PE-1 Lexan Mast Pad Eye from FORESPAR
For use on our small poles. 1-3/4"H x 1-1/4" x 5/8"dia. ring. Same ring as supplied with 4-8 and 6-12 poles.

Roller Shaft Cap Nuts Only - 1/2", Pack of 8 from C E SMITH
Roller Size Length Shaft Diameter Shafts and Nuts 4" 5 1/4" 1/2" 4" 5 1/4" 5/8" 5" 6 1/4" 1/2" 5" 6 1/4" 5/8" 8" 9 1/4" 5/8" 10" 11 1/8" 5/8" 11" 12 3/4" 1/2" 12" 13 1/2" 5/8" Shaft Only 18" 19" 5/8" Cap Nuts Only Packs of 8.

Antifreeze, -100 Engine & Water System - Gallon from SEAFIT
West Marine Pure Oceans -100° (-73°C) Marine Antifreeze provides the ultimate in extreme cold weather and corrosion protection for drinking water systems and all engines. Its premium additive package prevents corrosion of aluminum, copper, brass and solder, but will not harm rubber, seals or hose materials. Provides burst protection to -100°F (-73°C) and freeze protection within a range of -58°F to -63°F (-50°C to - 52°C).

Trapeze & Vang Cleat from CLAMCLEAT
The cleat has an in-built pulley that offers a compact solution for rigging with a 1:1 or 2:1 advantage, where a quick, positive lock that is easy to release is required. The sailor's preferred choice for adjusting trapeze lines.

Flex Trim - Black 1/2" opening from TACO PRODUCTS
For a beautiful finished look on unfinished edges. Just push it on and it's on to stay. Grips on difficult materials, compound curves, etc. Individual corrosion resistant aluminum clips for a permanent grip. Black or White . Sold in 25' lengths. . Available in four sizes:. 5/32" opening x 35/64"H. 1/4" opening x 1/2"H. 3/8" opening x 5/8"H.

Brass Reducer, 1/4"NPT x 1/8" FNPT from MOELLER
Barb-Fuel 1/4Fnp x 1/8Mnpt Brs|Barb-Fuel 1/4Fnp x 1/8Mnpt Brs.

500 RC Windlass, 600lb. Max. Pull, Boat Length 35', 1/4"HT Chain, 1/2" Rope Rode Size, 62'–Chain; 45'–Rope Speed Up/Min., 60' Speed Down/Min., 60A–75A @12V Draw from MAXWELL
These low-profile windlasses feature a patented tension system that maintains resistance required to feed chain/rope rode into the locker instead of jamming it in the windlass. Designed for easy installation, the motor can be oriented in any of 12 positions below decks. Two pieces bolt together quickly. Gasketed, watertight base. For decks to 2 3/4" thick. Capstan models and extra-long shafts for thick decks are available by Special Order. Style: Vertical . Rode Type: Rope/chain .

Rounded Oval, 8-1/2"W x 11-1/4"L x 5-1/4"D, 1" Flange, 1-1/2" Drain from AMBASSADOR MARINE
Made from 304 stainless steel and mirror-polished to a deep luster, these sinks incorporate SoundKOTE Noise Reduction Technology to reduce the unpleasant clanging associated with many metal sinks. Flanges permit over- or under-the-counter mounting. Low-Profile 90° drains fit standard 1"ID hose and are slanted to maximize drainage.

Furler Kit for Boat Length to 16', 500lb. SWL, 1/8" Max. Wire dia., 1/4" Pin dia., 2-1/2" Pin-to-Pin, 5/32" Furling Line dia. from HARKEN
Furl or set your jib from your cockpit Harken small boat furlers allow the sail to be set and furled from the cockpit, a critical convenience in many racing dinghies and trailerable sailboats. Constructed of Hardkote anodized Teflon-impregnated aluminum, they feature multiple stacked races of Delrin or Torlon ball bearings for smooth rotation under load. The jib’s luff wire must be properly seized to the sail, since it carries most of the headstay load. 434 furler for dinghies under 16ft. (4.

A - Atlantis Clock - Tide & Time from WEEMS AND PLATH
Hand-polished, fogged brass cases with precision quartz movement. The highly reliable, temperature compensated, aneroid barometer reads in inches and millibars. Barometer movements are calibrated for altitudes to 3500' above sea level. The combination quartz clock and tide clock movement averages the lunar tide cycle. S. Solid cast brass case with protective lacquer coating Screw-type bezel allows easy access Clock features a German movement with bell silencer Dial: 4" Base: 5 1/2".

FNPT Brass Reducer Fuel Fitting, 1/4" NPT X 1/8" from MOELLER
High quality brass reducer.

G. O'Day 222/Santana 525,Length 47", Height at tip 2 1/4", Width at butt 1 1/2", Width at tip 2" from WEST MARINE
Replace that old ugly tiller with a new hand-made laminated ash and mahogany wood tiller, made to fit your rudder hardware, and pre-finished with multiple coats of premium marine spar varnish. Choose the right length and profile, and the butt-end measurements to fit your rudderhead hardware. Can’t find a good fit? Idasailor Marine can custom-build a tiller to your measurements . Custom tillers are shipped direct within 10 days . Click HERE to open the PDF custom order form.

Step Pad, 10-3/4" x 5-1/4", Blue from LEWMAR
Maintain your footing under all conditions! Self-adhesive, diamond-patterned, nonskid pads are great for decks, steps, dinghy floors, personal watercraft, etc. They resist wear and tear, peeling, saltwater, fuels and chemicals. Pads have rounded edges and are precut to fit most common step sizes. Trim with scissors for a custom fit. Peel-and-stick installation. Sold in pairs.

AC 36-Position Circuit Breaker Panel, 27 Circuit Breakers, 14-3/4" x 11-1/4" from BLUE SEA SYSTEMS
Blue Sea Systems designs innovative, reliable, superior quality electrical system products. Blue Sea Systems products are tested aboard the company's boat to ensure reliability and ease of use in real world conditions. This results in the delivery of innovative, reliable electrical products that exceed the quality standards of other companies. Blue Sea Systems' in-house lab is used to load test and thermal test products to ensure they will perform under marine conditions. Digital Multimeter.

1-1/8" Nylon In-Line Check Valve from GUZZLER/BOSWORTH
Noncorroding nylon.