Solid Brass Vertical Action Galley Pump from FYNSPRAY
Vertical plunger pump with a gracefully arched spout. 50 strokes per gallon. 1"diameter tube. Fits 1/2"–5/8" hose. Requires 8 1/2" clearance below counter surface; 9 3/4" above Material: Brass. Capacity: 50 strokes/gal. Dimensions: 9 3/4"H. Cutout Size: 1 1/8". Clearance: 8 1/2".

PAR-Max 4 Water-System Pump, 12V from JABSCO
Flow rate: 16. 3 Litres/min (4. 3 gallons/min) Self-priming from dry up to 2. 4m (7. 8ft) Smooth flow. Dry running capability. Soft noise absorbing mounts. Snap-fit port fittings. Corrosion resistant materials. Meets USCG Regulation 183. 410 and ISO 8846 MARINE (ignition protection).

Three Position Ignition Switch, OFF-Ignition-Start Functions from COLE HERSEE
Two position is for engines with a separate starter pushbutton. Three position: Off/Ignition/Start. Four position: Accessory/ Off/Ignition/Start or Off/Run/Push to Choke/Battery-Start (magneto switch). Brass construction, 2 keys supplied. 13/16" dia. mounting hole.

Rounded Oval, 8-1/2"W x 11-1/4"L x 5-1/4"D, 1" Flange, 1-1/2" Drain from AMBASSADOR MARINE
Made from 304 stainless steel and mirror-polished to a deep luster, these sinks incorporate SoundKOTE Noise Reduction Technology to reduce the unpleasant clanging associated with many metal sinks. Flanges permit over- or under-the-counter mounting. Low-Profile 90° drains fit standard 1"ID hose and are slanted to maximize drainage.

Teak Bulkhead Molding - 2 1/4" Radius, Inside Corner, 5/8"H x 71 3/16"W with 3/4" Gap from SEATEAK
Assorted Teak Finish Trim Moldings.

G. O'Day 222/Santana 525,Length 47", Height at tip 2 1/4", Width at butt 1 1/2", Width at tip 2" from WEST MARINE
Replace that old ugly tiller with a new hand-made laminated ash and mahogany wood tiller, made to fit your rudder hardware, and pre-finished with multiple coats of premium marine spar varnish. Choose the right length and profile, and the butt-end measurements to fit your rudderhead hardware. Can’t find a good fit? Idasailor Marine can custom-build a tiller to your measurements . Custom tillers are shipped direct within 10 days . Click HERE to open the PDF custom order form.

Series 250 Exhaust Hose, 7/8"ID, 1-3/16"OD, 565psi Burst Pressure from SHIELDS RUBBER
For use in all marine water and wet-exhaust applications. Also for marine wet-exhaust where connection requires great length (greater than 4 x ID) or significant bend. Meets or exceeds standards for certified wet-exhaust hose. Sold by the foot with a maximum continuous length of 10' except where preceded by an asterisk, which indicates a maximum continuous length of 50'. Construction: Black synthetic rubber with wire helix and HD synthetic cord . Temperature Range: –20° to 200° F .

500gph 12V Bilge Pump, 3/4" Port, 1.9A Draw, 2.5A Fuse, 3-1/2"H x 2-3/8"W from RULE INDUSTRIES
Tough and reliable at a value price Great performance at a value price, Rule submersible pumps are the first choice for many boat manufacturers. Their motors feature stainless-steel shafts, water cooling and a vibration-free centrifugal impeller that won’t burn out if run dry. Strainer bases can easily be snapped off for cleaning. Each pump requires a panel switch for manual operation or a float switch for automatic operation. Select from 12V, 24V and 32V models. Can run dry without damage.

8mm (5/16") Stock Dia. Bolt, 4-5/16"L, 5/8" Hole Dia., 3" Stock Length, 1" Plate Dia. from SEADOG
Machined from 304 stainless steel.

Barbed Hose Reducer, 1/4" to 1/2" from SEAFIT
Nylon Hose Reducers, Barbed.

5/8" Clevis Pin dia., 1-3/16" inside dia., 4-pack from WEST MARINE
Stainless-Steel Cotter Rings.

"D" Shackle, 3/16" Pin Dia., 7/16" Inside Width, 1/2" Inside Length, 2500lb. Breaking Strength from HARKEN
Stainless-steel, high-resistance "D" shackles.

800gph Tsunami Bilge Pump, 2.5A @ 12V DC Draw, 3/4" Port, 4-3/8"H x 3-1/2"W from ATTWOOD
Versatile Tsunami pumps feature interchangeable, twist-and-lock cartridges that reduce maintenance time. All wires are caulked and tinned to prevent water wicking. Rugged glass and mineral-filled polymer construction resists chemicals, fuel and detergents and the compact, low-profile design eases installation in tight spaces.

Deck Plate, 3-3/8"dia. x 1-15/16"H, 2,250lb. SWL from SCHAEFER
Swivel base for deck mounting blocks.

Flex Trim - Black 1/2" opening from TACO PRODUCTS
For a beautiful finished look on unfinished edges. Just push it on and it's on to stay. Grips on difficult materials, compound curves, etc. Individual corrosion resistant aluminum clips for a permanent grip. Black or White . Sold in 25' lengths. . Available in four sizes:. 5/32" opening x 35/64"H. 1/4" opening x 1/2"H. 3/8" opening x 5/8"H.