Sail Needles from BAINBRIDGE INTL
Sail Needles. Package of 7 assorted needles including 2 curved needles.

5/16" Wire Rope Clamp from SEADOG
Investment Cast 316 Stainless Body / AISI 304 Stainless U-Bolt. Accepts 5/16" wire. 1-5/8" Long. 1-3/8" wide.

Gasket (2) from SIERRA
Package of 2.

#810 Fillable Caulking Tubes from WEST SYSTEM
These applicators are great for injecting large amounts of epoxy, laying a lengthy bead of epoxy or making fillets. Large-volume applicators for use with a standard caulking gun. . Suitable for refilling during continuous use. Should be disposed of after epoxy cures. . Holds approximately 10 fl. oz. . Package of 2.

Furler Kit for Boat Length to 16', 500lb. SWL, 1/8" Max. Wire dia., 1/4" Pin dia., 2-1/2" Pin-to-Pin, 5/32" Furling Line dia. from HARKEN
Furl or set your jib from your cockpit Harken small boat furlers allow the sail to be set and furled from the cockpit, a critical convenience in many racing dinghies and trailerable sailboats. Constructed of Hardkote anodized Teflon-impregnated aluminum, they feature multiple stacked races of Delrin or Torlon ball bearings for smooth rotation under load. The jib’s luff wire must be properly seized to the sail, since it carries most of the headstay load. 434 furler for dinghies under 16ft. (4.

T-Ball Swage Fitting, 1/8" Wire Size from ALEXANDER-ROBERTS
Electropolished 316 stainless steel. Running Back style has a stainless bail rather than a swage end, to accept Dyneema or other rope for a running backstay. *Running Back style has a stainless bail rather than a swage end to accept Spectra or other rope for a running backstay. Style: Swage . Material: Electropolished Type 316 stainless steel . Configuration: T-ball swage .

Stainless-Steel “S” Hook, 3/16" Wire Dia., 5/8" Inside Width from SEAFIT
Stainless Steel "S" Hooks. Polished Stainless Steel Made in the U. S. A.

316 Stainless-Steel Hose Clamp, 7/16" to 11/16", SAE Size 3 from ABA OF AMERICA
Hose clamps you can trust now and later Trust these clamps for secure hose connections. All components are Type 316 stainless steel for ultimate corrosion resistance. The smooth, unperforated band surface and rolled edges prevent hose damage. Band and screw threads are properly pitched, rendering the clamp virtually immune to vibration-caused back-off. Hoses are measured by inside diameter, so use a clamp with a maximum opening at least a 1/4" larger .

Whale Gulper 220 Pump, 12V DC, Draw: 2.4A from WHALE PUMPS
Use this 3. Large 3/4" inlet and outlet valves are cut at 45° angles to minimize flow restriction. Ports rotate to the position you need to facilitate hose connections and it mounts vertically or horizontally—making installation a snap! It can run dry for extended periods without burnout and boasts a large diaphragm that generates up to 13' of lift. Rubber mounting feet reduce noise. Features: Will run dry without damage and pump a mixture of air and water . Large single diaphragm .

F8B-9 Direct Bolt-On Engine Cooling Pump, Detroit Diesel OEM from JOHNSON PUMPS
Used by premier marine engine manufacturers including Volvo Penta, Westerbeke, Yanmar and MAN, Johnson Pump is a leading provider of cooling pumps to OEMs worldwide. The pumps feature bronze housings, flexible impellers and different port sizes that satisfy a variety of cooling needs with flows between 3 and 165 g. p. m.

Series 60 Orbit Block, Single Light-Load, 2-3/8" Sheave Size, 1,710lb. SWL, 4.7oz. from RONSTAN
These exceptionally strong blocks feature the performance Orbit sheave with captive Acetal ball bearings for side thrust loads, eliminating the need for side retainer plates. The 75mm webbing block (RF79107) can be used where swivel head and shackle attachment is not required to achieve further weight savings. Sheave Size: 2-3/8" (60mm) or 3" (75mm). Line Diameter: Series 60: 1/2" (12mm), Series 75: 9/16" (14mm). Cheek Material/Finish: Anodized aluminum.

13-1/4" x 17" Propeller for Evinrude/Johnson Outboards from MERCURY MARINE
Three-blade aluminum one-piece propellers for Evinrude/Johnson outboards. 8–15hp, 9. 9–15hp 2–stroke 1974 & up, 8/9. 9/15hp 4–stroke 1995 & up: Model 5026695. 20–35hp, 20hp 1984–97, 25/30hp 1984 & up, 35hp 1976 & up: Models 4744207, 8640492. 40–75hp, 40hp 1984 & up, 65hp 1980–85, 48hp 1987–96, 75hp 1975–85, 50hp 1975 & up, Sprint 1986–92, 55hp 1976–79, Formula E 1986–92, 60hp 1980–85: Models 8640484, 4744173, 4744181. 45–75hp large gearcase, OMC Cobra 2. 3–2.

12-1/4" x 15" Propeller for Evinrude/Johnson Outboards from MERCURY MARINE
Three-blade aluminum one-piece propellers for Evinrude/Johnson outboards. 8–15hp, 9. 9–15hp 2–stroke 1974 & up, 8/9. 9/15hp 4–stroke 1995 & up: Model 5026695. 20–35hp, 20hp 1984–97, 25/30hp 1984 & up, 35hp 1976 & up: Models 4744207, 8640492. 40–75hp, 40hp 1984 & up, 65hp 1980–85, 48hp 1987–96, 75hp 1975–85, 50hp 1975 & up, Sprint 1986–92, 55hp 1976–79, Formula E 1986–92, 60hp 1980–85: Models 8640484, 4744173, 4744181. 45–75hp large gearcase, OMC Cobra 2. 3–2.

10" x 13" Propeller for Evinrude/Johnson Outboards from MERCURY MARINE
Three-blade aluminum one-piece propellers for Evinrude/Johnson outboards. 8–15hp, 9. 9–15hp 2–stroke 1974 & up, 8/9. 9/15hp 4–stroke 1995 & up: Model 5026695. 20–35hp, 20hp 1984–97, 25/30hp 1984 & up, 35hp 1976 & up: Models 4744207, 8640492. 40–75hp, 40hp 1984 & up, 65hp 1980–85, 48hp 1987–96, 75hp 1975–85, 50hp 1975 & up, Sprint 1986–92, 55hp 1976–79, Formula E 1986–92, 60hp 1980–85: Models 8640484, 4744173, 4744181. 45–75hp large gearcase, OMC Cobra 2. 3–2.

Small Boat Clevis Pin Kit from JOHNSON, C.S.
Assorted sizes of stainless-steel clevis and cotter pins. Small Boat kit contains 46 pieces ranging from 3/16"–5/16".