Roller Shaft Cap Nuts Only - 1/2", Pack of 8 from C E SMITH
Roller Size Length Shaft Diameter Shafts and Nuts 4" 5 1/4" 1/2" 4" 5 1/4" 5/8" 5" 6 1/4" 1/2" 5" 6 1/4" 5/8" 8" 9 1/4" 5/8" 10" 11 1/8" 5/8" 11" 12 3/4" 1/2" 12" 13 1/2" 5/8" Shaft Only 18" 19" 5/8" Cap Nuts Only Packs of 8.

Deck Fill, Gas, w/Key, 1-1/2" from WHITECAP INDUSTRIES
Stainless-steel deck fills with durable cast heads—not the thin stamped heads found on many imports. Gas, Diesel and Water fills have 1 1/2" openings. Waste fill has 2" opening. All connect to 1 1/2" hose, and include a stainless key. Material: Stainless . Attachment Method: 1 1/2" hose . Flange Diameter: 3" or 3 1/2" (waste) . Fasteners: Three #10 FHMS . Cutout Diameter: 1 5/8" .

Potable Water Holding Tank, 3 Gal. from TODD ENTERPRISES
1520) requirements. Standard Tanks feature a multiple port arrangement that enables use as a sanitation holding tank or for potable water storage. They include two 1 1/2" fill/drain ports and two 1/2" vent/supply ports. Designed for waste storage, each includes two 1 1/2" ports for inlet and drain and one 1/2" vent port. Both Standard and Heavy-Duty Tanks feature threaded NPT ports that are molded in to eliminate stress cracks and leaks. One year warranty.

Rim Latch Sets - Reverse Bevel with Flush Strike from PERKO
Chrome-plated zinc. Sliding lock button. Case size: 2 1/8'' x 1 3/4''. Escutcheon Size: 4 3/8'' x 1 1/4''. For Door: 5/8'' to 1 3/8''.

Solid Brass Vertical Action Galley Pump from FYNSPRAY
Vertical plunger pump with a gracefully arched spout. 50 strokes per gallon. 1"diameter tube. Fits 1/2"–5/8" hose. Requires 8 1/2" clearance below counter surface; 9 3/4" above Material: Brass. Capacity: 50 strokes/gal. Dimensions: 9 3/4"H. Cutout Size: 1 1/8". Clearance: 8 1/2".

Aft-Deck Shower System from ATTWOOD
This compact hot/cold shower stores neatly in its own compartment on the stern or in the head. Includes a handheld shower spray head with shutoff, 6' hose, hot/cold water controls and a cover. Easily hooked into your freshwater system. Compartment is drilled for six #8 fasteners. Material: High-impact plastic . Dimensions: 9-1/2"H x 5"W x 2-1/4"D . Hose Size: 6'L . Port Sizes: 1/2" NPT .

Stainless Boat Hook Holders from PERKO
Polished stainless steel holders for poles to 1. 5" dia. 3. 5" L x 1" W. . . Sold in pairs.

Panel Mount Thermal Circuit Breaker, 50A from BLUE SEA SYSTEMS
An economical solution for high amperage loads where dependability is required in marine environments. Waterproof and ignition-protected (conforming to SAE J1171) so these circuit breakers are safe for installation aboard gasoline-powered boats. Ideal for branch circuits, windlasses, inverters and watermakers. False-trip free—designed to trip when subjected to a fault current. Available in panel and surface mounts. Interrupt Rating: 3000A at 12V DC. Voltage Compatibility: 42V DC.

Furler Kit for Boat Length to 16', 500lb. SWL, 1/8" Max. Wire dia., 1/4" Pin dia., 2-1/2" Pin-to-Pin, 5/32" Furling Line dia. from HARKEN
Furl or set your jib from your cockpit Harken small boat furlers allow the sail to be set and furled from the cockpit, a critical convenience in many racing dinghies and trailerable sailboats. Constructed of Hardkote anodized Teflon-impregnated aluminum, they feature multiple stacked races of Delrin or Torlon ball bearings for smooth rotation under load. The jib’s luff wire must be properly seized to the sail, since it carries most of the headstay load. 434 furler for dinghies under 16ft. (4.

WL/1 Fairlead Model from SPINLOCK
New low-profile design easily mounts to 1" stanchion using internal clamping system. WL/2 sheave model utilizes unique tracker ball angle adjustment. WL/1 Fairlead model includes stainless-steel bullseye for strength.

Clamp-On Rod Holder - 1 1/4"ID Horizontal, Gold from WEST MARINE
1 1/4IN HORIZONTAL MOUNT.

Flex Trim - Black 1/2" opening from TACO PRODUCTS
For a beautiful finished look on unfinished edges. Just push it on and it's on to stay. Grips on difficult materials, compound curves, etc. Individual corrosion resistant aluminum clips for a permanent grip. Black or White . Sold in 25' lengths. . Available in four sizes:. 5/32" opening x 35/64"H. 1/4" opening x 1/2"H. 3/8" opening x 5/8"H.

1/4" - 5/16" Anchor connector from WEST MARINE
Cleaner than standard anchor shackles, an anchor connector pulls easily over bow roller. Attaches with an Allen wrench (Included) . High-grade galvanized steel . Safe Working Loads: 1/4" - 5/16" unit: 1,390lbs.

Off/1/All/2 Battery Switch, 380 Continuous Amps, 850 Intermittent Amps from PERKO
For high-amperage applications like diesel engine starters, large inverters and windlasses. Reinforced polycarbonate body, 1/2"dia. brass terminal connections and an alternator field disconnect. Alt. Field Disc. : Yes . Switch Material: Reinforced Polycarbonate. Terminal Material/Size: Brass 1/2"dia. . Switch Dimensions: 5-1/4"sq. x 3-3/8"H .

Flat Cam Riser, 1"H from HARKEN
Harken Cam-Matic cleats are legendary for smooth operation when holding and releasing control lines. Three rows of Delrin ball bearings allow the jaws to open and close smoothly under the highest loads. Light springs allow the cleats to open freely, so the teeth do not have to be sharp which means that your line lasts longer. Use models with aluminum jaws for high loads, or when the line will be drawn through the teeth for adjustment.