Step Pad, 10-3/4" x 5-1/4", Blue from LEWMAR
Maintain your footing under all conditions! Self-adhesive, diamond-patterned, nonskid pads are great for decks, steps, dinghy floors, personal watercraft, etc. They resist wear and tear, peeling, saltwater, fuels and chemicals. Pads have rounded edges and are precut to fit most common step sizes. Trim with scissors for a custom fit. Peel-and-stick installation. Sold in pairs.

Hatch Riser Arm for 20" x 20" Hatch from TAYLOR
Replacement arms for Taylor hatches from 1987 to the present. Universal arms can be left or right.

10mm Ball Stud pair from TAYLOR
Taylor 10mm Ball Stud pair.

Fishing Boat Cover - HS Blue 15'5"-16'4"/65" Beam from TAYLOR
Patterned to fit basic fishing boats with bench seats. (These covers are not patterned to fit over trolling motors. ) The bow and transom corners are reinforced to protect the cover from sharp aluminum edges. Poly Cotton Fabric: Trailerable 65% polyethelyne/35% cotton Breathable Mildew & Stain Resistant Water Repellant Heavy-gauge shock cord in hem 2-year limited warranty Color: Silver Gray. Hot Shot Fabric (HS): Trailerable 100% urethane-coated polyester 7.

T-Top Boat Cover, Center-Line Length 20'5" to 21'4", Blue from TAYLOR
The main features of these covers are: Bow and stern sections are separated into two halves. The sections are joined through the use of a 7mm single pull molded nylon zipper on both the port and starboard sides. Cover design incorporates a "console tube" section with two adjustable straps which lift and secure the cover halves up and over the console body and up under the T-top. The top edge of console tube incorporates an adjustable draw rope in both front and rear sections.

T-Top Boat Cover, Center-Line Length 19'5" to 20'4", Blue from TAYLOR
The main features of these covers are: Bow and stern sections are separated into two halves. The sections are joined through the use of a 7mm single pull molded nylon zipper on both the port and starboard sides. Cover design incorporates a "console tube" section with two adjustable straps which lift and secure the cover halves up and over the console body and up under the T-top. The top edge of console tube incorporates an adjustable draw rope in both front and rear sections.

Back-to-Back Lounge Chair Seat Cover, 22"H x 50"W x 22"D from TAYLOR
Breathable rip/stop polyester fabric plus air vents provide optimum protection and ventilation for your seats, especially in hot and humid climates. Polyurethane coating on the inside prevents color transfer or bleed-through . Comes with drawstring hem . Available for most popular seat styles .

84”L Fiberglass Bow from TAYLOR
Bows moounted in bow sockets are the sure and easy way to keep a boat cover taut and free from water-collecting pockets. Sockets can be mounted on any rail system or anywhere on deck wall. Rubber gasket provides snug fit for fiberglass bows. Super strong and flexible, will not take a “set”. Cut to desired length. Incude rubber end covers to grab socket.

Replacement Gas Strut, 12" Compressed x 20" Extended Length, 40lb. Rating from TAYLOR
Reliable gas struts incorporate a strong annealed steel rod with a special coating for added corrosion resistance. Recommended by the manufacturer for use as dock box lid supports or hatch supports. Where use as a hatch cover support is desired, we recommend you base your selection upon the recommendation of the hatch manufacturer.

Adjustable Lock from TAYLOR
Three-part system provides easy snap-on/snap-off fender attachment and adjustment. A stainless base mounts to your boat, into which a peg snaps to hold the fender strap (sold separately). Fixed peg requires tying a knot to secure the fender at the desired height. Adjustable peg - adjust fender height by simply pulling on the strap. Max.

Welcome Aboard Mat, Navy, 18" X 30" from TAYLOR
High-quality, marine-grade mats will add spice to any deck or door. Made from plush carpet that is waterproof, stain- and fade-resistant. Mats are mold- and mildew-resistant and feature a nonskid rubber backing.

Sully Stick Winter Mooring Buoy from TAYLOR
Extend the life of your mooring with our ice-proof stickUse this long tapered buoy in place of a standard round buoy during winter months to help prevent ice entrapment and extend the life of the mooring by protecting it from the damaging effects of freezing temperatures. Molded in eyelet at the top allows for easy retrieval and the base eyelet is reinforced with galvanized metal brushing to attach a rope and connect to the anchor chain. 80"L x 6" Dia.

Medium Edging, White, 25' Coil, 3-1/2"H x 1-1/2"W from TAYLOR
Prevent scuffing when you dock Vinyl dock guard is specially formulated for softness and durability to protect your boat or dinghy. Each piece installs easily with screws or nails to the edge of docks, piers and floats. Material: Extruded PVC . Attachment Method: Stainless steel dock nails . Shock Absorption Mechanism: Flexible PVC .

Single Deck Chair Cover, 24"H x 24"W x 22"D from TAYLOR
Protect your seats from the elements!Heavy-duty waterproof poly/vinyl blend keeps your seats from cracking and fading. Poly/vinyl blend is softer and more pliable than traditional vinyl.

Fender Pump from TAYLOR
Compact, high-pressure hand pump for filling fenders, rafts, footballs, etc.