Flex Trim - Black 1/2" opening from TACO PRODUCTS
For a beautiful finished look on unfinished edges. Just push it on and it's on to stay. Grips on difficult materials, compound curves, etc. Individual corrosion resistant aluminum clips for a permanent grip. Black or White . Sold in 25' lengths. . Available in four sizes:. 5/32" opening x 35/64"H. 1/4" opening x 1/2"H. 3/8" opening x 5/8"H.

50' Braided Polyester Cord from NEW ENGLAND ROPES
A low-stretch cord that’s great for flag halyards, foredeck netting, or light-air spinnaker sheets. Length: 50'. Diameter: 1/8". Best use: Utility cord, flag halyards . Construction: Braided polyester . Breaking strength: 530lb. . Stretch: 3% at 15% of breaking strength .

Series 150 Clear PVC Tubing, 1/2"ID, 45psi Burst Pressure from SHIELDS RUBBER
Single layer, nontoxic, FDA-approved clear vinyl tubing. Ideal for drain lines, iceboxes, refrigerators, livewells, bilge pump discharge, freshwater lines, water and holding tank vents. Sold per foot: 50’ maximum continuous length for 1/4" and 3/8" hose; 100' maximum continuous length for 1/2" hose and larger. Application: Non-pressurized water system supply; sink, shower, and icebox drains. Material: FDA formula vinyl. Reinforcement: None. Temperature Range: N/A.

Roller Shaft Cap Nuts Only - 1/2", Pack of 8 from C E SMITH
Roller Size Length Shaft Diameter Shafts and Nuts 4" 5 1/4" 1/2" 4" 5 1/4" 5/8" 5" 6 1/4" 1/2" 5" 6 1/4" 5/8" 8" 9 1/4" 5/8" 10" 11 1/8" 5/8" 11" 12 3/4" 1/2" 12" 13 1/2" 5/8" Shaft Only 18" 19" 5/8" Cap Nuts Only Packs of 8.

3/8" Bow/Stern Eye - 1.03" ID Between Studs x 4.63" Thread Length from SUNCOR
Bow / Stern Eye 304 Stainless Steel - Formed . Each U-Bolt set includes four nuts (two standard and two beveled) . Includes one bow plate, and one stern plate. . Threads are "UNC". . Stock size: 3/8" . ID between studs: 1. 03" . Thread length: 2. 50" .

Gunnel Guard - 1/2" Round, 1-1/2" Diameter, 20' Length from TAYLOR
These polyester-covered guards will protect your boat from dings and scratches and they won’t rot in the sun or saltwater like cotton guards. Great for use on dinghies and swim platforms, too. Fabric tabs attach easily with screws or nails. Half Round is for flat surfaces; 3/4 Round is for 90° edges. Sold in 10' or 20' lengths or by the foot up to 50'. Material: Polyester fabric/closed-cell foam . Attachment Method: Screws or nails . Shock Absorption Mechanism: Foam padding .

Clamp-On Rod Holder - 1 1/4"ID Horizontal, Gold from WEST MARINE
1 1/4IN HORIZONTAL MOUNT.

Tubing-Alu 7/8X20' from WEST MARINE
Bright 304 polished stainless steel or bright anodized aluminum. Used for a multitude of applications including grab rails, bow rails, and canvas top frames. Match materials between components to minimize corrosion. Stainless has . 049" wall thickness . Aluminum has . 058" wall thickness . Use 7/8" tubing for smaller powerboats . Use 1" tubing for sailboats and larger powerboats . Available in 6', 12' and 20' lengths .

Single Channel-Mate Glass Channel, 7/16"W from BECKSON MARINE
This window track is ideal for window glass or for installing sliding cabinet doors. Each channel groove is slightly (. 005") narrower than 1/4" window glass so there is positive pressure against the glass at all times. It seals out leaks and prevents glass from rattling. Made of B-FLEX marine plastic, it will not crack or discolor. The elevated slide at the bottom of the channel makes windows or doors easy to open and close. Sold in 8' lengths.

Acetal Thru-Transom Scupper from WEST MARINE
One-way rubber flapper valve and thru-hull fitting. For 1-1/2"ID hose. Overall length: 6-1/4". Installation hole size: 2". Max.

WL/1 Fairlead Model from SPINLOCK
New low-profile design easily mounts to 1" stanchion using internal clamping system. WL/2 sheave model utilizes unique tracker ball angle adjustment. WL/1 Fairlead model includes stainless-steel bullseye for strength.

1-7/8" Brass Standard Hasp from ABI
Highly polished brass . Fixed eye (does not swivel). 1"w x 1-7/8"L. Padlock hole diameter 5/16" .

G. O'Day 222/Santana 525,Length 47", Height at tip 2 1/4", Width at butt 1 1/2", Width at tip 2" from WEST MARINE
Replace that old ugly tiller with a new hand-made laminated ash and mahogany wood tiller, made to fit your rudder hardware, and pre-finished with multiple coats of premium marine spar varnish. Choose the right length and profile, and the butt-end measurements to fit your rudderhead hardware. Can’t find a good fit? Idasailor Marine can custom-build a tiller to your measurements . Custom tillers are shipped direct within 10 days . Click HERE to open the PDF custom order form.

1/4" NPT X 3/8" Brass hose barb from MOELLER
1/4 NPT X 3/8" Brass Hose barbs with male threads.

Telescopic Tiller Extension 29" - 48" from RONSTAN
Ronstan tiller extensions feature fluted anodized aluminum tubing for durability and rigidity and a tapered, non-slip Hyperlon grip with ball end. The Urethane universal joint can be removed without tools. Adjustable-length versions feature a fast-action adjustable shaft for additional versatility. 4732913 Aluminum Fixed 24” RF3128 5/8"Tubing Dia. , 1"Grip Dia. , 24"L, 5. 3Lbs. 1133131 Lightweight Aluminum 33” RF3129 5/8"Tubing Dia. , 1"Grip Dia.