Top Sellers
Flush Kit For 2- & 4-Stroke Outboards from MERCURY MARINE
Fits Mercury/Mariner 4 and 5hp 2-stroke outboards and 4, 5 and 6hp 4-stroke outboards.
|
Roller Shaft Cap Nuts Only - 1/2", Pack of 8 from C E SMITH
Roller Size Length Shaft Diameter Shafts and Nuts 4" 5 1/4" 1/2" 4" 5 1/4" 5/8" 5" 6 1/4" 1/2" 5" 6 1/4" 5/8" 8" 9 1/4" 5/8" 10" 11 1/8" 5/8" 11" 12 3/4" 1/2" 12" 13 1/2" 5/8" Shaft Only 18" 19" 5/8" Cap Nuts Only Packs of 8.
|
500gph 12V Bilge Pump, 1.9A Draw at 12V DC, 3/4" Port, 4"H x 2-3/8"W from RULE INDUSTRIES
An internal computer chip cycles these pumps on every 2. 5 minutes, then quickly shuts them down if no water is detected. Built-in strainer bases snap off to make cleaning easy. Completely submersible, rust-proof, corrosion-proof and ignition-protected. Three-way wiring enables connection to a switch for manual override or indicator light. Small 500gph pump is designed to handle spray and rainwater. Built-In Switch: Yes, cycles every 2. 5 min.
|
Furler Kit for Boat Length to 16', 500lb. SWL, 1/8" Max. Wire dia., 1/4" Pin dia., 2-1/2" Pin-to-Pin, 5/32" Furling Line dia. from HARKEN
Furl or set your jib from your cockpit Harken small boat furlers allow the sail to be set and furled from the cockpit, a critical convenience in many racing dinghies and trailerable sailboats. Constructed of Hardkote anodized Teflon-impregnated aluminum, they feature multiple stacked races of Delrin or Torlon ball bearings for smooth rotation under load. The jib’s luff wire must be properly seized to the sail, since it carries most of the headstay load. 434 furler for dinghies under 16ft. (4.
|
Covered Waterproof Foot Switch from WEST MARINE
Hinged safety cover closes over the switch to prevent accidental operation. 150A continuous rating. 4'' dia. Cutout: 2. 5'' dia.
|
|
|
Flush Cup Door Latch from PERKO
Chrome plated zinc alloy with sliding lock button. For door thickness 3/4 to 1-1/8 inches. Supplied with black plastic spacer for surface mounting. Bevel/Strike Type: Regular w/Box. Case Dimensions: 2-1/8 x 1-3/4 .
|
A - Atlantis Clock - Tide & Time from WEEMS AND PLATH
Hand-polished, fogged brass cases with precision quartz movement. The highly reliable, temperature compensated, aneroid barometer reads in inches and millibars. Barometer movements are calibrated for altitudes to 3500' above sea level. The combination quartz clock and tide clock movement averages the lunar tide cycle. S. Solid cast brass case with protective lacquer coating Screw-type bezel allows easy access Clock features a German movement with bell silencer Dial: 4" Base: 5 1/2".
|
2.4gpm Automatic Pressure Water Pump from WEST MARINE
Quiet and pulsation-free, even at low speeds, our pumps are designed to provide perfect water pressure for single and multiple outlet installations. Compared to older three or four chamber designs, the five chamber design, coupled with cushioned mounting feet, results in lower motor speeds, whisper-quiet operation and dramatically reduced pulsation. GPM: 2. 4Draw @ 12V DC: 7. 0 . Switch Type: Sealed 41 psi pressure switch . Material: Base: Powder-coated steel; Pump body: Powder-coated steel .
|
Small Recessed Transom Shower from SHURFLO
Ideal for mounting to any horizontal surface. Kit includes spray nozzle, hose and necessary hardware for easy installation. White. Material: ABS plastic . Dimensions: 3-7/8"H x 3"W x 2-7/8"L . Port Sizes: 1/2" NPT . Clearance: 2-1/4" .
|
29mm Carbo Clew Block Assembly from HARKEN
From the folks who invented ball bearing blocks, this line of blocks boasts an excellent strength-to-weight ratio. 29mm doubles and triples feature a U-lock to hold the swivel in the front or side position, or allow it to spin freely. Use the 40mm blocks for jib and mainsheet systems on high-performance dinghies, and for high-load control lines on small keelboats. The 57mm blocks have an enormous working range that makes them ideal for main and jib sheets, spinnaker halyards and control lines.
|
Gas Fill & Tank Vent - Black from PERKO
Perko Gas Fill and Tank Vent This ingenious plastic deck fill has a vent with a flame arrestor built right into the fill flange. A flip-up cap eliminates the need for a deck key and no ground wire is required.
|
Flush Lock and Latch from PERKO
Black plastic, with stainless steel "D" ring handle, stem and lock nut. Two O-rings for increased water resistance. Position indicator shows open or closed position. Lock with 2 keys. Door thickness: 3/8" to 1-1/4" . Face plate dimensions: 2-7/8" x 2-7/8" . Adjustment latch bar: 1-1/16" to 2-9/16" .
|
Non-Locking Flush Lock - Chrome/White with Offset Cam Bar from PERKO
Non-Locking chome plated zinc alloy and white plastic with offset adjustable cam bar. Detents indicate open or closed position. Door thickness: 1/4" to 1-1/8" . Face plate dimensions: 2-1/2" x 2-1/2" . Adjustment latch bar: 3/8" to 3" .
|
|
|
|
4" from PERKO, 2" from PERKO, M72 from ICOM, Open-Based Cleat from PERKO
|
|
Home -> Paint & Maintenance -> Paint, Varnish & Teak Oil -> Topside Paint
A flattening agent specifically formulated for mixing with Interlux's one-part finishes, Toplac, Brightside, Yacht Enamels and varnishes (Original, Goldspar Clear and Schooner) to produce a variety of gloss, satin or matte effect finishes. For interior and exterior use.
Part No: YMA715/QT
|
|
|
|
Home -> Engine Systems -> Trim Tabs & Hydrofoils -> Power Tilt/Trim
Same high quality components, capacity and specifications as the hydraulic Power Lift Transom Jacks, above, but adjust manually. Rather than by an hydraulic pump, height is adjusted by turning a 1 -/8" nut on the bottom or the top of the jack with a socket wrench. Then tighten the four side bolts with the same wrench to 100 FPT pounds each. Dimensions: 18-1/8"W x 15-1/2"H - 5-1/2" setback - 5" travel. Material: 6061 T6 aluminum with stainless hardware.
Part No: 65012
|
|
|
|
Home -> Paint & Maintenance -> Cleaners, Soaps & Polishes
All-around cleaner/wax for your boatHeavy-duty Cleaner Wax cleans, shines and protects fiberglass and metal as well as painted surfaces all in one step. Removes oxidation and chalking. Leaves a durable, protective coat. Quart. Cleans, shines and protects fiberglass, metal and painted surfaces in one step. Removes oxidation and leaves a durable, protective coat.
Part No: 089632
|
|
|
|
Home -> Paint & Maintenance -> Cleaners, Soaps & Polishes -> Wax & Protectants
Removes oxidation and restores color and glossClean and restore gloss to your gel coat surface in one step. This aggressive yet safe compound removes moderate to heavy oxidation, scratches, stains and tough water spots on all fiberglass and marine painted gel coat or RV surfaces. It restores color's luster and leave a rich gloss on the treated surface. 32oz. Clean and restore gloss to your gel coat surface in one step. Restores color's luster and leave a rich gloss on the treated surface.
Part No: M6732
|
|
|
|
Home -> Anchor & Docking -> Ladders, Ramps & Boat Hooks -> Swim Platforms/Steps->Polyethylene Dock Steps
Make climbing aboard easier! Durable, U. V. -resistant steps feature StepSafe non-slip pads for maximum slip protection and feature generous 1-1/2" flange for easy deck mounting. Handrails are available for the 2-step and 3-step models. White. One step: 11-15/16" H x 15-1/2" W x 19-1/4" D . Two steps: 17-5/16" H x 20-1/4" W x 21-3/4" D . Three steps: 26" H x 20-1/4" W x 31-3/4" D.
Part No: 91-2333
|
|
|
|
Home -> Trailer & Parts -> Hitches, Winches & Jacks -> Hitches, Balls, Receivers
Installs fast without scratching This 2" hitch ball installs and tightens up quickly with a single wrench when used on Master Lock's One-Tool-Torque ball mounts with no risk of scratching the ball's mirror surface. Also works with Master Lock's Locking Hitch Ball Mount and most other manufacturer's ball mounts.
Part No: 3455DAT
|
|
|
|
Home -> Boats & Motors -> Dinghies -> Rigid Dinghies
One-way assembly drain plug for the Walker Bay 8 & 10.
Part No: 23026
|
|
|
|
Home -> Sailboat -> Traveler, Tracks & Vang
For everything that rolls! Only one drop of this new conditioner will repel salt, dirt and other deposits to protect, lubricate and condition the bearing surfaces. Reduced friction allows balls to roll freely and evenly, greatly improving traveler or battcar performance. 0.
Part No: 7875
|
|
|
|
Home -> Navigation -> Charts & Chart Catalogs->Fishing Hot Spots® Charts
Each Fishing Hot Spots® map is thoroughly researched, the information verified and cartography done digitally, with the most current and accurate GIS tools, to ensure an easy-to-read, accurate and affordable map. It's the map successful anglers have asked for by name for more than two decades. Maps come in a variety of sizes and formats. Each body of water is carefully scrutinized and input is gathered from local experts and consumers as to what needs to be part of the product.
Part No: S490
|
|
|
|
Home -> Navigation -> Charts & Chart Catalogs->Fishing Hot Spots® Charts
Each Fishing Hot Spots® map is thoroughly researched, the information verified and cartography done digitally, with the most current and accurate GIS tools, to ensure an easy-to-read, accurate and affordable map. It's the map successful anglers have asked for by name for more than two decades. Maps come in a variety of sizes and formats. Each body of water is carefully scrutinized and input is gathered from local experts and consumers as to what needs to be part of the product.
Part No: M475
|
|
|
|
Home -> Navigation -> Charts & Chart Catalogs->Fishing Hot Spots® Charts
Each Fishing Hot Spots® map is thoroughly researched, the information verified and cartography done digitally, with the most current and accurate GIS tools, to ensure an easy-to-read, accurate and affordable map. It's the map successful anglers have asked for by name for more than two decades. Maps come in a variety of sizes and formats. Each body of water is carefully scrutinized and input is gathered from local experts and consumers as to what needs to be part of the product.
Part No: A349
|
|
|
|
Home -> Electrical -> Interior Lighting->Opal Bulkhead Lights
Contemporary style bulkhead lights feature composite bases, low-profile rocker switches and frosted glass shades. The rotating base provides easier access to mounting screws. 12V with 10W Xenon “J” bulb included. Light Style: Incandescent Reading Light . Volts: 12V . Bulb Wattage: 10W . Fixture Dimensions: 2. 63" base dia. x 5. 37" x 6. 24" maximum shade dia.
Part No: 8000-BR
|
|
|
|
Home -> Electrical -> Interior Lighting->Opal Bulkhead Lights
Contemporary style bulkhead lights feature composite bases, low-profile rocker switches and frosted glass shades. The rotating base provides easier access to mounting screws. 12V with 10W Xenon “J” bulb included. Light Style: Incandescent Reading Light . Volts: 12V . Bulb Wattage: 10W . Fixture Dimensions: 2. 63" base dia. x 5. 37" x 6. 24" maximum shade dia.
Part No: 8000-CR
|
|
|
|
Home -> Electrical -> Interior Lighting->Opal Bulkhead Lights
Contemporary style bulkhead lights feature composite bases, low-profile rocker switches and frosted glass shades. The rotating base provides easier access to mounting screws. 12V with 10W Xenon “J” bulb included. Light Style: Incandescent Reading Light . Volts: 12V . Bulb Wattage: 10W . Fixture Dimensions: 2. 63" base dia. x 5. 37" x 6. 24" maximum shade dia.
Part No: 8000-WH
|
|
|
|
Home -> Electronics -> Video, Stereos, Weather Radios->VHF Accessories
ICOM VHF Accessories include: Chargers and adapters 12v Lighter cords Battery packs and trays Flush mount kits And more!.
Part No: OPC-1392
|
|
|
|
Home -> Electronics -> Radars->Power Mount & Power Mount Plus Accessories
*Universal mounts fit Furuno, JRC/Northstar, Koden, Lowrance, Sitex, Simrad, Nobeltec, Maptech 12–20" domes and 24" Lowrance domes.
Part No: LTB-OA
|
|
|
|
Home -> Sailboat -> Cleats & Stoppers -> Horn Cleats
We stock a complete selection of cleats for anchoring, docking and general-purpose use. Zinc cleats should be used in fresh water only.
Part No: 1316SPL001
|
|
|
|
Home -> Sailboat -> Cleats & Stoppers -> Horn Cleats->Bronze and Chromed Zinc Cleats
We recommend stainless or bronze cleats for use in fresh or salt water. Zinc and Zamak cleats should be used in fresh water only. We stock a complete selection of cleats for anchoring, docking and general-purpose use.
Part No: 230012
|
|
|
|
Home -> Sailboat -> Cleats & Stoppers -> Horn Cleats->Bronze and Chromed Zinc Cleats
We recommend stainless or bronze cleats for use in fresh or salt water. Zinc and Zamak cleats should be used in fresh water only. We stock a complete selection of cleats for anchoring, docking and general-purpose use.
Part No: 230112
|
|
|
|
Home -> Sailboat -> Cleats & Stoppers -> Horn Cleats->Bronze and Chromed Zinc Cleats
We recommend stainless or bronze cleats for use in fresh or salt water. Zinc and Zamak cleats should be used in fresh water only. We stock a complete selection of cleats for anchoring, docking and general-purpose use.
Part No: 230212
|
|
|
|
Home -> Sailboat -> Cleats & Stoppers -> Horn Cleats->Open-Based Cleats - Chromed Zinc, Plastic Base 4 1/2"
We stock a complete selection of cleats for anchoring, docking and general-purpose use. Zinc cleats should be used in fresh water only. Fasteners not included. 4 1/2" long. Requires four #10 FHMS fasteners.
Part No: 1306DP1CHR
|
|
|
|
Home -> Sailboat -> Cleats & Stoppers -> Horn Cleats
We stock a complete selection of cleats for anchoring, docking and general-purpose use. Zinc cleats should be used in fresh water only. Fasteners not included. 5 3/4" long. Requires two 1/4" FHMS fasteners.
Part No: 1326DP2CHR
|
|
|
|
Home -> Sailboat -> Cleats & Stoppers -> Horn Cleats->Open-Based Cleats - Chromed Zinc, Plastic Base 4 1/2"
We stock a complete selection of cleats for anchoring, docking and general-purpose use. Zinc cleats should be used in fresh water only. Fasteners not included. 4 1/2" long. Requires four #10 FHMS fasteners.
Part No: 1306DP2CHR
|
|
|
|
Home -> Sailboat -> Cleats & Stoppers -> Horn Cleats
We stock a complete selection of cleats for anchoring, docking and general-purpose use. Zinc cleats should be used in fresh water only. Fasteners not included.
Part No: 1316SPL002
|
|
|
|
Home -> Sailboat -> Headsail Furling
Before re-hoisting the bowman doesn’t need to remove the headsail from the luff grove, he just has to open the prefeeder and close it around the luff tape. To open, simply push the spring with your thumb, the jaws will open automatically. The prefeeder can be easily installed below any headsail foil or headsail reefing configuration. In the closed position, it ensures a smooth and easy sail hoist. Stainless-steel product benefiting from the Wichard know-how to offer the highest reliability.
Part No: 7485
|
|
|
|
Home -> Sailboat -> Sailboat Canvas
Holt bouyancy bags are made of tough, heavy-duty, 0. 16" PVC - shaped and finished to fit snug in your dinghy.
Part No: SB2902
|
|
|
|
Home -> Engine Systems -> Engine Lubrication -> 2 Stroke Oil->Opti-Oil
In extreme conditions, this specially-formulated TC-W3 oil adds engine protection for the life of your two-stroke. Burns cleaner and maximizes engine performance.
Part No: 858037Q01
|
|
|
|
Home -> Cabinet & Deck Hardware -> Hatches & Ports -> Hatch Accessories->Breeze-Booster Hatch Ventilating System
Catch the breeze! Funnel the slightest breeze into your boat. Self-supporting system is simple to install in just two steps on power or sail boats and is an efficient way to ventilate your cabin through hatches and portlights. Made of durable ripstop nylon and fiberglass bows with all parts assembled.
Part No: SMALL-SC
|
|
|
|
Home -> Cabinet & Deck Hardware -> Hatches & Ports -> Hatch Accessories->Breeze-Booster Hatch Ventilating System
Catch the breeze! Funnel the slightest breeze into your boat. Self-supporting system is simple to install in just two steps on power or sail boats and is an efficient way to ventilate your cabin through hatches and portlights. Made of durable ripstop nylon and fiberglass bows with all parts assembled.
Part No: MED-SC
|
|
|
|
Home -> Cabinet & Deck Hardware -> Hatches & Ports -> Hatch Accessories->Breeze-Booster Hatch Ventilating System
Catch the breeze! Funnel the slightest breeze into your boat. Self-supporting system is simple to install in just two steps on power or sail boats and is an efficient way to ventilate your cabin through hatches and portlights. Made of durable ripstop nylon and fiberglass bows with all parts assembled.
Part No: LG-SC
|
|
|