12V Reversible Flo-Master Vane Pump from GROCO
Rigid-vane pumps for pumping water, oil or diesel. Positive-displacement pump is self-priming to 2’. Long-lasting, continuous-duty, ignition-protected motor has ball bearings and a #316 stainless-steel shaft Application: General light to intermittent duty utility pumping . Gallons Per Minute: 6. 5 (oil) . Material: Bronze pumphead, stainless shaft . Port Sizes: Male garden hose or 1/2" female NPT inlet & outlet . Dimensions: 3 3/8"H x 4 3/8"W x 7 1/2"L .

Three Position Ignition Switch, OFF-Ignition-Start Functions from COLE HERSEE
Two position is for engines with a separate starter pushbutton. Three position: Off/Ignition/Start. Four position: Accessory/ Off/Ignition/Start or Off/Run/Push to Choke/Battery-Start (magneto switch). Brass construction, 2 keys supplied. 13/16" dia. mounting hole.

Bulk Pak Nylon Washers - 1/4", Pack of 100 from FASCO FASTENERS
These washers are white nylon for cushioning.

Furler Kit for Boat Length to 16', 500lb. SWL, 1/8" Max. Wire dia., 1/4" Pin dia., 2-1/2" Pin-to-Pin, 5/32" Furling Line dia. from HARKEN
Furl or set your jib from your cockpit Harken small boat furlers allow the sail to be set and furled from the cockpit, a critical convenience in many racing dinghies and trailerable sailboats. Constructed of Hardkote anodized Teflon-impregnated aluminum, they feature multiple stacked races of Delrin or Torlon ball bearings for smooth rotation under load. The jib’s luff wire must be properly seized to the sail, since it carries most of the headstay load. 434 furler for dinghies under 16ft. (4.

Stainless-Steel “S” Hook, 3/16" Wire Dia., 5/8" Inside Width from SEAFIT
Stainless Steel "S" Hooks. Polished Stainless Steel Made in the U. S. A.

500 RC Windlass, 600lb. Max. Pull, Boat Length 35', 1/4"HT Chain, 1/2" Rope Rode Size, 62'–Chain; 45'–Rope Speed Up/Min., 60' Speed Down/Min., 60A–75A @12V Draw from MAXWELL
These low-profile windlasses feature a patented tension system that maintains resistance required to feed chain/rope rode into the locker instead of jamming it in the windlass. Designed for easy installation, the motor can be oriented in any of 12 positions below decks. Two pieces bolt together quickly. Gasketed, watertight base. For decks to 2 3/4" thick. Capstan models and extra-long shafts for thick decks are available by Special Order. Style: Vertical . Rode Type: Rope/chain .

Bow Roller, Fits Sand (Danforth Style), Anchors up to 20 lb., Special Narrow Width (US Only) from LEWMAR
Anchor rollers make dropping and weighing anchor easier on you and your boat. They help reduce chafe, prevent scratches and dings to your boat’s finish and provide a secure place to store your anchor when used in conjunction with an optional chain stopper or tensioner. We stock rollers to fit the most common combinations of anchor, mounting style and boat. Installation note: overhanging anchor rollers should be supported along at least 2/3 of their length. Easily installed using common tools.

29mm Carbo Clew Block Assembly from HARKEN
From the folks who invented ball bearing blocks, this line of blocks boasts an excellent strength-to-weight ratio. 29mm doubles and triples feature a U-lock to hold the swivel in the front or side position, or allow it to spin freely. Use the 40mm blocks for jib and mainsheet systems on high-performance dinghies, and for high-load control lines on small keelboats. The 57mm blocks have an enormous working range that makes them ideal for main and jib sheets, spinnaker halyards and control lines.

Ratchet Orbit Block, Cheek, Counter-Clockwise, 550lb. SWL, 2.7oz. from RONSTAN
Practical Sailor's Ratchet Block Click-Off rated Ronstan's Orbit block "Overall, the most impressive with its grip, versatility, and lightweight design. It can be set at a 0 or 90 degree orientation, provides stress-free articulation without allowing the block to over-rotate, and is locked in place with a security clip that doesn’t require tools to fit. The Dyneema link is also more compatible with carbon, Dyneema and webbing connection points than steel loop tops or shackles.

Teak Plugs - 3/8" from SEAFIT
Use these teak plugs to cover screw heads or fill small holes for a beautiful smooth finish to your installation. Sizes: 1/4" 5/8" 5/16" 3/8" 1/2" 1".

Lateral Starboard Clamcleat, 1/4"–3/8" Rope Dia., 3/16"H x 2"W x 2-7/8"L, 1/4" Fasteners from CLAMCLEAT
.

1-7/8" Polished Brass Flush Ring Pull from ABI
Highly polished brass . Convenient flush-fitting ring pull for cabinets, small doors, and hatches. . 1-7/8"L x 1-1/2"w . Requires four #5 fasteners .

Deck Fill, Gas, w/Key, 1-1/2" from WHITECAP INDUSTRIES
Stainless-steel deck fills with durable cast heads—not the thin stamped heads found on many imports. Gas, Diesel and Water fills have 1 1/2" openings. Waste fill has 2" opening. All connect to 1 1/2" hose, and include a stainless key. Material: Stainless . Attachment Method: 1 1/2" hose . Flange Diameter: 3" or 3 1/2" (waste) . Fasteners: Three #10 FHMS . Cutout Diameter: 1 5/8" .

Stainless Strap Hinge, 2 5/8 inch from WEST MARINE
Type 304 electro-polished. Gauge: 0. 060 stainless steel. Drilled and countersunk for #8 fasteners (not included). Sold in pairs. ShWt .

5" Stainless-Steel Chock, Requires Two #10 FHMS Fasteners from PERKO
Fasteners not included.