Rule-A-Matic Plus Float Switch from RULE INDUSTRIES
Is the float switch working? It's easy to check! Features a Rule-A-Matic float switch and an impact-resistant cover to protect against debris and jamming. Wiring is "blocked" by a rubber grommet to provide strain relief. Includes a convenient feature for manual tests. Activation Method: Float with mechanical contacts. Dimensions: 2-3/4"H x 2-1/2"W x 4-7/8"L. Capacity: 20A @ 12/24/32V DC.

SeaStar Helm Seal Kit from TELEFLEX
Replacement shaft seal kit HS5176 fits various post-1990 SeaStar 1. 4, 1. 7 (I), 2. 0, 2. 4 (II), SeaStar Pro and SeaStar helms.

5/8" Clevis Pin dia., 1-3/16" inside dia., 4-pack from WEST MARINE
Stainless-Steel Cotter Rings.

Aft-Deck Shower System from ATTWOOD
This compact hot/cold shower stores neatly in its own compartment on the stern or in the head. Includes a handheld shower spray head with shutoff, 6' hose, hot/cold water controls and a cover. Easily hooked into your freshwater system. Compartment is drilled for six #8 fasteners. Material: High-impact plastic . Dimensions: 9-1/2"H x 5"W x 2-1/4"D . Hose Size: 6'L . Port Sizes: 1/2" NPT .

VC-Offshore - Baltoplate Gray, Gallon from INTERLUX
Used by performance boatsVC Offshore combines superior antifouling performance with a super smooth low friction surface for the performance conscious boater. This high-strength, vinyl antifouling paint, fortified with Teflon® yields a hard, very smooth finish for maximum durability, reduced friction and increased performance. High copper loading fights fouling on performance boats in saltwater. Can be used in fresh, salt and brackish waters. Should not be applied over non-vinyl bottom paints.

24 Volt Shower Drain from ITT JABSCO
Shower pump turns itself on and off automaticallyA full-capacity shower drain system with automatic activation. Includes a clear, screw-down cover for easy inspection, removable strainer for easy cleaning, and an internal check valve to prevent back siphoning. 800gph capacity. Consists of a bilge pump, Rule-A-Matic float switch and an enclosing sump.

FLAG Resin, 1/2 Gallon from MAS EPOXY
We highly recommend this resin for general purpose gluing applications where wet-out of fiberglass is not a consideration, and for all your filleting and fairing needs. FLAG Resin is a "medium" body resin specifically designed to perform as an adhesive and structural laminating foundation. FLAG is more reactive than our Low Viscosity Resin when mixed with Medium Hardener. FLAG Resin may be used with all MAS Hardeners, however, for filled applications we recommend our Medium Hardener.

Hatch Riser Arm for 20" x 20" Hatch from TAYLOR
Replacement arms for Taylor hatches from 1987 to the present. Universal arms can be left or right.

10mm Ball Stud pair from TAYLOR
Taylor 10mm Ball Stud pair.

Gunnel Guard - 1/2" Round, 1-1/2" Diameter, 20' Length from TAYLOR
These polyester-covered guards will protect your boat from dings and scratches and they won’t rot in the sun or saltwater like cotton guards. Great for use on dinghies and swim platforms, too. Fabric tabs attach easily with screws or nails. Half Round is for flat surfaces; 3/4 Round is for 90° edges. Sold in 10' or 20' lengths or by the foot up to 50'. Material: Polyester fabric/closed-cell foam . Attachment Method: Screws or nails . Shock Absorption Mechanism: Foam padding .

Flag Epoxy Repair Kit from MAS EPOXY
For small repairs and bonding; Perfect where only a small amount is needed. Small enough to keep on board, but enough epoxy to make most quick repairs! Kit includes: 16oz. Flag Epoxy Resin. 8oz. medium hardener. 10 mixing sticks. 4pr. gloves.

Medium Edging, White, 25' Coil, 3-1/2"H x 1-1/2"W from TAYLOR
Prevent scuffing when you dock Vinyl dock guard is specially formulated for softness and durability to protect your boat or dinghy. Each piece installs easily with screws or nails to the edge of docks, piers and floats. Material: Extruded PVC . Attachment Method: Stainless steel dock nails . Shock Absorption Mechanism: Flexible PVC .

1/4" NPT X 3/8" Brass hose barb from MOELLER
1/4 NPT X 3/8" Brass Hose barbs with male threads.

Drain Fitting, 1-1/4" Straight, 3/4" Hose, Plastic. from FORESPAR
1-1/4" Straight, 3/4" Hose, Plastic.

Braided Polyester Cord, by the Foot from NEW ENGLAND ROPES
A low-stretch cord that’s great for flag halyards, foredeck netting, or light-air spinnaker sheets. Sold by the foot. Diameter: 1/8". Best use: Utility cord, flag halyards . Construction: Braided polyester . Breaking strength: 530lb. . Stretch: 3% at 15% of breaking strength .