Spinnaker Pole Car, Track #2720, 900sq.ft. Max. Sail Area, 1125lb. SWL from HARKEN
Now with captive ball bearings, which eliminates the need for a ball-bearing loader during installation or removal from track. These cars run freely, fit low-beam traveler track and are easy to adjust under any load.

Hi-Load Ti-Lite Car, Torlon Bearings, 850lb. SWL from HARKEN
These lightweight, solid aluminum and compact captive ball (CB) travelers are built to handle very high loads. Captive ball bearings let you roll the cars on and off the track without using a ball loader. Boat Size: Dinghies, multihulls, to small offshore boats. Material: One-piece solid aluminum . Shackle: Pivoting toggle models—fasten control blocks directly to post without needing a shackle. Sheave: Fixed sheave models—mainsheet loads 40° or less from vertical.

Furler Kit for Boat Length to 16', 500lb. SWL, 1/8" Max. Wire dia., 1/4" Pin dia., 2-1/2" Pin-to-Pin, 5/32" Furling Line dia. from HARKEN
Furl or set your jib from your cockpit Harken small boat furlers allow the sail to be set and furled from the cockpit, a critical convenience in many racing dinghies and trailerable sailboats. Constructed of Hardkote anodized Teflon-impregnated aluminum, they feature multiple stacked races of Delrin or Torlon ball bearings for smooth rotation under load. The jib’s luff wire must be properly seized to the sail, since it carries most of the headstay load. 434 furler for dinghies under 16ft. (4.

PAR-Max 4 Water-System Pump, 12V from JABSCO
Flow rate: 16. 3 Litres/min (4. 3 gallons/min) Self-priming from dry up to 2. 4m (7. 8ft) Smooth flow. Dry running capability. Soft noise absorbing mounts. Snap-fit port fittings. Corrosion resistant materials. Meets USCG Regulation 183. 410 and ISO 8846 MARINE (ignition protection).

CARB GASKET KIT from SIERRA
Sierra carb kits and gaskets for engine tune ups.

Yamaha Carb Kit from SIERRA
Sierra carb kits and gaskets for engine tune ups.

Replaces OMC P/N 378444 from SIERRA
Many of Sierra's solenoids are manufactured by our Independence, KS plant. We produce both starter solenoids and continuous duty solenoids for trim and tilt pumps. Our features add up to solenoids which offer maximum magnetic plunger pull, reduced voltage drop and maximum corrosion protection.

Impeller, 18-3062 from SIERRA
Recommended replacement schedule is every 3 years for fresh water and every year for salt water Click to view a Sierra Impeller Application Chart (PDF) For further assistance, have your year & model information handy and call our Product Advisors at 1-800-BOATING.

For Chrysler/Force, 89-817109A2 from SIERRA
Many of Sierra's solenoids are manufactured by our Independence, KS plant. We produce both starter solenoids and continuous duty solenoids for trim and tilt pumps. Our features add up to solenoids which offer maximum magnetic plunger pull, reduced voltage drop and maximum corrosion protection.

30GPH Cartridge, Replaces Racor S3240 from SIERRA
High-performance fuel injected engines require ultimate fuel filtration, separation of water from the fuel supply and maximum fuel flow. Sierra’s filter elements deliver all three of these critical performance factors. 7900-Series 10 micron filters eliminate harmful contaminants at over 90% efficiency, while removing over 98. They’re engineered for today’s sterndrives and inboards, along with 2-cycle and 4-cycle outboards. That is why a high efficiency water separating filter is so important.

60GPH Cartridge, Replaces Racor S3227 from SIERRA
High-performance fuel injected engines require ultimate fuel filtration, separation of water from the fuel supply and maximum fuel flow. Sierra’s filter elements deliver all three of these critical performance factors. 7900-Series 10 micron filters eliminate harmful contaminants at over 90% efficiency, while removing over 98. They’re engineered for today’s sterndrives and inboards, along with 2-cycle and 4-cycle outboards. That is why a high efficiency water separating filter is so important.

57mm Black Magic AirBlock, High-Load Strap Head with Becket, 2,500lb. SWL, 3.6oz. from HARKEN
Strong, lightweight aluminum blocks for offshore boats Used for sheets, halyards, running backstays and control lines on offshore boats, these strong, lightweight blocks are made of sculpted aluminum with Torlon rollers and carbon black balls for strength and UV protection. Cheek Material/Finish: 6160-T6 Hardkote anodized aluminum . Sheave Size: 57mm (2-1/4") . Construction: Three fasteners for quick disassembly. Plastic isolators separate dissimilar metals. Three-way head system.

Premium 4-Cycle Heavy-Duty SAE 15W40 Engine Oil, Gallon from WEST MARINE
An excellent choice for all 4-cycle inboard diesel and gasoline engines operating in all conditions. Clean-burning formula meets or exceeds both industry and factory performance specifications. Powerful additives allow for dependable engine service.

RigTune Pro Digital Rig Tension Gauge from HARKEN
Old-fashioned spring gauges, like the Loos Pro, don’t provide repeatable numbers. This product does. Unlike spring-loaded gauges, the Harken Rigtune Pro measures rig tension to the nearest kilogram. A load cell records the pressure on one of the pins and the measurement is displayed on a simple, easy-to-read screen. The Rigtune Pro fits a specific range of rigging sizes, 2. As rigging is deflected over three pins on the back of the gauge, a load cell records the pressure on one of the pins.

10 Micron Replacement Filter Element for OMC 502905 from SIERRA
High-performance fuel injected engines require ultimate fuel filtration, separation of water from the fuel supply and maximum fuel flow. Sierra’s new filter elements deliver all three of these critical performance factors. 7900-Series 10 micron filters eliminate harmful contaminants at over 90% efficiency, while removing over 99% of emulsified water. Today’s ethanol-blended fuels increase the chances of water in fuel tanks, resulting in premature wear, poor performance and component damage.