Top Sellers
Furler Kit for Boat Length to 16', 500lb. SWL, 1/8" Max. Wire dia., 1/4" Pin dia., 2-1/2" Pin-to-Pin, 5/32" Furling Line dia. from HARKEN
Furl or set your jib from your cockpit Harken small boat furlers allow the sail to be set and furled from the cockpit, a critical convenience in many racing dinghies and trailerable sailboats. Constructed of Hardkote anodized Teflon-impregnated aluminum, they feature multiple stacked races of Delrin or Torlon ball bearings for smooth rotation under load. The jib’s luff wire must be properly seized to the sail, since it carries most of the headstay load. 434 furler for dinghies under 16ft. (4.
|
Large Dinghy Snatch Block, 9/16" Line Dia., 40mm Sheave Dia., 1300 SWL from HOLT ALLEN
Glass-filled nylon cheeks with 316 stainless straps increase working efficiency more than 50% with minimal weight increase. Stainless ball bearings in a polypropylene cassette. For spinnaker sheet, jib sheet turning blocks, etc. Cheek Material/Finish: Glass filled nylon. Ball Bearing: Stainless ball bearings. Opening: Hinged cheek/axle.
|
PE-1 Lexan Mast Pad Eye from FORESPAR
For use on our small poles. 1-3/4"H x 1-1/4" x 5/8"dia. ring. Same ring as supplied with 4-8 and 6-12 poles.
|
60mm Racing Fiddle Block with Becket & Cleat, 882lb. SWL, 12.4oz. from LEWMAR
For chafe-free, low-friction tackles. Sheave: Anodized aluminum alloy . Ball Bearings: Delrin® . Sheave Size: 2-3/8" (60mm) & 1-5/8" (40mm) . Line Dia. : 3/8" max. . Cheek Material/Finish: Anodized aluminum alloy . Shackle/Strap Type: Swivel with three-way locking, drilled-out head . Cleat: Model with cleat: adjustable arm, aluminum cam cleat .
|
1-7/8" Polished Brass Flush Ring Pull from ABI
Highly polished brass . Convenient flush-fitting ring pull for cabinets, small doors, and hatches. . 1-7/8"L x 1-1/2"w . Requires four #5 fasteners .
|
CP Zinc Elbow Catch from PERKO
Chrome-plated zinc with stainless steel spring. . Measures: 1 1/8" x 9/16" . Requires #6 RH screws (Not included).
|
Acetal Thru-Transom Scupper from WEST MARINE
One-way rubber flapper valve and thru-hull fitting. For 1-1/2"ID hose. Overall length: 6-1/4". Installation hole size: 2". Max.
|
Flipper Pump from WHALE PUMPS
Easy back-and-forth action produces one-way discharge. Spout swivels. Made of nylon, aluminum and synthetic rubber. For 1/2"ID hose. Material: Nylon, aluminum, rubber . Capacity: 2gpm . Dimensions: 7-1/8"H x 6"dia. . Cutout Size: 2". Clearance: 4-1/2" .
|
4.5" Stainless-Steel Pop-Up “Neat Cleat” from ATTWOOD
Retractable stainless steel cleats retract to only 1/2" above deck and have direct drainage to the bilge. Corrosion-free. Install easily. Hardware included. Functions: Drains to bilge with drainage receptacle. Requires 3/8" ID tube (not supplied) . Material: Stainless steel . Height: Lowered, 1/2"; Raised, 1-5/8" . Line Size: 1-1/4" line opening . Cutout Size: 7/8" hole saw size. Max.
|
Waste Caddy from TODD ENTERPRISES
Todd Waste Caddy A portable 29-gal. capacity waste removal system. Moves easily on pneumatic tires with plastic bearings. Features a vented cap and 10-foot, 1-1/2"dia. hose and gravity-assisted pump that forces out fluid by gravity for a more rapid transfer. Spring-loaded nozzle eliminates leaks . Bronze ball valve is located at the bottom of the tank . Constructed of cross-linked polyethylene for strength and durability .
|
Trapeze & Vang Cleat from CLAMCLEAT
The cleat has an in-built pulley that offers a compact solution for rigging with a 1:1 or 2:1 advantage, where a quick, positive lock that is easy to release is required. The sailor's preferred choice for adjusting trapeze lines.
|
CP Zinc Sliding Window Stop from PERKO
Chrome-plated zinc with plastic cover on stopping plate. . Base measures 3/4"W x 1 7/8"L. . Requires #8 fasteners (not included). . Stopping plate length: 1 1/2'' . Made in U. S. A.
|
RailLight™ Clamp-On Solar-Powered Light from SIMPLY BRILLIANT
Solar-Powered Sol Lights™ RailLight™ charges all day and shines all night! Clamp this solar-powered portable light to any railing, coaming, stanchion, step, ladder or dock box for up to eight hours of light with just an eight hour charge of sunlight. Coated stainless steel finish resists corrosion. Comes with two clamps: one for round railings up to 1-1/4", and a transom clamp for up to 2" thickness. Dual 700mA rechargeable and replaceable NiCad batteries.
|
Gusher 10 Pump from WHALE PUMPS
Die-cast, epoxy-coated, anodized alloy, synthetic neoprene rubber diaphragm and stainless steel. Removable stainless handle with lanyard. To complete the installation, select either the Aluminum or Plastic Thru-Deck Kit, which seal the installation against water intrusion and and give it a finished look. Nitrile Diaphragm Kit, AK3714, available through special order. Material: Anodized aluminum . Dimensions: 8"H x 4-1/8"W x 5-3/4"L . Port Sizes: 1-1/2" .
|
Nauta 9 Gallon Flexible Fuel Tank from IMTRA CORPORATION
Flexible gasoline tanks won't rust, don't rattle, are easy to tie down, easy to carry, and won't scrape your boat. The Nauta 9-Gallon flexible fuel tank features comfortable, molded carrying handles and rugged 840-denier nylon construction. Fitted with a 1 1/2'' pivoting fill and a capped and 1/4'' NPT hose barb. Measures 28 1/2'' x 17 1/2'' x 6 1/2''.
|
|
1, 1-1, 16", 16" from SPINLOCK, 16" Line Dia, from LEWMAR, 8" from SPINLOCK
|
This site contains about 37,785 documents.
|
|
View by:
Title
|
Category
|
Manufacturer
|
Part No
|
Price
|
|
Page:
1
100
200
300
400
500
600
700
800
970
980
990
1,000
1,010
1,020
1,030
1,040
1,050
1,060
1,061
1,062
1,063
1,064
1,065
1,066
1,067
1,068
1,069
1,070
1,071
1,072
1,073
1,074
1,075
1,076
1,077
1,078
1,079
1,080
1,081
1,082
1,083
1,084
1,085
1,086
1,087
1,088
1,089
1,090
1,100
1,110
1,120
1,130
1,140
1,150
1,160
1,170
1,200
1,260
|
|
|
Home -> Sailboat -> Cleats & Stoppers -> Rope Clutches->Cam Replacement & Upgrade Kits for XTS Powerclutches
Cam Replacement & Upgrade Kits for XTS Powerclutches.
Part No: CAM-0814
|
|
|
|
|
Home -> Sailboat -> Cleats & Stoppers -> Rope Clutches->Cam Replacement & Upgrade Kits for XTS Powerclutches
Cam Replacement & Upgrade Kits for XTS Powerclutches.
Part No: CAM-0608
|
|
|
|
|
Home -> Sailboat -> Cleats & Stoppers -> Rope Clutches->Cam Replacement & Upgrade Kits for XTS Powerclutches
Cam Replacement & Upgrade Kits for XTS Powerclutches.
Part No: XTS-SMNT
|
|
|
|
Home -> Sailboat -> Cleats & Stoppers -> Rope Clutches->D2 Rope Clutches
Allows controlled release under loadThe award winning D2 Rope Clutch, built for big boat applications, allows for an easy and controlled release even at full holding power. Instead of just jamming the rope, the D2 clutch's Domino Cluster mechanism has a longer holding pattern for better grip and less rope wear. Fits line sizes from 5/16" (8mm) to 9/16" (14mm). Application: High load applications on boats to 55', low load and control lines on larger boats . Safe Working Load: 2650lb.
Part No: 29101410
|
|
|
|
|
Home -> Sailboat -> Cleats & Stoppers -> Rope Clutches->D2 Rope Clutches
Allows controlled release under loadThe award winning D2 Rope Clutch, built for big boat applications, allows for an easy and controlled release even at full holding power. Instead of just jamming the rope, the D2 clutch's Domino Cluster mechanism has a longer holding pattern for better grip and less rope wear. Fits line sizes from 5/16" (8mm) to 9/16" (14mm). Application: High load applications on boats to 55', low load and control lines on larger boats . Safe Working Load: 2650lb.
Part No: 29101414
|
|
|
|
|
Home -> Sailboat -> Cleats & Stoppers -> Rope Clutches->D2 Rope Clutches
Allows controlled release under loadThe award winning D2 Rope Clutch, built for big boat applications, allows for an easy and controlled release even at full holding power. Instead of just jamming the rope, the D2 clutch's Domino Cluster mechanism has a longer holding pattern for better grip and less rope wear. Fits line sizes from 5/16" (8mm) to 9/16" (14mm). Application: High load applications on boats to 55', low load and control lines on larger boats . Safe Working Load: 2650lb.
Part No: 29101412
|
|
|
|
|
Home -> Sailboat -> Cleats & Stoppers -> Rope Clutches->D2 Rope Clutches
Allows controlled release under loadThe award winning D2 Rope Clutch, built for big boat applications, allows for an easy and controlled release even at full holding power. Instead of just jamming the rope, the D2 clutch's Domino Cluster mechanism has a longer holding pattern for better grip and less rope wear. Fits line sizes from 5/16" (8mm) to 9/16" (14mm). Application: High load applications on boats to 55', low load and control lines on larger boats . Safe Working Load: 2650lb.
Part No: 29103412
|
|
|
|
|
Home -> Sailboat -> Cleats & Stoppers -> Rope Clutches->D2 Rope Clutches
Allows controlled release under loadThe award winning D2 Rope Clutch, built for big boat applications, allows for an easy and controlled release even at full holding power. Instead of just jamming the rope, the D2 clutch's Domino Cluster mechanism has a longer holding pattern for better grip and less rope wear. Fits line sizes from 5/16" (8mm) to 9/16" (14mm). Application: High load applications on boats to 55', low load and control lines on larger boats . Safe Working Load: 2650lb.
Part No: 29103414
|
|
|
|
|
Home -> Sailboat -> Cleats & Stoppers -> Rope Clutches->D2 Rope Clutches
Allows controlled release under loadThe award winning D2 Rope Clutch, built for big boat applications, allows for an easy and controlled release even at full holding power. Instead of just jamming the rope, the D2 clutch's Domino Cluster mechanism has a longer holding pattern for better grip and less rope wear. Fits line sizes from 5/16" (8mm) to 9/16" (14mm). Application: High load applications on boats to 55', low load and control lines on larger boats . Safe Working Load: 2650lb.
Part No: 29102410
|
|
|
|
|
Home -> Sailboat -> Cleats & Stoppers -> Rope Clutches->D2 Rope Clutches
Allows controlled release under loadThe award winning D2 Rope Clutch, built for big boat applications, allows for an easy and controlled release even at full holding power. Instead of just jamming the rope, the D2 clutch's Domino Cluster mechanism has a longer holding pattern for better grip and less rope wear. Fits line sizes from 5/16" (8mm) to 9/16" (14mm). Application: High load applications on boats to 55', low load and control lines on larger boats . Safe Working Load: 2650lb.
Part No: 29102414
|
|
|
|
Home -> Sailboat -> Cleats & Stoppers -> Rope Clutches->Midrail Cleats
Reduce deck clutter, tie spring lines, fenders, dinghies, etc. onto this moveable, low-profile, heavy-duty cleat. The spring-loaded cleat fits on 1 1/4'' T-track, so you can make quick and easy position changes without tools. Made of corrosion-resistant, polished, investment cast 316 stainless. Strong, adjustable cleat can also be used as a chock. To install, simply remove track end stop, slide on the cleat and lock into desired position.
Part No: 70-74
|
|
|
|
Home -> Sailboat -> Cleats & Stoppers -> Rope Clutches->XAS Powerclutches
Positive one-way locking clutches for easy release and relocking Reliable, lightweight, and powerful enough to handle high loads with outstanding line control. Features improved lever action, soft-feel handles for comfort, excellent line gripping and improved release. Application: Racers up to 27' and cruisers up to 35' . Height: 2-3/4" (69mm) . Length: 5-3/16" (134mm) . Width: Single: 1-1/2" (39mm); Double: 2-9/16" (65mm); Triple: 3-5/8" (91mm) .
Part No: XAS0612/3
|
|
|
|
|
Home -> Sailboat -> Cleats & Stoppers -> Rope Clutches->XAS Powerclutches
Positive one-way locking clutches for easy release and relocking Reliable, lightweight, and powerful enough to handle high loads with outstanding line control. Features improved lever action, soft-feel handles for comfort, excellent line gripping and improved release. Application: Racers up to 27' and cruisers up to 35' . Height: 2-3/4" (69mm) . Length: 5-3/16" (134mm) . Width: Single: 1-1/2" (39mm); Double: 2-9/16" (65mm); Triple: 3-5/8" (91mm) .
Part No: XAS0612/1
|
|
|
|
|
Home -> Sailboat -> Cleats & Stoppers -> Rope Clutches->XAS Powerclutches
Positive one-way locking clutches for easy release and relocking Reliable, lightweight, and powerful enough to handle high loads with outstanding line control. Features improved lever action, soft-feel handles for comfort, excellent line gripping and improved release. Application: Racers up to 27' and cruisers up to 35' . Height: 2-3/4" (69mm) . Length: 5-3/16" (134mm) . Width: Single: 1-1/2" (39mm); Double: 2-9/16" (65mm); Triple: 3-5/8" (91mm) .
Part No: XAS0408/3
|
|
|
|
|
Home -> Sailboat -> Cleats & Stoppers -> Rope Clutches->XAS Powerclutches
Positive one-way locking clutches for easy release and relocking Reliable, lightweight, and powerful enough to handle high loads with outstanding line control. Features improved lever action, soft-feel handles for comfort, excellent line gripping and improved release. Application: Racers up to 27' and cruisers up to 35' . Height: 2-3/4" (69mm) . Length: 5-3/16" (134mm) . Width: Single: 1-1/2" (39mm); Double: 2-9/16" (65mm); Triple: 3-5/8" (91mm) .
Part No: XAS0408/2
|
|
|
|
|
Home -> Sailboat -> Cleats & Stoppers -> Rope Clutches->XAS Powerclutches
Positive one-way locking clutches for easy release and relocking Reliable, lightweight, and powerful enough to handle high loads with outstanding line control. Features improved lever action, soft-feel handles for comfort, excellent line gripping and improved release. Application: Racers up to 27' and cruisers up to 35' . Height: 2-3/4" (69mm) . Length: 5-3/16" (134mm) . Width: Single: 1-1/2" (39mm); Double: 2-9/16" (65mm); Triple: 3-5/8" (91mm) .
Part No: XAS0408/1
|
|
|
|
|
Home -> Sailboat -> Cleats & Stoppers -> Rope Clutches->XTS Powerclutches
Updated for performance with an advanced release mechanism, these clutches feature a concave/convex cam design for lines from 1/4" to 9/16". Extruded aluminum handles have a new soft end grip. Application: Identical footprint to XT series. Larger offshore and coastal racers and cruisers . Line Size: XTS0814: 5/16"–9/16"; XTS0608: 1/4"–5/16" . Height: 3-7/16" (85mm) . Fasteners: Two 5/16" (8mm) FHMS .
Part No: XTS0814/1
|
|
|
|
|
Home -> Sailboat -> Cleats & Stoppers -> Rope Clutches->XTS Powerclutches
Updated for performance with an advanced release mechanism, these clutches feature a concave/convex cam design for lines from 1/4" to 9/16". Extruded aluminum handles have a new soft end grip. Application: Identical footprint to XT series. Larger offshore and coastal racers and cruisers . Line Size: XTS0814: 5/16"–9/16"; XTS0608: 1/4"–5/16" . Height: 3-7/16" (85mm) . Fasteners: Two 5/16" (8mm) FHMS .
Part No: XTS0814/2
|
|
|
|
|
Home -> Sailboat -> Cleats & Stoppers -> Rope Clutches->XTS Powerclutches
Updated for performance with an advanced release mechanism, these clutches feature a concave/convex cam design for lines from 1/4" to 9/16". Extruded aluminum handles have a new soft end grip. Application: Identical footprint to XT series. Larger offshore and coastal racers and cruisers . Line Size: XTS0814: 5/16"–9/16"; XTS0608: 1/4"–5/16" . Height: 3-7/16" (85mm) . Fasteners: Two 5/16" (8mm) FHMS .
Part No: XTS0814/3
|
|
|
|
|
Home -> Sailboat -> Cleats & Stoppers -> Rope Clutches->XTS Powerclutches
Updated for performance with an advanced release mechanism, these clutches feature a concave/convex cam design for lines from 1/4" to 9/16". Extruded aluminum handles have a new soft end grip. Application: Identical footprint to XT series. Larger offshore and coastal racers and cruisers . Line Size: XTS0814: 5/16"–9/16"; XTS0608: 1/4"–5/16" . Height: 3-7/16" (85mm) . Fasteners: Two 5/16" (8mm) FHMS .
Part No: XTS0608/2
|
|
|
|
|
Home -> Sailboat -> Cleats & Stoppers -> Rope Clutches->XTS Powerclutches
Updated for performance with an advanced release mechanism, these clutches feature a concave/convex cam design for lines from 1/4" to 9/16". Extruded aluminum handles have a new soft end grip. Application: Identical footprint to XT series. Larger offshore and coastal racers and cruisers . Line Size: XTS0814: 5/16"–9/16"; XTS0608: 1/4"–5/16" . Height: 3-7/16" (85mm) . Fasteners: Two 5/16" (8mm) FHMS .
Part No: XTS0608/1
|
|
![4" Jam Cleat Open-Base Cleat, 5/16" Max. Line Dia., two #10 FHMS, 5/8"H from SCHAEFER]( "4\" Jam Cleat Open-Base Cleat, 5/16\" Max. Line Dia., two #10 FHMS, 5/8\"H from SCHAEFER")
|
|
Home -> Sailboat -> Cleats & Stoppers->Aluminum Cleats
These tough cleats are hardcote-anodized to provide strength and corrosion resistance for years of reliable service. Lightweight, strong aluminum offers an advantage over easily “burned out” plastic designs.
Part No: 70-78
|
|
|
|
Home -> Sailboat -> Cleats & Stoppers->Bronze and Chromed Zinc Cleats
We recommend stainless or bronze cleats for use in fresh or salt water. Zinc and Zamak cleats should be used in fresh water only. We stock a complete selection of cleats for anchoring, docking and general-purpose use.
Part No: 1353BR
|
|
|
|
Home -> Sailboat -> Cleats & Stoppers->Bulls Eye Fairlead/Cleat on Swivel Base
Low-profile bulls eye, swivel base, and cleat in one. Aluminum arm swivels through 360°, and supports a high performance T-Cleat with Fast Track fairlead. Bulls eye has stainless liner for long life.
Part No: RF67
|
|
|
|
|
Home -> Sailboat -> Cleats & Stoppers->Bulls Eye Fairlead/Cleat on Swivel Base
Low-profile bulls eye, swivel base, and cleat in one. Aluminum arm swivels through 360°, and supports a high performance T-Cleat with Fast Track fairlead. Bulls eye has stainless liner for long life.
Part No: RF58
|
|
|
|
Home -> Sailboat -> Cleats & Stoppers->Cam Bases
Swivels ride on two rows of ball bearings for smooth, effortless pivoting even under high loads. Use #144 and #205 for mainsheets on dinghies and small offshore boats. #144 has a tall arm for use with bigger blocks. The low-profile 205 is used at the deck level and when smaller blocks are used.
Part No: 144
|
|
|
|
|
Home -> Sailboat -> Cleats & Stoppers->Cam Bases
Swivels ride on two rows of ball bearings for smooth, effortless pivoting even under high loads. Use #144 and #205 for mainsheets on dinghies and small offshore boats. #144 has a tall arm for use with bigger blocks. The low-profile 205 is used at the deck level and when smaller blocks are used.
Part No: 241
|
|
|
|
|
Home -> Sailboat -> Cleats & Stoppers->Cam Bases
Swivels ride on two rows of ball bearings for smooth, effortless pivoting even under high loads. Use #144 and #205 for mainsheets on dinghies and small offshore boats. #144 has a tall arm for use with bigger blocks. The low-profile 205 is used at the deck level and when smaller blocks are used.
Part No: 238
|
|
|
|
|
Home -> Sailboat -> Cleats & Stoppers->Cam Bases
Swivels ride on two rows of ball bearings for smooth, effortless pivoting even under high loads. Use #144 and #205 for mainsheets on dinghies and small offshore boats. #144 has a tall arm for use with bigger blocks. The low-profile 205 is used at the deck level and when smaller blocks are used.
Part No: 240
|
|
|
|
|
Home -> Sailboat -> Cleats & Stoppers->Cam Bases
Swivels ride on two rows of ball bearings for smooth, effortless pivoting even under high loads. Use #144 and #205 for mainsheets on dinghies and small offshore boats. #144 has a tall arm for use with bigger blocks. The low-profile 205 is used at the deck level and when smaller blocks are used.
Part No: 205
|
|
|
