2" ID, 90° Marine Rubber Exhaust Elbow from SHIELDS RUBBER
Exhaust hose elbows let your wet-exhaust line make tight turns without kinking. They provide excellent tolerance to engine heat, vibration and back pressure. Install over rigid tubing or pipe using the four included stainless T-bolt clamps (two at each end). Not intended for hose-to-hose connections. Lubricate with water or detergent. 250°F max.

5" ID, 45° Marine Rubber Exhaust Elbow from SHIELDS RUBBER
Exhaust hose elbows let your wet-exhaust line make tight turns without kinking. They provide excellent tolerance to engine heat, vibration and back pressure. Install over rigid tubing or pipe using the four included stainless T-bolt clamps (two at each end). Not intended for hose-to-hose connections. Lubricate with water or detergent. 250°F max.

Series 250 Exhaust Hose, 2-3/8"ID, 2-3/4"OD, 230psi Burst Pressure from SHIELDS RUBBER
For use in all marine water and wet-exhaust applications. Also for marine wet-exhaust where connection requires great length (greater than 4 x ID) or significant bend. Meets or exceeds standards for certified wet-exhaust hose. Sold by the foot with a maximum continuous length of 10' except where preceded by an asterisk, which indicates a maximum continuous length of 50'. Construction: Black synthetic rubber with wire helix and HD synthetic cord . Temperature Range: –20° to 200° F .

Series 250 Exhaust Hose, 7/8"ID, 1-3/16"OD, 565psi Burst Pressure from SHIELDS RUBBER
For use in all marine water and wet-exhaust applications. Also for marine wet-exhaust where connection requires great length (greater than 4 x ID) or significant bend. Meets or exceeds standards for certified wet-exhaust hose. Sold by the foot with a maximum continuous length of 10' except where preceded by an asterisk, which indicates a maximum continuous length of 50'. Construction: Black synthetic rubber with wire helix and HD synthetic cord . Temperature Range: –20° to 200° F .

Rubrail Insert - for Style #6, Model 341100 from TACO PRODUCTS
Rubber inserts add cushioning to your aluminum rubrails. . These fit styles #5, #6 and #7. Rub rails and inserts sold separately. .

Insert - for Taco #V21-9517, #V21-9501, #V21-9602, Per Foot from TACO PRODUCTS
Rubber inserts add cushioning to your aluminum rubrails. . These fit styles #5, #6 and #7. Rub rails and inserts sold separately. .

#57 Vinyl & Rubber Cleaner/Conditioner - Pint from MEGUIARS
Cleans and protects your vinyl and rubberSpray on to remove ground-in dirt from soiled vinyl, rubber and plastic. Screens out damaging UV rays that can dry out and crack the surface. 16oz. 16oz.

Low-Permeation Fuel Hose, 1/2" ID, 250' Max. Length from SHIELDS RUBBER
Special design NBR tube with an embedded plastic barrier layer limits permeation. The design of this hose provides easy coupling insertion and the NBR/PVC cover is weather and UV resistant. The hose is also polyester reinforced and fire-resistant. Fuel Type: Fuel feed (gasoline up to 85% ethanol blended fuels/diesel/bio-diesel all blends) . Approvals: SAE J1527 Type A1-15 and ISO 7840 Type A1 . Construction: Reinforced with high strength synthetics to resist gasoline/alcohol permeation .

Series 315 Outboard Fuel Hose - 3/8"ID from SHIELDS RUBBER
Premium-quality fuel hose designed for outboard feed and vent lines. Remains flexible at low temperatures and resists UV sunlight. Silverado 2000 complies with SAE J1527 Type B2 specifications. Should not be used in applications requiring the use of Type B1 fuel feed line.

Series 150 Clear PVC Tubing, 1/2"ID, 45psi Burst Pressure from SHIELDS RUBBER
Single layer, nontoxic, FDA-approved clear vinyl tubing. Ideal for drain lines, iceboxes, refrigerators, livewells, bilge pump discharge, freshwater lines, water and holding tank vents. Sold per foot: 50’ maximum continuous length for 1/4" and 3/8" hose; 100' maximum continuous length for 1/2" hose and larger. Application: Non-pressurized water system supply; sink, shower, and icebox drains. Material: FDA formula vinyl. Reinforcement: None. Temperature Range: N/A.

Tee Type Sanitation Hose Fitting, Slip Fitting Thread from SHIELDS RUBBER
Fiberglass-reinforced nylon fittings designed to fit Shields Series 101, 148 and 144 hoses without heating or special tools. Use in sanitation systems, deck drain systems and water tank fill.

Wincher, 2.25IN TO 2.75IN from WATSKI
Winchers are rubber disks that fit over the top of your non-self-tailing winches to make them perform like self-tailers. Loading up the winch drums until the line contacts the underside of the Wincher creates friction which allows the line to self-tail. A rope groove holds line reasonably securely around the top of the winch. Practical Sailor Magazine suggests Winchers for halyard winches, but not sheet winches, although we have many comments from customers who swear by them.

84”L Fiberglass Bow from TAYLOR
Bows moounted in bow sockets are the sure and easy way to keep a boat cover taut and free from water-collecting pockets. Sockets can be mounted on any rail system or anywhere on deck wall. Rubber gasket provides snug fit for fiberglass bows. Super strong and flexible, will not take a “set”. Cut to desired length. Incude rubber end covers to grab socket.

Windshield Screw Cover Foam, 5/8"H x 1-1/4"W x 8'L from TACO PRODUCTS
Easy do-it-yourself solution for door, windshield or hatch leaks. Specially formulated sponge rubber is engineered to withstand corrosive environments. Windshield Screw Cover Foam gives your windshield a finished look.

Aquatech Boots, Black, 7 from GILL
2mm double-lined neoprene boots are idea for dinghy and small boat performance sailing and offer protection and secure footing in demanding conditions. They feature a wraparound, non- marking natural rubber sole for improved grip, flatlocked seams for comfort and an adjustable strap for maximum support. .