Stainless-Steel “S” Hook, 3/16" Wire Dia., 5/8" Inside Width from SEAFIT
Stainless Steel "S" Hooks. Polished Stainless Steel Made in the U. S. A.

Furler Kit for Boat Length to 16', 500lb. SWL, 1/8" Max. Wire dia., 1/4" Pin dia., 2-1/2" Pin-to-Pin, 5/32" Furling Line dia. from HARKEN
Furl or set your jib from your cockpit Harken small boat furlers allow the sail to be set and furled from the cockpit, a critical convenience in many racing dinghies and trailerable sailboats. Constructed of Hardkote anodized Teflon-impregnated aluminum, they feature multiple stacked races of Delrin or Torlon ball bearings for smooth rotation under load. The jib’s luff wire must be properly seized to the sail, since it carries most of the headstay load. 434 furler for dinghies under 16ft. (4.

29mm Carbo Clew Block Assembly from HARKEN
From the folks who invented ball bearing blocks, this line of blocks boasts an excellent strength-to-weight ratio. 29mm doubles and triples feature a U-lock to hold the swivel in the front or side position, or allow it to spin freely. Use the 40mm blocks for jib and mainsheet systems on high-performance dinghies, and for high-load control lines on small keelboats. The 57mm blocks have an enormous working range that makes them ideal for main and jib sheets, spinnaker halyards and control lines.

500 RC Windlass, 600lb. Max. Pull, Boat Length 35', 1/4"HT Chain, 1/2" Rope Rode Size, 62'–Chain; 45'–Rope Speed Up/Min., 60' Speed Down/Min., 60A–75A @12V Draw from MAXWELL
These low-profile windlasses feature a patented tension system that maintains resistance required to feed chain/rope rode into the locker instead of jamming it in the windlass. Designed for easy installation, the motor can be oriented in any of 12 positions below decks. Two pieces bolt together quickly. Gasketed, watertight base. For decks to 2 3/4" thick. Capstan models and extra-long shafts for thick decks are available by Special Order. Style: Vertical . Rode Type: Rope/chain .

Hatch Riser Arm for 20" x 20" Hatch from TAYLOR
Replacement arms for Taylor hatches from 1987 to the present. Universal arms can be left or right.

10mm Ball Stud pair from TAYLOR
Taylor 10mm Ball Stud pair.

Rechargeable Signal Air Horn from TAYLOR
Environmentally safe air horn uses air as a propellant, instead of the traditional gas-filled designs. It's economical too. no more expensive refills to buy. Recharges in seconds with a gas station air pump, air compressor, or any other mechanical compressed air source including hand pumps. Works in all weather extremes and can safely be used or stored near sources of heat. Provides approximately 20 blasts per charge. This loud horn puts out a powerful 120db. Meets all USCG regulations.

84”L Fiberglass Bow from TAYLOR
Bows moounted in bow sockets are the sure and easy way to keep a boat cover taut and free from water-collecting pockets. Sockets can be mounted on any rail system or anywhere on deck wall. Rubber gasket provides snug fit for fiberglass bows. Super strong and flexible, will not take a “set”. Cut to desired length. Incude rubber end covers to grab socket.

Replacement Gas Strut, 12" Compressed x 20" Extended Length, 40lb. Rating from TAYLOR
Reliable gas struts incorporate a strong annealed steel rod with a special coating for added corrosion resistance. Recommended by the manufacturer for use as dock box lid supports or hatch supports. Where use as a hatch cover support is desired, we recommend you base your selection upon the recommendation of the hatch manufacturer.

Adjustable Lock from TAYLOR
Three-part system provides easy snap-on/snap-off fender attachment and adjustment. A stainless base mounts to your boat, into which a peg snaps to hold the fender strap (sold separately). Fixed peg requires tying a knot to secure the fender at the desired height. Adjustable peg - adjust fender height by simply pulling on the strap. Max.

T-Top Boat Cover, Center-Line Length 20'5" to 21'4", Blue from TAYLOR
The main features of these covers are: Bow and stern sections are separated into two halves. The sections are joined through the use of a 7mm single pull molded nylon zipper on both the port and starboard sides. Cover design incorporates a "console tube" section with two adjustable straps which lift and secure the cover halves up and over the console body and up under the T-top. The top edge of console tube incorporates an adjustable draw rope in both front and rear sections.

Welcome Aboard Mat, Navy, 18" X 30" from TAYLOR
High-quality, marine-grade mats will add spice to any deck or door. Made from plush carpet that is waterproof, stain- and fade-resistant. Mats are mold- and mildew-resistant and feature a nonskid rubber backing.

Sully Stick Winter Mooring Buoy from TAYLOR
Extend the life of your mooring with our ice-proof stickUse this long tapered buoy in place of a standard round buoy during winter months to help prevent ice entrapment and extend the life of the mooring by protecting it from the damaging effects of freezing temperatures. Molded in eyelet at the top allows for easy retrieval and the base eyelet is reinforced with galvanized metal brushing to attach a rope and connect to the anchor chain. 80"L x 6" Dia.

Medium Edging, White, 25' Coil, 3-1/2"H x 1-1/2"W from TAYLOR
Prevent scuffing when you dock Vinyl dock guard is specially formulated for softness and durability to protect your boat or dinghy. Each piece installs easily with screws or nails to the edge of docks, piers and floats. Material: Extruded PVC . Attachment Method: Stainless steel dock nails . Shock Absorption Mechanism: Flexible PVC .

Single Deck Chair Cover, 24"H x 24"W x 22"D from TAYLOR
Protect your seats from the elements!Heavy-duty waterproof poly/vinyl blend keeps your seats from cracking and fading. Poly/vinyl blend is softer and more pliable than traditional vinyl.