 46 pieces ranging from 3/16"–5/16".
|
|
|
Stern Rail Outboard Motor Mount - Aluminum for 1-1/4" Railings from EDSON CORPORATION
Built to hold motors up to 15 hp or 100 lbs/45 kg. Convenient cleat and side handles allow you to tie the motor and lock it safely on board. The non-corroding polished 316 stainless bracket with non-skid pad, bolted to the UV stable poly backing board always looks ship-shape… no more varnishing. Bottom cleat comes unattached so that it will fit any rail spacing. Note: 1-1/4” rail version comes complete with anodized aluminum bracket, stainless cleat and stainless U-bolt for 1-1/4” railing.
|
|
|
Hose Adapter, From 1-1/8" to 3/4"-5/8" from RULE INDUSTRIES
#69 is stepped & adapts from 1-1/8" to 3/4" - 5/8" #57 is an elbow & adapts from 1-1/8" to 1" NPT #67 adapts from 1-1/2" to 1-1/8".
|
Deck Fill, Gas, w/Key, 1-1/2" from WHITECAP INDUSTRIES
Stainless-steel deck fills with durable cast heads—not the thin stamped heads found on many imports. Gas, Diesel and Water fills have 1 1/2" openings. Waste fill has 2" opening. All connect to 1 1/2" hose, and include a stainless key. Material: Stainless . Attachment Method: 1 1/2" hose . Flange Diameter: 3" or 3 1/2" (waste) . Fasteners: Three #10 FHMS . Cutout Diameter: 1 5/8" .
|
Clamp-On Rod Holder - 1 1/4"ID Horizontal, Gold from WEST MARINE
Silver or gold tubes are anodized for long life in the marine environment. Fabricated from cold drawn aluminum with no unsightly weld seams. Available in aluminum schedule pipe sizes 3/4" thru 1 1/4" in horizontal and vertical models. If using stainless steel tube, please go down 1/4" in size. Type:Clamp on. # of Rods:One. Material:Aluminum. Lining:White vinyl. Diameter:Rod holder is 1 5/8" ID. Mount:Clamp on.
|
|
|
Hi-Load Ti-Lite Car, Torlon Bearings, 850lb. SWL from HARKEN
These lightweight, solid aluminum and compact captive ball (CB) travelers are built to handle very high loads. Captive ball bearings let you roll the cars on and off the track without using a ball loader. Boat Size: Dinghies, multihulls, to small offshore boats. Material: One-piece solid aluminum . Shackle: Pivoting toggle models—fasten control blocks directly to post without needing a shackle. Sheave: Fixed sheave models—mainsheet loads 40° or less from vertical.
|
1-7/8" Polished Brass Flush Ring Pull from ABI
Highly polished brass . Convenient flush-fitting ring pull for cabinets, small doors, and hatches. . 1-7/8"L x 1-1/2"w . Requires four #5 fasteners .
|
Johnson/Evinrude Outboard, 1971-1989, 1-2Cyl., 1.25-60HP from SELOC PUBLICATIONS
SELOC has been the leading source of how-to information for the marine industry since 1974. Designed and written to serve the needs of the professional mechanic, do-it-yourself boat enthusiast, instructor and student, these manuals are based on actual teardowns done by Seloc’s editors/authors in our on-site facility. 25-60 h. , 1 and 2 cylinders from 1971-1989. Every manual features: Easy-to-follow, step-by-step, illustrated procedures . Hundreds of exploded drawings, photographs and tables .
|
SeaStar Helm Seal Kit from TELEFLEX
Replacement shaft seal kit HS5176 fits various post-1990 SeaStar 1. 4, 1. 7 (I), 2. 0, 2. 4 (II), SeaStar Pro and SeaStar helms.
|
|
Small Boat, 1-1, 2" from LASDROP SHAFT SEALS, 5" from LASDROP SHAFT SEALS
|
|
Home -> Engine Systems -> Propellers & Drive Trains->Gen II Shaft Seal
The Gen II offers exclusive features that make it the premier shaft seal on the market. The Friction Ring assembly is mounted with a rigid connection hose and uses a carbon graphite sealing surface all encased by a durable copolymer housing. Built into the friction ring assembly is a cutlass bearing to ensure proper and constant alignment to the shaft. The Clamp/Pressure Assembly secures the assembly around the shaft, preventing the galling or damage to the shaft that can occur with setscrews.
Part No: G-300-6
|
|
|
|
|
Home -> Engine Systems -> Propellers & Drive Trains->Gen II Shaft Seal
The Gen II offers exclusive features that make it the premier shaft seal on the market. The Friction Ring assembly is mounted with a rigid connection hose and uses a carbon graphite sealing surface all encased by a durable copolymer housing. Built into the friction ring assembly is a cutlass bearing to ensure proper and constant alignment to the shaft. The Clamp/Pressure Assembly secures the assembly around the shaft, preventing the galling or damage to the shaft that can occur with setscrews.
Part No: G-400-512
|
|
|
|
|
Home -> Engine Systems -> Propellers & Drive Trains->Gen II Shaft Seal
The Gen II offers exclusive features that make it the premier shaft seal on the market. The Friction Ring assembly is mounted with a rigid connection hose and uses a carbon graphite sealing surface all encased by a durable copolymer housing. Built into the friction ring assembly is a cutlass bearing to ensure proper and constant alignment to the shaft. The Clamp/Pressure Assembly secures the assembly around the shaft, preventing the galling or damage to the shaft that can occur with setscrews.
Part No: G-400-5
|
|
|
|
|
Home -> Engine Systems -> Propellers & Drive Trains->Gen II Shaft Seal
The Gen II offers exclusive features that make it the premier shaft seal on the market. The Friction Ring assembly is mounted with a rigid connection hose and uses a carbon graphite sealing surface all encased by a durable copolymer housing. Built into the friction ring assembly is a cutlass bearing to ensure proper and constant alignment to the shaft. The Clamp/Pressure Assembly secures the assembly around the shaft, preventing the galling or damage to the shaft that can occur with setscrews.
Part No: G-400-658
|
|
|
|
|
Home -> Engine Systems -> Propellers & Drive Trains->Gen II Shaft Seal
The Gen II offers exclusive features that make it the premier shaft seal on the market. The Friction Ring assembly is mounted with a rigid connection hose and uses a carbon graphite sealing surface all encased by a durable copolymer housing. Built into the friction ring assembly is a cutlass bearing to ensure proper and constant alignment to the shaft. The Clamp/Pressure Assembly secures the assembly around the shaft, preventing the galling or damage to the shaft that can occur with setscrews.
Part No: G-400-6
|
|
|
|
|
Home -> Engine Systems -> Propellers & Drive Trains->Gen II Shaft Seal
The Gen II offers exclusive features that make it the premier shaft seal on the market. The Friction Ring assembly is mounted with a rigid connection hose and uses a carbon graphite sealing surface all encased by a durable copolymer housing. Built into the friction ring assembly is a cutlass bearing to ensure proper and constant alignment to the shaft. The Clamp/Pressure Assembly secures the assembly around the shaft, preventing the galling or damage to the shaft that can occur with setscrews.
Part No: G-400-7
|
|
|
|
|
Home -> Engine Systems -> Propellers & Drive Trains->Gen II Shaft Seal
The Gen II offers exclusive features that make it the premier shaft seal on the market. The Friction Ring assembly is mounted with a rigid connection hose and uses a carbon graphite sealing surface all encased by a durable copolymer housing. Built into the friction ring assembly is a cutlass bearing to ensure proper and constant alignment to the shaft. The Clamp/Pressure Assembly secures the assembly around the shaft, preventing the galling or damage to the shaft that can occur with setscrews.
Part No: G-400-8
|
|
|
|
Home -> Engine Systems -> Engine Parts->Gen-Sep Water Separators
Position the water drain from the Gen-Sep just below the water line to eliminate water splash, especially important for nighttime operation. Gen-Sep will remove nearly all of the cooling water from the exhaust. That water can then be drained to a hull fitting just below the waterline, thus eliminating excess noise often created by splashing and pulsating water flow at the exhaust outlet. A slight downward angle is required for both the exhaust outlet and the exhaust gas tube. Dimensions: 10.
Part No: 1020150
|
|
|
|
|
Home -> Engine Systems -> Engine Parts->Gen-Sep Water Separators
Position the water drain from the Gen-Sep just below the water line to eliminate water splash, especially important for nighttime operation. Gen-Sep will remove nearly all of the cooling water from the exhaust. That water can then be drained to a hull fitting just below the waterline, thus eliminating excess noise often created by splashing and pulsating water flow at the exhaust outlet. A slight downward angle is required for both the exhaust outlet and the exhaust gas tube. Dimensions: 10.
Part No: 1020200
|
|
|
|
Home -> Paint & Maintenance -> Paint, Varnish & Teak Oil->General Adhesive Cleaner
Adhesives clean up easily with thisSpecially blended solvent for easy cleanup of most adhesives. Quickly removes wax, grease, oil and tar. Doesn't harm dried paint, vinyl or fabrics. Great for removing striping tape residue. Excellent for removing Feathering Disk Adhesive. Quart or 20oz.
Part No: 08984
|
|
|
|
Home -> Boats & Motors -> Inflatable Boats->West Marine / Avon / Zodiac Inflatables Accessories
West Marine/Avon /Zodiac Inflatable Accessories.
Part No: N63018
|
|
|
|
Home -> Sailboat -> Blocks->Genoa Lead Blocks
The High Performance car features a roller/ball bearing sheave for higher working loads, and rides on low friction sliders. It has a lever-operated pin stop that operates easily even with cold hands, and can be locked open and used to dead-end an adjustment line. Note: These blocks fit Harken low-profile traveler track Configuration: Twin sheet lead block . Sheave: Anodized aluminum . Ball Bearings: 249, 1537 - Torlon® ball bearings, 1997E -Torlon® roller/ball bearings . : 1/2" max.
Part No: 1997E
|
|
|
|
|
Home -> Sailboat -> Blocks->Genoa Lead Blocks
The High Performance car features a roller/ball bearing sheave for higher working loads, and rides on low friction sliders. It has a lever-operated pin stop that operates easily even with cold hands, and can be locked open and used to dead-end an adjustment line. Note: These blocks fit Harken low-profile traveler track Configuration: Twin sheet lead block . Sheave: Anodized aluminum . Ball Bearings: 249, 1537 - Torlon® ball bearings, 1997E -Torlon® roller/ball bearings . : 1/2" max.
Part No: 1537
|
|
|
|
|
Home -> Sailboat -> Blocks->Genoa Lead Blocks
The High Performance car features a roller/ball bearing sheave for higher working loads, and rides on low friction sliders. It has a lever-operated pin stop that operates easily even with cold hands, and can be locked open and used to dead-end an adjustment line. Note: These blocks fit Harken low-profile traveler track Configuration: Twin sheet lead block . Sheave: Anodized aluminum . Ball Bearings: 249, 1537 - Torlon® ball bearings, 1997E -Torlon® roller/ball bearings . : 1/2" max.
Part No: 249
|
|
|
|
Home -> Sailboat -> Traveler, Tracks & Vang->Genoa Track Slides
Ronstan’s stainless steel slides come with tough plastic inserts which keep the car from scarring the track, while making it easier to move the car. Spring-loaded adjustment pins for fast, positive positioning . Semicircular bails . Slides for 1" track are typically used on boats to 26' . Slides for 1-1/4" track are typically used on boats to 40' .
Part No: RC73202
|
|
|
|
|
Home -> Sailboat -> Traveler, Tracks & Vang->Genoa Track Slides
Ronstan’s stainless steel slides come with tough plastic inserts which keep the car from scarring the track, while making it easier to move the car. Spring-loaded adjustment pins for fast, positive positioning . Semicircular bails . Slides for 1" track are typically used on boats to 26' . Slides for 1-1/4" track are typically used on boats to 40' .
Part No: RC72503
|
|
|
|
Home -> Engine Systems -> Engine Parts
Keep your Genset AIRSEP system running in peak condition with this washable replacement air filter element. Rated for 250 hours between filter cleanings. Washable replacement air filter.
Part No: CD171A
|
|
|
|
Home -> Books & Videos -> Books
Knowing that congress would not approve, George Washington secretly took a small troop to sea and proceeded to attack a British merchant vessel in order to disrupt enemy supply lines.
Part No: 9780071493895
|
|
|
|
Home -> Electronics -> Software -> Nav Charts On CD-ROM->Canadian Hydrographic Service Digital Charts
Canadian Hydrographic Service's digital charts are simple electronic versions of paper charts, popular on pleasure craft.
Part No: RM-CEN06
|
|
|
|
Home -> Interior, Flags & Gifts -> Knives & Pocket Tools -> General Purpose Knives
The emergency knife that cuts but can't puncture On a life raft or inflatable boat where you can't afford a puncture, pointy knives are risky. Gerber's E-Z Out Rescue Knife cuts quickly through line, but its blunt tip is safer for boats and people. Opens fast with one hand. Fiberglass-reinforced thermoplastic handle.
Part No: 46971
|
|
|
|
Home -> Interior, Flags & Gifts -> Knives & Pocket Tools -> General Purpose Knives
A straight spine profile reveals a "seamless" design that begins at the back of the blade and continues along the length of the upper edge of the handle. Seven slanting oval openings in the anodized aluminum handle. The oval openings further reduce the overall weight of these knives. Constructed of 440 stainless steel coated with titanium nitride for added corrosion resistance. Thumb stud for easy one-handed opening.
Part No: 22-41758
|
|
|
|
Home -> Books & Videos -> Books -> Narratives
Includes CD with every possible question and answer on Coast Guard exams and covers all popular Coast Guard captain's licenses. Simulates Coast Guard exams with the AutoExam CD software and replaces or augments classroom instruction costing hundreds of dollars. Table of Contents: Introduction 1. Qualifying for a License 2. Rules of the Road 3. Deck General 4. Navigation General 5. Safety 6. Navigation Problems 7. Auxiliary Sail Endorsement 8. Examination Illustrations 9.
Part No: 9780071603690
|
|
|
|
Home -> Cabin & Galley -> Bedding & Drapery->Velcro® Get-A-Grip
Tough, reusable straps offer stable and secure closure. A convenient and easy way to hold cables, wires, cords and more. Choose from 5-pc multi color or 9' black roll. Easy to use.
Part No: 90340
|
|
|
|
|
Home -> Cabin & Galley -> Bedding & Drapery->Velcro® Get-A-Grip
Tough, reusable straps offer stable and secure closure. A convenient and easy way to hold cables, wires, cords and more. Choose from 5-pc multi color or 9' black roll. Easy to use.
Part No: 90438
|
|
|
|
Home -> Electrical -> Shore Power->GFCI Duplex Outlet
GFCI's measure imbalances in AC circuits, and disrupt service when electrocution danger is likely. Sensitive to a current leak of only 4-6 milliamps. 15-amp capacity; fits standard 15A, three- blade plugs. Installs in standard outlet boxes.
Part No: 1591-FI
|
|
|
|
|
Home -> Electrical -> Shore Power->GFCI Duplex Outlet
GFCI's measure imbalances in AC circuits, and disrupt service when electrocution danger is likely. Sensitive to a current leak of only 4-6 milliamps. 15-amp capacity; fits standard 15A, three- blade plugs. Installs in standard outlet boxes.
Part No: 7879CR-FI
|
|
|
|
Home -> Interior, Flags & Gifts -> Gifts -> Cameras & Equipment->A Collection of Guy Harvey Auto Tags
Guy Harvey is famous for his beautiful recreation of marine life.
Part No: 350-Y005
|
|
|
|
|
Home -> Interior, Flags & Gifts -> Gifts -> Cameras & Equipment->A Collection of Guy Harvey Auto Tags
Guy Harvey is famous for his beautiful recreation of marine life.
Part No: 360-Y048
|
|
|
|
Home -> Interior, Flags & Gifts -> Gifts->Decal Collection by Guy Harvey
Decal Collection by Guy Harvey who is famous for his beautiful recreation of marine life.
Part No: 303-Y048
|
|
|
|
Home -> Interior, Flags & Gifts -> Gifts->Koozie Collection by Guy Harvey
From the Koozie Collection by Guy Harvey who is famous for his beautiful recreation of marine life.
Part No: 457-Y048
|
|
|
