Drill Pump Kit from JABSCO
The self-priming drill pump chucks into a standard 1/4" drill motor and pumps up to 3 1/2gpm. Kit includes all items needed for draining engine oil through the dipstick tube. Includes 3' of 1/2" hose, probe adapter and 40"L x 1/4"dia.

Zinc Grouper Anode from CANADA METALS
Supplements your boat's existing anodes An excellent anodic device to supplement a vessel’s existing anode system, especially to counteract stray current from defective shore power. Clip to bolt on outdrive. Clip to grounding strap if possible or wire items together with copper wire and clip to wire. Do not connect to negative battery terminals. Dimensions: 8 1/4"L x 3 1/4"W x 1 3/8"D.

12 Volt White Dual Trumpet Mini Air Horn from AFI
White epoxy powder-coated finish over solid brass. Noncorrosive Lexan® diaphragm. 12vDC. . Draws 20 amps max. Includes compressor, air tubing, fittings, and hardware. 5" W x 3-3/4"H x 9-1/2" L.

Series 150 Clear PVC Tubing, 1/2"ID, 45psi Burst Pressure from SHIELDS RUBBER
Single layer, nontoxic, FDA-approved clear vinyl tubing. Ideal for drain lines, iceboxes, refrigerators, livewells, bilge pump discharge, freshwater lines, water and holding tank vents. Sold per foot: 50’ maximum continuous length for 1/4" and 3/8" hose; 100' maximum continuous length for 1/2" hose and larger. Application: Non-pressurized water system supply; sink, shower, and icebox drains. Material: FDA formula vinyl. Reinforcement: None. Temperature Range: N/A.

Stern Three-Mile LED Light from ATTWOOD
Energy-efficient three-mile 12" pole anchor/masthead and transom lights. Solid stainless hardware for corrosion resistance and unsurpassed polished appearance. Pole light is direct replacement for Perko 1181DPO CHR used on most Sea Ray boats. Case Material: Stainless steel . Mounting Hardware: Not included . Pole Diameter: 3/4" . Pole Material: Anodized aluminum . Draw: 0. 15A (1. 8W@12V DC) . Volts: 12V DC.

500gph 12V Bilge Pump, 3/4" Port, 1.9A Draw, 2.5A Fuse, 3-1/2"H x 2-3/8"W from RULE INDUSTRIES
Tough and reliable at a value price Great performance at a value price, Rule submersible pumps are the first choice for many boat manufacturers. Their motors feature stainless-steel shafts, water cooling and a vibration-free centrifugal impeller that won’t burn out if run dry. Strainer bases can easily be snapped off for cleaning. Each pump requires a panel switch for manual operation or a float switch for automatic operation. Select from 12V, 24V and 32V models. Can run dry without damage.

8mm (5/16") Stock Dia. Bolt, 4-5/16"L, 5/8" Hole Dia., 3" Stock Length, 1" Plate Dia. from SEADOG
Machined from 304 stainless steel.

Louvered Vent, 7-1/2" x 3-1/2", 3"L Louvers from PERKO
Chromed-plated brass . Drilled for #4 RH screws .

800gph Tsunami Bilge Pump, 2.5A @ 12V DC Draw, 3/4" Port, 4-3/8"H x 3-1/2"W from ATTWOOD
Versatile Tsunami pumps feature interchangeable, twist-and-lock cartridges that reduce maintenance time. All wires are caulked and tinned to prevent water wicking. Rugged glass and mineral-filled polymer construction resists chemicals, fuel and detergents and the compact, low-profile design eases installation in tight spaces.

Fuel Filter Primer Pump Kit from RACOR-PARKER FILTRAT
Prime your fuel line reliably every timeRetrofit this kit to most Racor 1000 or 900 series fuel filters, and you can easily reprime your filter and fuel system. Activate a switch, and fuel is drawn into the pre-screen and pumped through the housing, re-filling the unit. When not in use, the filter pump is bypassed and the fuel/water separator system functions normally. Assembly is only 3. 3" tall .

Deck Fill, Gas, w/Key, 1-1/2" from WHITECAP INDUSTRIES
Stainless-steel deck fills with durable cast heads—not the thin stamped heads found on many imports. Gas, Diesel and Water fills have 1 1/2" openings. Waste fill has 2" opening. All connect to 1 1/2" hose, and include a stainless key. Material: Stainless . Attachment Method: 1 1/2" hose . Flange Diameter: 3" or 3 1/2" (waste) . Fasteners: Three #10 FHMS . Cutout Diameter: 1 5/8" .

500 RC Windlass, 600lb. Max. Pull, Boat Length 35', 1/4"HT Chain, 1/2" Rope Rode Size, 62'–Chain; 45'–Rope Speed Up/Min., 60' Speed Down/Min., 60A–75A @12V Draw from MAXWELL
These low-profile windlasses feature a patented tension system that maintains resistance required to feed chain/rope rode into the locker instead of jamming it in the windlass. Designed for easy installation, the motor can be oriented in any of 12 positions below decks. Two pieces bolt together quickly. Gasketed, watertight base. For decks to 2 3/4" thick. Capstan models and extra-long shafts for thick decks are available by Special Order. Style: Vertical . Rode Type: Rope/chain .

#809 Notched Spreader from WEST SYSTEM
4'' x 4'' plastic spreader with 1/8'', 3/16'' and 1/4'' notches on three sides for quickly applying modified epoxy at a constant thickness.

Vertical Sidelights, White from PERKO
For powerboats and sailboats less than 20m or 65. 6'. Plastic frames with ultrasonically welded lenses and gasketed plastic bases. 2nm visibility. Per pair, except bi-color. Case Material: Plastic . Case Dimensions: 3-1/2"L x 2-1/4"W x 13/16"H . Mounting Hardware: #8 FHMS (sold separately) . Volts: 12V . Draw: 0. 7A .

Drop-In Hidden Horn from AFI
Designed for easy installation, this hidden horn mounts from the outside. Compact in size, but capable of 107db loudness. Comes with both black and white snap-on ASA plastic grilles. A weatherproof fabric liner lets sound through, but keeps water out. Prewired for 12V installation. Material: ABS plastic . Loudness dB: 107dB . Design Standards: Meets ABYC specs for boats up to 12 meters . Dimensions: 2"H x 3-3/8"W x 3-1/4"D . Power Requirements: 12 Volts .