Low-Permeation Fuel Hose, 1/2" ID, 250' Max. Length from SHIELDS RUBBER
Special design NBR tube with an embedded plastic barrier layer limits permeation. The design of this hose provides easy coupling insertion and the NBR/PVC cover is weather and UV resistant. The hose is also polyester reinforced and fire-resistant. Fuel Type: Fuel feed (gasoline up to 85% ethanol blended fuels/diesel/bio-diesel all blends) . Approvals: SAE J1527 Type A1-15 and ISO 7840 Type A1 . Construction: Reinforced with high strength synthetics to resist gasoline/alcohol permeation .

5" ID, 45° Marine Rubber Exhaust Elbow from SHIELDS RUBBER
Exhaust hose elbows let your wet-exhaust line make tight turns without kinking. They provide excellent tolerance to engine heat, vibration and back pressure. Install over rigid tubing or pipe using the four included stainless T-bolt clamps (two at each end). Not intended for hose-to-hose connections. Lubricate with water or detergent. 250°F max.

2" ID, 90° Marine Rubber Exhaust Elbow from SHIELDS RUBBER
Exhaust hose elbows let your wet-exhaust line make tight turns without kinking. They provide excellent tolerance to engine heat, vibration and back pressure. Install over rigid tubing or pipe using the four included stainless T-bolt clamps (two at each end). Not intended for hose-to-hose connections. Lubricate with water or detergent. 250°F max.

Series 250 Exhaust Hose, 7/8"ID, 1-3/16"OD, 565psi Burst Pressure from SHIELDS RUBBER
For use in all marine water and wet-exhaust applications. Also for marine wet-exhaust where connection requires great length (greater than 4 x ID) or significant bend. Meets or exceeds standards for certified wet-exhaust hose. Sold by the foot with a maximum continuous length of 10' except where preceded by an asterisk, which indicates a maximum continuous length of 50'. Construction: Black synthetic rubber with wire helix and HD synthetic cord . Temperature Range: –20° to 200° F .

Series 150 Clear PVC Tubing, 1/2"ID, 45psi Burst Pressure from SHIELDS RUBBER
Single layer, nontoxic, FDA-approved clear vinyl tubing. Ideal for drain lines, iceboxes, refrigerators, livewells, bilge pump discharge, freshwater lines, water and holding tank vents. Sold per foot: 50’ maximum continuous length for 1/4" and 3/8" hose; 100' maximum continuous length for 1/2" hose and larger. Application: Non-pressurized water system supply; sink, shower, and icebox drains. Material: FDA formula vinyl. Reinforcement: None. Temperature Range: N/A.

Series 250 Exhaust Hose, 2-3/8"ID, 2-3/4"OD, 230psi Burst Pressure from SHIELDS RUBBER
For use in all marine water and wet-exhaust applications. Also for marine wet-exhaust where connection requires great length (greater than 4 x ID) or significant bend. Meets or exceeds standards for certified wet-exhaust hose. Sold by the foot with a maximum continuous length of 10' except where preceded by an asterisk, which indicates a maximum continuous length of 50'. Construction: Black synthetic rubber with wire helix and HD synthetic cord . Temperature Range: –20° to 200° F .

Tee Type Sanitation Hose Fitting, Slip Fitting Thread from SHIELDS RUBBER
Fiberglass-reinforced nylon fittings designed to fit Shields Series 101, 148 and 144 hoses without heating or special tools. Use in sanitation systems, deck drain systems and water tank fill.

Series 315 Outboard Fuel Hose - 3/8"ID from SHIELDS RUBBER
Premium-quality fuel hose designed for outboard feed and vent lines. Remains flexible at low temperatures and resists UV sunlight. Silverado 2000 complies with SAE J1527 Type B2 specifications. Should not be used in applications requiring the use of Type B1 fuel feed line.

Telescopic Tiller Extension 29" - 48" from RONSTAN
Ronstan tiller extensions feature fluted anodized aluminum tubing for durability and rigidity and a tapered, non-slip Hyperlon grip with ball end. The Urethane universal joint can be removed without tools. Adjustable-length versions feature a fast-action adjustable shaft for additional versatility. 4732913 Aluminum Fixed 24” RF3128 5/8"Tubing Dia. , 1"Grip Dia. , 24"L, 5. 3Lbs. 1133131 Lightweight Aluminum 33” RF3129 5/8"Tubing Dia. , 1"Grip Dia.

29mm Carbo Clew Block Assembly from HARKEN
From the folks who invented ball bearing blocks, this line of blocks boasts an excellent strength-to-weight ratio. 29mm doubles and triples feature a U-lock to hold the swivel in the front or side position, or allow it to spin freely. Use the 40mm blocks for jib and mainsheet systems on high-performance dinghies, and for high-load control lines on small keelboats. The 57mm blocks have an enormous working range that makes them ideal for main and jib sheets, spinnaker halyards and control lines.

Delrin Sheave, 1/2" Max. Line Dia., 1-7/16" OD, 3/8" ID, 5/8" Width from SCHAEFER
Schaefer sheaves are designed to be compatible with Schaefer products, and are not intended for use in other manufacturer's blocks. Delrin sheaves are injection molded with UV inhibitors and monitored molding cycles for a stronger product.

Snap Furl CF-700 Furling System from SCHAEFER
" Small boat furler comparison, Practical SailorSnapFurl systems come in two sizes to accommodate boats 16' to 24' and boats 24' to 28' and represents the latest in quality Schaefer design and engineering. The efficient Round Geon™ PVC foil snaps quickly and easily around your boat’s existing headstay without the need for special tools or modifications to the rig. System SnapFurl CF-500 for Boats 16’ to 24’ (4. Long fiber reinforced injection molded components make SnapFurl CF 500 unique.

3/8" Bow/Stern Eye - 1.03" ID Between Studs x 4.63" Thread Length from SUNCOR
Bow / Stern Eye 304 Stainless Steel - Formed . Each U-Bolt set includes four nuts (two standard and two beveled) . Includes one bow plate, and one stern plate. . Threads are "UNC". . Stock size: 3/8" . ID between studs: 1. 03" . Thread length: 2. 50" .

300 Series Fairlead Block, Fixed Style, 2-7/32" x 3/4" from SCHAEFER
Same as the Schaefer 200 Series fairlead blocks, but with twice the working load. Use #10 fasteners. Configuration: Lead block. Sheave: UV-stabilized white Delrin®. Ball Bearings: Delrin. Sheave Size: 1-7/16" (37mm). Line Diameter: 7/16". Cheek Material/Finish: Polished stainless.

1/4" Dia. Stamped Halyard Shackle, 1,000SWL from SCHAEFER
Stamped Halyard Shackles haveflared heads with cross pin retainer for attachment to rope. Captive design prevents accidental opening Quick release pin #93-42 - 1/4" Shackle Pin dia. , 1/2" Inside Width, 1,000 SWL #93-45 - 5/16" Shackle Pin dia.