Top Sellers
|
|
Whale Swim 'N' Rinse Transom Shower from WHALE PUMPS
Whale Swim 'N' Rinse Transom Shower Add the convenience of a hot and cold shower to your transom. The easy-to-install shower connects directly to the Whale Quick Connect 15 mm freshwater system. Durable, ABS plastic housing with cover hides the shower when not in use. 7' retracting hose . Water conservation control on the handset . Base plate: 6-1/2" x 11-1/2" . Allow 3-1/2" behind surface .
|
Flex Trim - Black 1/2" opening from TACO PRODUCTS
For a beautiful finished look on unfinished edges. Just push it on and it's on to stay. Grips on difficult materials, compound curves, etc. Individual corrosion resistant aluminum clips for a permanent grip. Black or White . Sold in 25' lengths. . Available in four sizes:. 5/32" opening x 35/64"H. 1/4" opening x 1/2"H. 3/8" opening x 5/8"H.
|
Hose Adapter, From 1-1/8" to 3/4"-5/8" from RULE INDUSTRIES
#69 is stepped & adapts from 1-1/8" to 3/4" - 5/8" #57 is an elbow & adapts from 1-1/8" to 1" NPT #67 adapts from 1-1/2" to 1-1/8".
|
Series 150 Clear PVC Tubing, 1/2"ID, 45psi Burst Pressure from SHIELDS RUBBER
Single layer, nontoxic, FDA-approved clear vinyl tubing. Ideal for drain lines, iceboxes, refrigerators, livewells, bilge pump discharge, freshwater lines, water and holding tank vents. Sold per foot: 50’ maximum continuous length for 1/4" and 3/8" hose; 100' maximum continuous length for 1/2" hose and larger. Application: Non-pressurized water system supply; sink, shower, and icebox drains. Material: FDA formula vinyl. Reinforcement: None. Temperature Range: N/A.
|
Roller Shaft Cap Nuts Only - 1/2", Pack of 8 from C E SMITH
Roller Size Length Shaft Diameter Shafts and Nuts 4" 5 1/4" 1/2" 4" 5 1/4" 5/8" 5" 6 1/4" 1/2" 5" 6 1/4" 5/8" 8" 9 1/4" 5/8" 10" 11 1/8" 5/8" 11" 12 3/4" 1/2" 12" 13 1/2" 5/8" Shaft Only 18" 19" 5/8" Cap Nuts Only Packs of 8.
|
500 RC Windlass, 600lb. Max. Pull, Boat Length 35', 1/4"HT Chain, 1/2" Rope Rode Size, 62'–Chain; 45'–Rope Speed Up/Min., 60' Speed Down/Min., 60A–75A @12V Draw from MAXWELL
These low-profile windlasses feature a patented tension system that maintains resistance required to feed chain/rope rode into the locker instead of jamming it in the windlass. Designed for easy installation, the motor can be oriented in any of 12 positions below decks. Two pieces bolt together quickly. Gasketed, watertight base. For decks to 2 3/4" thick. Capstan models and extra-long shafts for thick decks are available by Special Order. Style: Vertical . Rode Type: Rope/chain .
|
Rule-A-Matic Plus Float Switch from RULE INDUSTRIES
Is the float switch working? It's easy to check! Features a Rule-A-Matic float switch and an impact-resistant cover to protect against debris and jamming. Wiring is "blocked" by a rubber grommet to provide strain relief. Includes a convenient feature for manual tests. Activation Method: Float with mechanical contacts. Dimensions: 2-3/4"H x 2-1/2"W x 4-7/8"L. Capacity: 20A @ 12/24/32V DC.
|
Gunnel Guard - 1/2" Round, 1-1/2" Diameter, 20' Length from TAYLOR
These polyester-covered guards will protect your boat from dings and scratches and they won’t rot in the sun or saltwater like cotton guards. Great for use on dinghies and swim platforms, too. Fabric tabs attach easily with screws or nails. Half Round is for flat surfaces; 3/4 Round is for 90° edges. Sold in 10' or 20' lengths or by the foot up to 50'. Material: Polyester fabric/closed-cell foam . Attachment Method: Screws or nails . Shock Absorption Mechanism: Foam padding .
|
|
|
Scotch General Painting Masking Tape #2050 - 2" from 3M PRODUCTS
Use in a wide range of painting applicationsGeneral-purpose. Not for critical or extended outdoor use. Recommended Usage: General purpose masking or binding tape; adheres to previously painted or varnished surfaces . Material: Crepe paper with rubber resin adhesive . Removal Time: Three days .
|
1/4" Dia. Stamped Halyard Shackle, 1,000SWL from SCHAEFER
Stamped Halyard Shackles haveflared heads with cross pin retainer for attachment to rope. Captive design prevents accidental opening Quick release pin #93-42 - 1/4" Shackle Pin dia. , 1/2" Inside Width, 1,000 SWL #93-45 - 5/16" Shackle Pin dia.
|
Off/1/All/2 Battery Switch, 380 Continuous Amps, 850 Intermittent Amps from PERKO
For high-amperage applications like diesel engine starters, large inverters and windlasses. Reinforced polycarbonate body, 1/2"dia. brass terminal connections and an alternator field disconnect. Alt. Field Disc. : Yes . Switch Material: Reinforced Polycarbonate. Terminal Material/Size: Brass 1/2"dia. . Switch Dimensions: 5-1/4"sq. x 3-3/8"H .
|
PE-1 Lexan Mast Pad Eye from FORESPAR
For use on our small poles. 1-3/4"H x 1-1/4" x 5/8"dia. ring. Same ring as supplied with 4-8 and 6-12 poles.
|
|
|
|
from HARKEN, from SCHAEFER, 1, 1 1, 2'' from SEADOG, ¾'' from SEADOG
|
|
1 1/8" & 1 1/2" Outrigger Holders and Replacement Tubes.
Part No: 88503
|
|
|
|
|
1 1/8" & 1 1/2" Outrigger Holders and Replacement Tubes.
Part No: 99M 88504
|
|
|
|
|
1 1/8" & 1 1/2" Outrigger Holders and Replacement Tubes.
Part No: 88508
|
|
|
|
|
1 1/8" & 1 1/2" Outrigger Holders and Replacement Tubes.
Part No: 88507
|
|
|
|
|
1 1/8" & 1 1/2" Outrigger Holders and Replacement Tubes.
Part No: 88500
|
|
|
|
|
1 1/8" & 1 1/2" Outrigger Holders and Replacement Tubes.
Part No: 99M 88505
|
|
|
|
ECO Fuel Can Spill-Proof Spout.
Part No: 99W 05459
|
|
|
|
The backing provides excellent shelling and tear resistance, thus increasing the life and performance of the disc.
Part No: 21797
|
|
|
|
Designed for bringing control lines over the forward edge of cabin houses, coamings or rails. Ball bearing sheaves provide low friction support for lines that need to be bridged or lifted for a clean lead. Open race ball bearings allow salt, dirt and debris to be easily flushed out. Single blocks. Maximum line dia: 1/2". Use #10 fasteners. Configuration: Over-the-top lead block. Ball Bearings: Delrin® . Sheave: 7/16" . Line Dia: 7/16" .
Part No: 706-40
|
|
|
|
Jabsco 37072-0092 Marine Designer Series and Quiet Flush Marine Toilet Pump Assembly Kit (12-Volt).
Part No: 37072-0092
|
|
|
|
Clear Cover Only for Marelon Water Strainer.
Part No: 920178
|
|
|
|
This high-pressure electric pump clips onto any 12V battery to provide 2. 1 psi at 11. 7 cu. ft. /min. 23" hose. Inflate or deflate any inflatable or boat with ease, precision and unmatched portability.
Part No: 99M MP-250WM
|
|
|
|
Meets American Boat and Yacht Council (ABYC) standards UL 1077 recognized, TUV certified, CE marked for Europe and CSA certified for Canada The industry standard circuit breaker for Blue Sea Systems electrical panels Combines switching and circuit protection into a single device Used as AC Main circuit protection "Trip Free" design cannot be held "ON" during fault current condition.
Part No: 7242
|
|
|
|
|
Meets American Boat and Yacht Council (ABYC) standards UL 1077 recognized, TUV certified, CE marked for Europe and CSA certified for Canada The industry standard circuit breaker for Blue Sea Systems electrical panels Combines switching and circuit protection into a single device Used as AC Main circuit protection "Trip Free" design cannot be held "ON" during fault current condition.
Part No: 7237
|
|
|
|
The original Harken block Used for main and jib sheets on course racing keelboats, scows and dinghies with large mains. Often used for spinnaker halyards and sheets on small offshore boats. Swivel blocks feature a three-way head system with a set screw. Blocks with cams feature adjustable cam arms and reversible cam cleats. Where applicable, blocks use #8 fasteners. Sheave: Delrin. Bearings: Delrin ball bearings. Sheave Size: 2-1/4" (57mm). Line Diameter: 7/16" max.
Part No: 019
|
|
|
|
These rocker switches come in several different configurations for panel mounting. Available in illuminated and non-illuminated models, they feature non-glare black matte plastic housings, bezel and actuator, brass screw or blade terminals, and gasket-sealed housings. Snap-in mounting in panels from 0. 093" (2. 36mm) to 0. 187" (4.
Part No: 99W M-58031-01-
|
|
![Activated Carbon Filter Cartridge from GENOVA PRODUCTS]( "Activated Carbon Filter Cartridge from GENOVA PRODUCTS")
|
|
Replacement filter cartridge for water filter.
Part No: C232
|
|
|
|
The Livewell Pump Debris Strainer attaches directly to any pickup tubes on Rule Livewell Pumps. Filters out trash and debris which could clog pump.
Part No: 73
|
|
|
|
Removable Davit Accessories.
Part No: 414
|
|
|
|
Carry-On Portable A/C 2-Speed Switch.
Part No: 1014
|
|
|
|
Joystick control directs lights of Guest models 22040A, 22041A, 22044 OR 22045.
Part No: 22208A
|
|
|
|
Spares for the Whale Gusher Titan bilge pumps, containing: Qty Containing 2 Nut 2 Screw 1 Top clamping ring 1 Bottom clamping ring 4 Circlip.
Part No: AS4407
|
|
|
|
Home -> Anchor & Docking -> Anchor Line & Dock Line
stainless ring used in our Anchor Float is available for those who wish to splice their own system together from components they already own.
Part No: 002.3 WM
|
|
|
|
Home -> Anchor & Docking -> Anchor Line & Dock Line
Easy to use, maintenance free, and much cheaper than a windlass! Simply place the anchor ring over your anchor line, attach the anchor ball, lower the ball overboard, and run a slow course 30-45 degrees away from the anchor. This will move the ball down the anchor line to the anchor, pulling it free, and floating it to the surface. Complete Kit Includes: Red 12" Dia. A-1 ball Stainless Steel Anchor ring 3/8" Dia. Nylon Line with stainless snap For boats up to 40' Made in U. S. A.
Part No: AR-1N-DP
|
|
|
|
Home -> Anchor & Docking -> Anchor Line & Dock Line
The easiest docking you've ever done! The 4' Stretch 'N Slide dock line stretches to 8' long and has 7 individual loops, so you'll always have the perfect length for easy tie up. Secures your boat to the dock in seconds.
Part No: SNS-B
|
|
|
|
Home -> Anchor & Docking -> Anchor Line & Dock Line -> Anchor Line Accessories->Anchor & Rode Bags
Anchor Bag Durable mesh bag provides a convenient and tangle-free place to store your anchor rode. A number of features add to the life of your rode and make it easier to deploy. The wide mouth is held open with an internal stainless steel ring, but closes easily with a drawstring. . Mesh ends dry quickly and a reinforced slit in the bottom allows the bitter end to be passed outside the bag for securing. Brass boat snap allows you to hang the bag and rode where they’re most convenient.
Part No: AB-018S
|
|
|
|
|
Home -> Anchor & Docking -> Anchor Line & Dock Line -> Anchor Line Accessories->Anchor & Rode Bags
Anchor Bag Durable mesh bag provides a convenient and tangle-free place to store your anchor rode. A number of features add to the life of your rode and make it easier to deploy. The wide mouth is held open with an internal stainless steel ring, but closes easily with a drawstring. . Mesh ends dry quickly and a reinforced slit in the bottom allows the bitter end to be passed outside the bag for securing. Brass boat snap allows you to hang the bag and rode where they’re most convenient.
Part No: AB-018L
|
|
|
|
Home -> Anchor & Docking -> Anchor Line & Dock Line -> Chafe Gear and Snubbers->Chafe Guards
Abrasion-resistant polyester is tough, yet supple enough to pass through chocks. 18''L guards include ties for attaching to your lines. . Guaranteed for 5 years against sun deterioration. . Sold in pairs.
Part No: CG58.18
|
|
|
|
Home -> Anchor & Docking -> Anchor Line & Dock Line -> Chafe Gear and Snubbers->Leather Chafe Guards
The traditional chafe protection that many still prefer. If sleeve is to be placed over tail of eye splice, order one size larger than line diameter. Includes: 2 pre-punched 10"L leather sleeves . Waxed Twine .
Part No: 561012-1
|
|
|
|
|
Home -> Anchor & Docking -> Anchor Line & Dock Line -> Chafe Gear and Snubbers->Leather Chafe Guards
The traditional chafe protection that many still prefer. If sleeve is to be placed over tail of eye splice, order one size larger than line diameter. Includes: 2 pre-punched 10"L leather sleeves . Waxed Twine .
Part No: 561019-1
|
|
|
