CARB GASKET KIT from SIERRA
Sierra carb kits and gaskets for engine tune ups.

Yamaha Carb Kit from SIERRA
Sierra carb kits and gaskets for engine tune ups.

Replaces OMC P/N 378444 from SIERRA
Many of Sierra's solenoids are manufactured by our Independence, KS plant. We produce both starter solenoids and continuous duty solenoids for trim and tilt pumps. Our features add up to solenoids which offer maximum magnetic plunger pull, reduced voltage drop and maximum corrosion protection.

Impeller, 18-3062 from SIERRA
Recommended replacement schedule is every 3 years for fresh water and every year for salt water Click to view a Sierra Impeller Application Chart (PDF) For further assistance, have your year & model information handy and call our Product Advisors at 1-800-BOATING.

For Chrysler/Force, 89-817109A2 from SIERRA
Many of Sierra's solenoids are manufactured by our Independence, KS plant. We produce both starter solenoids and continuous duty solenoids for trim and tilt pumps. Our features add up to solenoids which offer maximum magnetic plunger pull, reduced voltage drop and maximum corrosion protection.

Hot Foot Throttle Omc/Merc from T-H MARINE
Replaces your hand throttle with a foot pedal that makes you feel like you're behind the wheel of your automobile. When released, the Hot Foot automatically returns your engine to the idle position thanks to a strong stainless spring. Mounts directly to the deck of the boat and uses standard control cables. Aluminum pedal. Stainless hardware. Non-stick bearing surfaces.

Snap-On Cable Cover, 1/4" Wire Dia. from DAVIS INSTRUMENTS
White vinyl cable covers in 6' lengths. Tubes split down length and install in seconds.

33C Red Jacket Cable, 18' from TELEFLEX
The most widely used cable type in the world. 8" minimum bend radius. Cable adapter kits available for use with Mercury, MerCruiser, Johnson/ Evinrude, and OMC sterndrive. 3" travel.

4300BC TFX Cable - 20' from TELEFLEX
TfXtreme's unique design assures smoothness and efficiency–with hardly any lost motion–even in the longest and most complex cable routings! This means superior feel at the control, in any boat–performance that had been considered "impossible". TfXtreme achieves the "impossible". Patent-pending splined core to achieves the impossible–easy movement and minimum lost motion.

Sierra-Tube-Exhaust from SIERRA
Some larger V-8 engines that create a large amount of back pressure use exhaust tubes rather than bellows. This helps to relieve the excessive pressure and eliminate problems with premature bellows failure. In the past, the exhaust bellows would blow up like a balloon and cause the drive shaft bellows to rub against the yoke and U-joints causing holes in the bellows.

Hatch Riser Arm for 20" x 20" Hatch from TAYLOR
Replacement arms for Taylor hatches from 1987 to the present. Universal arms can be left or right.

10 Micron Replacement Filter Element for OMC 502905 from SIERRA
High-performance fuel injected engines require ultimate fuel filtration, separation of water from the fuel supply and maximum fuel flow. Sierra’s new filter elements deliver all three of these critical performance factors. 7900-Series 10 micron filters eliminate harmful contaminants at over 90% efficiency, while removing over 99% of emulsified water. Today’s ethanol-blended fuels increase the chances of water in fuel tanks, resulting in premature wear, poor performance and component damage.

10mm Ball Stud pair from TAYLOR
Taylor 10mm Ball Stud pair.

Water Circulating Pump - #18-3581 - Chrysler Inbd # 3004886, 3619542, 3619859, 3745985 from SIERRA
Water Pumps The water pump is the heart of your inboard or I/O cooling system. All Sierra pumps are bidirectional and can be installed on reverse rotation engines. The pumps are also powder coated for additional protection. Includes mounting gasket. Pumps include brass bi-directional impellers, brass plugs and fittings, carbon resin seal, all mounting gaskets, stainless steel seal cup and spring, stainless steel back plate (where required), and powder coating for maximum corrosion protection.

Johnson/Evinrude Outboard Starter, 120 to 140hp V4 (1985-99), 10 tooth drive gear from SIERRA
Sierra's new and remanufactured starters are the only marine starters that meet Marine UL standards. Sierra's remanufactured starters all have new solenoids, drives, bushings, brushes and springs. The bodies are powder coated for greater corrosion resistance. Sierra has entered an agreement with United Technologies to market their complete line of outboard starters and components. All are 100% load tested . Our remanufactured starters are covered by Sierra's customer satisfaction warranty .