Series 150 Clear PVC Tubing, 1/2"ID, 45psi Burst Pressure from SHIELDS RUBBER
Single layer, nontoxic, FDA-approved clear vinyl tubing. Ideal for drain lines, iceboxes, refrigerators, livewells, bilge pump discharge, freshwater lines, water and holding tank vents. Sold per foot: 50’ maximum continuous length for 1/4" and 3/8" hose; 100' maximum continuous length for 1/2" hose and larger. Application: Non-pressurized water system supply; sink, shower, and icebox drains. Material: FDA formula vinyl. Reinforcement: None. Temperature Range: N/A.

Drain Fitting, 1-1/4" Straight, 3/4" Hose, Plastic. from FORESPAR
1-1/4" Straight, 3/4" Hose, Plastic.

Tee Type Sanitation Hose Fitting, Slip Fitting Thread from SHIELDS RUBBER
Fiberglass-reinforced nylon fittings designed to fit Shields Series 101, 148 and 144 hoses without heating or special tools. Use in sanitation systems, deck drain systems and water tank fill.

Series 250 Exhaust Hose, 7/8"ID, 1-3/16"OD, 565psi Burst Pressure from SHIELDS RUBBER
For use in all marine water and wet-exhaust applications. Also for marine wet-exhaust where connection requires great length (greater than 4 x ID) or significant bend. Meets or exceeds standards for certified wet-exhaust hose. Sold by the foot with a maximum continuous length of 10' except where preceded by an asterisk, which indicates a maximum continuous length of 50'. Construction: Black synthetic rubber with wire helix and HD synthetic cord . Temperature Range: –20° to 200° F .

Series 250 Exhaust Hose, 2-3/8"ID, 2-3/4"OD, 230psi Burst Pressure from SHIELDS RUBBER
For use in all marine water and wet-exhaust applications. Also for marine wet-exhaust where connection requires great length (greater than 4 x ID) or significant bend. Meets or exceeds standards for certified wet-exhaust hose. Sold by the foot with a maximum continuous length of 10' except where preceded by an asterisk, which indicates a maximum continuous length of 50'. Construction: Black synthetic rubber with wire helix and HD synthetic cord . Temperature Range: –20° to 200° F .

Series 315 Outboard Fuel Hose - 3/8"ID from SHIELDS RUBBER
Premium-quality fuel hose designed for outboard feed and vent lines. Remains flexible at low temperatures and resists UV sunlight. Silverado 2000 complies with SAE J1527 Type B2 specifications. Should not be used in applications requiring the use of Type B1 fuel feed line.

2" ID, 90° Marine Rubber Exhaust Elbow from SHIELDS RUBBER
Exhaust hose elbows let your wet-exhaust line make tight turns without kinking. They provide excellent tolerance to engine heat, vibration and back pressure. Install over rigid tubing or pipe using the four included stainless T-bolt clamps (two at each end). Not intended for hose-to-hose connections. Lubricate with water or detergent. 250°F max.

5" ID, 45° Marine Rubber Exhaust Elbow from SHIELDS RUBBER
Exhaust hose elbows let your wet-exhaust line make tight turns without kinking. They provide excellent tolerance to engine heat, vibration and back pressure. Install over rigid tubing or pipe using the four included stainless T-bolt clamps (two at each end). Not intended for hose-to-hose connections. Lubricate with water or detergent. 250°F max.

PE-1 Lexan Mast Pad Eye from FORESPAR
For use on our small poles. 1-3/4"H x 1-1/4" x 5/8"dia. ring. Same ring as supplied with 4-8 and 6-12 poles.

Barbed Hose Reducer, 1" to 1-1/8" from MARINE EAST
.

12V Macerator Pump, 14A Draw from SHURFLO
Designed specifically for the marine environment with run dry premium impeller technology. 5" male thread to screw directly onto a tank flange. Type: Macerating flexible impeller gpm: 13 Macerates: Yes Self-Prime: 5' Material: Nylon body, nitrile impeller, stainless wear plate Port Sizes: Inlet: 1-1/2" barb and 1-1/2" NPT male; Outlet: 1" hose barb Dimensions: 3-3/8"H x 4-5/8"W x 11"L Innovative blade design ensures problem-free pumping Inlet port has both a 1.

Gas Deck Fill Replacement Cap, Locking from PERKO
Includes grounding lug with screw and integral retainer for cap For 1 1/2" hose Impervious to gasoline.

Waste Caddy from TODD ENTERPRISES
Todd Waste Caddy A portable 29-gal. capacity waste removal system. Moves easily on pneumatic tires with plastic bearings. Features a vented cap and 10-foot, 1-1/2"dia. hose and gravity-assisted pump that forces out fluid by gravity for a more rapid transfer. Spring-loaded nozzle eliminates leaks . Bronze ball valve is located at the bottom of the tank . Constructed of cross-linked polyethylene for strength and durability .

CP Zinc Elbow Catch from PERKO
Chrome-plated zinc with stainless steel spring. . Measures: 1 1/8" x 9/16" . Requires #6 RH screws (Not included).

Transom Drain Tube & Plug from MOELLER
This nylon drain tube won't rot, bend or mildew, fits flush to your transom, and allows water to drain when your vessel is trailered. A rubber O-ring makes a watertight seal. Can be loosened with a flat-head screwdriver. Fits 1 1/8'' openings. Mounted with rivets or #8 fasteners.