Top Sellers
Trim Tab Zinc Anode from CANADA METALS
Attaches to standard Bennett trim tabs where actuator bolts to plate.
|
Zinc Grouper Anode from CANADA METALS
Supplements your boat's existing anodes An excellent anodic device to supplement a vessel’s existing anode system, especially to counteract stray current from defective shore power. Clip to bolt on outdrive. Clip to grounding strap if possible or wire items together with copper wire and clip to wire. Do not connect to negative battery terminals. Dimensions: 8 1/4"L x 3 1/4"W x 1 3/8"D.
|
Aluminum Anode Kit Bravo II & III from CANADA METALS
Offered in aluminum, for use in salt or brackish water, or magnesium, for freshwater only.
|
Boeshield T-9 Spray Lube from BOESHIELD
Penetrates, lubricates and protects This combination of solvents, lubricants and waxes was designed to penetrate, lubricate and protect surfaces, and to displace moisture. It dries to a thin, waxy, corrosion-preventing film that clings to metal for months. It will loosen rusty and corroded parts and is safe on paints, plastics and vinyls. Aerosol spray gets into cracks and crevices. 12oz.
|
10 Micron Diesel Fuel Filter/Water Separator with Metal Bowl from RACOR-PARKER FILTRAT
Racor’s Aquabloc filter media removes virtually 100% of water and solid contaminants. Filters have die-cast aluminum heads and come in different sizes for diesel engines and any rate of fuel flow. To be used on the suction side of the pump. See-thru bowls allow visual inspection for water; metal bowls are recommended for use in areas of high heat and are required by the US Coast Guard on inboard engines and gensets. Inlets/Outlets: 1/4" NPT female . Bowl Material: See-thru polymer .
|
Power Bubbles 12V DC Aerator from MARINE METALS
This system runs on low current as it's dual bellows aerate up to 2L per minute of air. It saturates circulating water with oxygen. Double discharge allows aeration of one or two livewells. Increases flow capacity. Includes 10' of air tubing. Two large airstones allow the pump to be mounted in any protected area. Suitable for fresh or saltwater. Two anti-siphon valves protect pump against water intrusion. Quietly operates with solid-state circuits. Draw: 1/4A at 12V DC.
|
Crack Cure Sealant, 2 OZ. from CAPTAIN TOLLEY S
Excellent for sealing hairline cracks in gelcoatThis penetrating copolymer sealant is formulated to be so thin that by using capillary action it can find its way inside fine cracks and set to a clear, flexible seal. Use on wood, rubber, glass, metals, fiberglass, Lexan, ceramic and concrete. Formulation: One-part water-based acrylic polymer sealant. Recommended Usage: Fixing leaks in wood, rubber, glass, metal, ceramics, and other materials . until saturated. Color: Milky . Quantity: 2oz.
|
|
|
|
|
57mm Black Magic AirBlock, High-Load Strap Head with Becket, 2,500lb. SWL, 3.6oz. from HARKEN
Strong, lightweight aluminum blocks for offshore boats Used for sheets, halyards, running backstays and control lines on offshore boats, these strong, lightweight blocks are made of sculpted aluminum with Torlon rollers and carbon black balls for strength and UV protection. Cheek Material/Finish: 6160-T6 Hardkote anodized aluminum . Sheave Size: 57mm (2-1/4") . Construction: Three fasteners for quick disassembly. Plastic isolators separate dissimilar metals. Three-way head system.
|
Rejuvenate 2-Cycle Engine Oil, Pint from MERCURY MARINE
Rejuvenate is unlike anything on the market today. It rolls back the clock on engines by quickly removing performance robbing carbon deposits while stabilizing fuel. Powerful detergents remove carbon deposits on piston skirt, crowns and under crowns, power valves, cylinder intake, exhaust and heads. For air-cooled or water-cooled 2-cycle engines with premixed fuel or oil injection systems.
|
Rejuvenate 2-Cycle Engine Oil, Gallon from MERCURY MARINE
Rejuvenate is unlike anything on the market today. It rolls back the clock on engines by quickly removing performance robbing carbon deposits while stabilizing fuel. Powerful detergents remove carbon deposits on piston skirt, crowns and under crowns, power valves, cylinder intake, exhaust and heads. For air-cooled or water-cooled 2-cycle engines with premixed fuel or oil injection systems.
|
Lube Tube Adapter for Yamaha, Nissan, Tohatsu, Honda (2-50hp) from WEST MARINE
Marine lower unit drain, flush and fill tool. Metal threaded fitting fits MerCruiser, OMC, Evinrude, Johnson, Honda (70-90hp), Volvo, Force and Gamefishier lower units. Quick, easy and clean way to change marine lower unit gear lube. For use with all 8- and 10-oz.
|
TC-W3 100% Synthetic 2-Cycle Outboard Oil from PENNZOIL
This high-flash, ashless 2-cycle engine oil with biodegradable formulation meets or exceeds 2-cycle outboard manufacturer's warranty requirements. It provides excellent lubricity and wear and rust protection in both pre-mix and injection systems. Exceeds NMMA requirements.
|
Rounded Oval, 8-1/2"W x 11-1/4"L x 5-1/4"D, 1" Flange, 1-1/2" Drain from AMBASSADOR MARINE
Made from 304 stainless steel and mirror-polished to a deep luster, these sinks incorporate SoundKOTE Noise Reduction Technology to reduce the unpleasant clanging associated with many metal sinks. Flanges permit over- or under-the-counter mounting. Low-Profile 90° drains fit standard 1"ID hose and are slanted to maximize drainage.
|
|
2"L from CANADA METALS, CM43994M from CANADA METALS
|
This site contains about 37,785 documents.
|
|
View by:
Title
|
Category
|
Manufacturer
|
Part No
|
Price
|
|
Page:
1
100
200
300
400
500
600
700
850
860
870
880
890
900
910
920
930
943
944
945
946
947
948
949
950
951
952
953
954
955
956
957
958
959
960
961
962
963
964
965
966
967
968
969
970
971
972
980
990
1,000
1,010
1,020
1,030
1,040
1,050
1,100
1,200
1,260
|
|
|
Home -> Paint & Maintenance -> Zinc Anodes->Outdrive Anodes, MerCruiser
Sold in pairs or, where indicated, in kits which include hardware.
Part No: CM821629KITM
|
|
|
|
Home -> Paint & Maintenance -> Zinc Anodes->Outdrive Anodes, MerCruiser
Sold in pairs or, where indicated, in kits which include hardware.
Part No: CM762144KITM
|
|
|
|
Home -> Paint & Maintenance -> Zinc Anodes->Outdrive Anodes, MerCruiser
Sold in pairs or, where indicated, in kits which include hardware.
Part No: CM821630KITM
|
|
|
|
Home -> Paint & Maintenance -> Zinc Anodes->Outdrive Anodes, MerCruiser
Sold in pairs or, where indicated, in kits which include hardware.
Part No: CM865182M
|
|
|
|
Home -> Paint & Maintenance -> Zinc Anodes->Outdrive Anodes, MerCruiser
Sold in pairs or, where indicated, in kits which include hardware.
Part No: CM762144M
|
|
|
|
Home -> Paint & Maintenance -> Zinc Anodes->Outdrive Anodes, MerCruiser
Sold in pairs or, where indicated, in kits which include hardware.
Part No: CM762145Z
|
|
|
|
Home -> Paint & Maintenance -> Zinc Anodes->Outdrive Anodes, MerCruiser
Sold in pairs or, where indicated, in kits which include hardware.
Part No: CM821629CZ
|
|
|
|
Home -> Paint & Maintenance -> Zinc Anodes->Outdrive Anodes, MerCruiser
Sold in pairs or, where indicated, in kits which include hardware.
Part No: CM806190Z
|
|
|
|
Home -> Paint & Maintenance -> Zinc Anodes->Outdrive Anodes, MerCruiser
Sold in pairs or, where indicated, in kits which include hardware.
Part No: CM43994M
|
|
|
|
Home -> Paint & Maintenance -> Zinc Anodes->Pencil Zincs Anodes
Pencil Zincs Anodes; all zinc anodes conform to Mil-A-18001, all aluminum anodes conform to Mil-A-24779.
Part No: E-2-SPARE
|
|
|
|
Home -> Paint & Maintenance -> Zinc Anodes->Plate Anodes
ZHC - Drivers Dream; all zinc anodes conform to Mil-A-18001, all aluminum anodes conform to Mil-A-24779.
Part No: ZHC-4
|
|
|
|
Home -> Paint & Maintenance -> Zinc Anodes->Zinc Outboard Anode - OMC 393023
Zinc Outboard Anode - OMC #393023.
Part No: CM984513Z
|
|
|
|
Home -> Paint & Maintenance -> Zinc Anodes->Zinc Streamlined Collar Anodes
Canada Metal zincs are composed of an alloy that meets Mil-Spec MIL-A-18001 for sacrificial anodes. This alloy is mostly zinc, but with measurable concentrations of cadmium (~0. 1%) and aluminum (~0. 25%). The additional cadmium causes the anode to erode from the surface inward, which causes a ''sandblasted'' appearance to the surface.
Part No: CMX07
|
|
|
|
Home -> Paint & Maintenance -> Zinc Anodes->Zinc Streamlined Collar Anodes
Canada Metal zincs are composed of an alloy that meets Mil-Spec MIL-A-18001 for sacrificial anodes. This alloy is mostly zinc, but with measurable concentrations of cadmium (~0. 1%) and aluminum (~0. 25%). The additional cadmium causes the anode to erode from the surface inward, which causes a ''sandblasted'' appearance to the surface.
Part No: CMX05
|
|
|
|
Home -> Paint & Maintenance -> Zinc Anodes->ZPN - Solid Zinc Plates
ZPN - Solid Zinc Plates; all zinc anodes conform to Mil-A-18001, all aluminum anodes conform to Mil-A-24779. No Core.
Part No: ZPN-1
|
|
|
|
Home -> Plumbing -> Bilge Pumps
The High Water Bilge Alarm consists of a non-mercury float switch and an in-dash gauge that features both a visual and an audible 85 db alarm. This unit allows an unmanned compartment to be constantly monitored. For additional compartments, add additional Rule Float Switches. Complies with CFR 182. 530, which requires a visual and audible alarm in each unmanned space on commercial vessels at least 26' (7. 9m) in length.
Part No: 33ALA
|
|
|
|
Home -> Plumbing -> Bilge Pumps
Essential items for installing a bilge pump Convenient package includes four #8 x 3/4" stainless-steel panhead screws, one 1-3/4" x 3/4" stainless steel hose clamp, and three 16-14AWG heat shrink butt connectors.
Part No: 407001
|
|
|
|
Home -> Plumbing -> Bilge Pumps
Is the float switch working? It's easy to check! Features a Rule-A-Matic float switch and an impact-resistant cover to protect against debris and jamming. Wiring is "blocked" by a rubber grommet to provide strain relief. Includes a convenient feature for manual tests. Activation Method: Float with mechanical contacts. Dimensions: 2-3/4"H x 2-1/2"W x 4-7/8"L. Capacity: 20A @ 12/24/32V DC.
Part No: 40A
|
|
|
|
Home -> Plumbing -> Bilge Pumps
Push-fit ports swivel through 360° for flexibility in installation. A special quick-release clamp ring gives fast access for clearing blockages. Surface-mount style, with detachable handle. Includes one elbow.
Part No: 29270-0000
|
|
|
|
Home -> Plumbing -> Bilge Pumps
Gusher 30 Pump The Gusher 30 is a double-action pump with twin diaphragms so it will still function if one side becomes clogged. Constructed from epoxy-coated anodized aluminum with a brilliant white finish. Nitrile valves and diaphragms perform well under harsh conditions . Accepts low-resistance 2" hose adapters for maximum performance . 31 GPM @ 70 strokes/min. @ 0 head. . Body: Anodized aluminum .
Part No: BP3000
|
|
|
|
Home -> Plumbing -> Bilge Pumps
Dry out small boats fast with our six gallon per minute pumpKeep this hand bilge pump in your canoe or kayak for quick evacuation of water from a leak or capsize. Foam collar provides buoyancy in case it goes overboard and the 18" long pump has a T-handle for easy pumping. Pumps up to 6 gpm. Keep this hand bilge pump with you while you paddle. Foam collar makes it float in case it goes overboard.
Part No: 88005
|
|
|
|
Home -> Plumbing -> Bilge Pumps
Die-cast, epoxy-coated, anodized alloy, synthetic neoprene rubber diaphragm and stainless steel. Removable stainless handle with lanyard. To complete the installation, select either the Aluminum or Plastic Thru-Deck Kit, which seal the installation against water intrusion and and give it a finished look. Nitrile Diaphragm Kit, AK3714, available through special order. Material: Anodized aluminum . Dimensions: 8"H x 4-1/8"W x 5-3/4"L . Port Sizes: 1-1/2" .
Part No: BP3740
|
|
|
|
Home -> Plumbing -> Bilge Pumps
The 1800gph pumping capacity and extra-long 24' power cord make this pump great for boats with shore power or protecting basements from flooding during wet weather. Motor and durable housing will last for years on the boat or in the home. 5/8" garden hose adapter. gph: 1800. Draw: 1. 1A@110V AC. Built-In Switch: Yes. Material: Plastic. Dimensions: 7-3/4" x 4-3/4". Port Size: 1-1/8".
Part No: A53S-24
|
|
|
|
Home -> Plumbing -> Bilge Pumps
In the event of a problem, replacing your cartridge bilge pump motor is easy— provided you keep one of these on hand. Just pop out the old cartridge and pop in the new. Fit Johnson, West Marine Bilge Pro and Mayfair cartridge-style bilge and livewell pumps.
|
|
|
|
Home -> Plumbing -> Bilge Pumps
In the event of a problem, replacing your cartridge bilge pump motor is easy— provided you keep one of these on hand. Just pop out the old cartridge and pop in the new. Fit Johnson, West Marine Bilge Pro and Mayfair cartridge-style bilge and livewell pumps.
|
|
|
|
Home -> Plumbing -> Bilge Pumps
Heavy duty construction for both commercial and pleasure boat use; known for trouble free operation and reliability. 1-1/2" (38mm) discharge outlet. Flow Rate: 3700 gph 14010 lph . Port Type: 1-1/2" (38mm) Hose barb . Voltage: 12 Vdc . Amp Draw: 15. 5 amp . Fuse Size: 25 amp . Height: 8-1/4 inches 209. 5 mm . Width: 4-7/8 inches 124 mm .
Part No: 55S
|
|
|
|
Home -> Plumbing -> Bilge Pumps
Engineered to commercial standards. The Rule 2000 is the best selling high capacity submersible bilge pump in the world. 1-1/8" (28. 6mm) discharge outlet. Voltage: 12 Volts. Flow Rate: 2000 gph 7571 lph . Port Type: 1-1/8" (28mm) Hose barb . Amp Draw: 8. 4 amp . Fuse Size: 15 amp . Height: 7-3/4 inches 196.
Part No: 53S
|
|
|
|
Home -> Plumbing -> Bilge Pumps -> Bilge Pump Parts
Adds mounting versatility to Rule 360, 500 and 1100gph pumps Allows you to mount a Rule 360, 500, or 1100 gph pump to a vertical stringer or transom.
Part No: 66
|
|
|
|
Home -> Plumbing -> Bilge Pumps -> Bilge Pump Parts
One-piece brass casting. Fits 5/8" hose .
Part No: 14555-0000
|
|
|
|
Home -> Plumbing -> Bilge Pumps -> Bilge Pump Parts->Bilge Pro Pump Accessories
Bilge Pro Pump Accessories Check valve- cartridge bilge. Dura Port Straight Kit. Dura Port 90 Degree Kit.
Part No: 92105
|
|
|