Top Sellers
Premium 4-Cycle Heavy-Duty SAE 15W40 Engine Oil, Gallon from WEST MARINE
An excellent choice for all 4-cycle inboard diesel and gasoline engines operating in all conditions. Clean-burning formula meets or exceeds both industry and factory performance specifications. Powerful additives allow for dependable engine service.
|
PAR-Max 4 Water-System Pump, 12V from JABSCO
Flow rate: 16. 3 Litres/min (4. 3 gallons/min) Self-priming from dry up to 2. 4m (7. 8ft) Smooth flow. Dry running capability. Soft noise absorbing mounts. Snap-fit port fittings. Corrosion resistant materials. Meets USCG Regulation 183. 410 and ISO 8846 MARINE (ignition protection).
|
Deluxe Windshield Washer Kit from AFI
Install your own windshield washer systemFits new or existing AFI Deluxe wiper arm and blade sets, with all the parts to outfit two wiper arms. The kit includes a 3 liter water tank with mounting bracket (8. 5"H x 7"W x 4. 5"D), 12V pump motor and 16' below deck clear tubing, 6' above deck black tubing, clips and sprayer fittings. You supply wiring, an in-line 3A fuse and On-Off momentary switch.
|
Stainless-Steel Compact Electric Horn - Double from AFI
Mini Twin Electric Horn Excellent for use in the marine environment. totally seal sound units have type 304 stainless cover, diaphragm and mounting brackets. Material: 304 stainless cover & horn diaphragm. Loudness dB: 106 dB. Approvals: ABYC for boats up to 20 meters. Dimensions: 3"L x 8"W x 1 3/4"H. Power Requirements: 12V. Draw: 3A @ 12V (max. 6A). Fundamental frequency: 490±20/440±20.
|
12 Volt White Dual Trumpet Mini Air Horn from AFI
White epoxy powder-coated finish over solid brass. Noncorrosive Lexan® diaphragm. 12vDC. . Draws 20 amps max. Includes compressor, air tubing, fittings, and hardware. 5" W x 3-3/4"H x 9-1/2" L.
|
Outboard Oil - SAE 10W-40 from WEST MARINE
With a higher number of performance-boosting additives than automotive oil, this synthetic blend meets and exceeds the needs of high-performance outboards. It's special formula protects outboards from friction damage and engine wear. Outstanding viscosity at low temperatures. Greater detergency. Resists engine build up. Exceeds all 4-stroke outboard requirements.
|
Synthetic Blend 4-Cycle Engine Oil, Quart from QUICKSILVER
Recommended for gasoline and diesel-powered stern-drive and inboard engines that require FC-W Certified, SAE 25W-40 oil.
|
1/4" NPT X 3/8" Brass hose barb from MOELLER
1/4 NPT X 3/8" Brass Hose barbs with male threads.
|
Flush Kit For 2- & 4-Stroke Outboards from MERCURY MARINE
Fits Mercury/Mariner 4 and 5hp 2-stroke outboards and 4, 5 and 6hp 4-stroke outboards.
|
|
|
Diamond Pad Eye 3-1/4" from SUNCOR
Diamond Pad Eyes. Heavy-Duty, one-piece precision casting.
|
Yamaha Outboard 1984-1996, 1-4 Cyl., V4, V6, 2-250 HP from SELOC PUBLICATIONS
Designed and written to serve the needs of the professional mechanic, do-it-yourself boat enthusiast, instructor and student, these manuals are based on actual teardowns done by Seloc’s editors/authors in our on-site facility. This repair manual covers all Yamaha outboard engines, 12-250 HP, 1-4 cylinder, V4, V6 models, 1990 to 2001. Every manual features: Easy-to-follow, step-by-step, illustrated procedures . Hundreds of exploded drawings, photographs and tables . Troubleshooting sections .
|
|
2-4-C Lube W/Teflon - Three 3.5 oz Grease Gun Cartridges from MERCURY MARINE
A high quality multi-purpose lubricant to withstand extreme friction and also improve water resistance.
|
4-Cup 12V Coffee Maker from WARING
Enjoy fresh coffee ashore or afloat with this 4-cup coffee maker that plugs into any 12V outlet. Features include a durable stainless-steel carafe, dripless pour spout, knuckle guard, 30-minute auto shut off, “On” indicator light, and a convenient “Brew Pause” feature that lets you pour a cup of coffee before brewing has finished. Includes coffee scoop and three filters. 10 1/4"H x 5 1/4"W x 7 5/8"D.
|
1/4" Aluminum Hose Barb, 1/4" Make Thread from MOELLER
Barb-Fuel 1/4Npt x 1/4 M Thrd|Barb-Fuel 1/4Npt x 1/4 M Thrd.
|
|
4" from AFI, 4"H from AFI, Regular from AFI, L from AFTCO, XL from AFTCO
|
|
Home -> Engine Systems -> Horns/Wipers/Glove Boxes -> Horns
Stainless steel diaphragm and mounting bracket . Black polypropylene cover . Dimensions: 4 inches L x 3-3/4 inches W x 2-3/4 inches H . Maximum amp draw: 4 Amps . dB(A) rating: 108 at one meter Fundamental frequency: 350±15 .
Part No: 10023
|
|
|
|
Home -> Engine Systems -> Horns/Wipers/Glove Boxes->2.5 Heavy Duty Wiper Motor
Powers a 26" Deluxe arm and 26" Deluxe blade combination or a 24" Premier arm and 24" Premier blade combination. Fully sealed powdercoated aluminum waterproof base and housing. RF shielded circuitry. Factory pre-set sweep angles of 80° or 110° with easy adjustments of 45° or 60°. 12V electrical system. Two-speed motor. Style: Interior/Exterior. Sweep Direction: Both. Self-Parking: Yes. Case Material: Aluminum. Draw: No-load current 1.
Part No: 82082
|
|
|
|
Home -> Fishing -> Fishing Accessories
High-density polyethylene. Measures 6 1/2''W x 7 1/2''H x 2 1/2''D.
Part No: 65608
|
|
|
|
Home -> Engine Systems -> Horns/Wipers/Glove Boxes -> Horns
Designed for easy installation, this hidden horn mounts from the outside. Compact in size, but capable of 107db loudness. Comes with both black and white snap-on ASA plastic grilles. A weatherproof fabric liner lets sound through, but keeps water out. Prewired for 12V installation. Material: ABS plastic . Loudness dB: 107dB . Design Standards: Meets ABYC specs for boats up to 12 meters . Dimensions: 2"H x 3-3/8"W x 3-1/4"D . Power Requirements: 12 Volts .
Part No: 10079
|
|
|
|
Home -> Electrical -> Shore Power -> Adapters, Plugs & Outlets
Two per pack 5-1/6" x 3-5/8" Plantation grown teak.
|
|
|
|
Home -> Paint & Maintenance -> Epoxy & Fiberglass -> Teak & Starboard->Teak Winch Pads
.
Part No: 60476
|
|
|
|
Home -> Cabin & Galley -> Containers & Storage->Polyethylene Drink or Air Horn Holder
Durable and attractive, these cup holders do double duty as air horn holders - order the insulated models to keep your beverage hot or cold longer! High-density polyethylene.
Part No: 65605
|
|
|
|
Home -> Engine Systems -> Horns/Wipers/Glove Boxes->1.5 Heavy-Duty Wiper Motor
Powers a 22" Deluxe arm and 22" Deluxe blade combination or a 20" Premier arm and 20" Premier blade combination. Fully sealed powdercoated aluminum waterproof base and housing. RF shielded circuitry. Factory pre-set sweep angles of 80° or 110° with easy adjustments of 45° or 60°. 12V electrical system. Two-speed motor. Style: Interior/Exterior . Sweep Direction: Both . Self-Parking: Yes . Case Material: Aluminum . Draw: No-load current 0.
Part No: 71082
|
|
|
|
Home -> Engine Systems -> Horns/Wipers/Glove Boxes->XL Plus Trumpet Horns
These very loud horns are built to last due to their sealed sound units. They feature exclusive over-molded motor housings for extra protection and a longer life than other similar horns. Stainless-steel, rust- and corrosion-proof construction of the key components. Includes an international horn signal card and mounting hardware. Sealed sound unit keeps moisture out.
Part No: 10018XL
|
|
|
|
|
Home -> Engine Systems -> Horns/Wipers/Glove Boxes->XL Plus Trumpet Horns
These very loud horns are built to last due to their sealed sound units. They feature exclusive over-molded motor housings for extra protection and a longer life than other similar horns. Stainless-steel, rust- and corrosion-proof construction of the key components. Includes an international horn signal card and mounting hardware. Sealed sound unit keeps moisture out.
Part No: 10017XL
|
|
|
|
Home -> Interior, Flags & Gifts -> Flags & Staffs
Teak Ensign Staffs Our traditional staffs are made of natural teak. which retains its good looks with a minimum of maintenance.
|
|
|
|
Home -> Engine Systems -> Horns/Wipers/Glove Boxes->AFI-1000 Waterproof Wiper Motor Kit & Wiper Motors
Fully sealed, waterproof housing from UV-stabilized thermoplastic for inside or outside mounting. 12V heavy duty motor with knurled anti-rotation drive shaft and RF-shielded circuitry. 75 lbs. Maximum 18" x 18" arm and blade. AFI 1000 Wiper Kit 37100 includes 37180 motor with 2 1/2" shaft, Deluxe adjustable 10"-14" wiper arm and 14" wiper blade. Separate AFI-1000 motors offer either 110° or 80° sweep range. Sweep Direction: Left or Right.
Part No: 37180
|
|
|
|
Home -> Engine Systems -> Horns/Wipers/Glove Boxes
Constructed of white ABS plastic. Easily installed.
Part No: 33025
|
|
|
|
Home -> Engine Systems -> Horns/Wipers/Glove Boxes -> Wipers->Intelligent Wiper Switches
Microcontroller-based “intelligent switch” provides all the necessary wiper motor functions in one small component. Includes settings for two continuous speed functions (2, 4 and 8 second delay), washer system operation, and blinking LED lights in the switch to indicate operating function. Works with 12V or 24V DC motors. Fits standard size switch openings, and requires 2. 65" (65mm) depth behind panel.
Part No: 76030
|
|
|
|
Home -> Engine Systems -> Horns/Wipers/Glove Boxes->Chrome Trumpet Air Horn
Includes compressor, air tubing, fittings, and hardware Dimensions: 17”L x 3-3/4”W x 3-3/4”H Includes compressor, air tubing, fittings, and hardware Maximum amp draw: 12 Volt: 20 Amps, 24 Volt: 10 Amps.
Part No: 10624
|
|
|
|
|
Home -> Engine Systems -> Horns/Wipers/Glove Boxes -> Wipers->Intelligent Wiper Switches
Microcontroller-based “intelligent switch” provides all the necessary wiper motor functions in one small component. Includes settings for two continuous speed functions (2, 4 and 8 second delay), washer system operation, and blinking LED lights in the switch to indicate operating function. Works with 12V or 24V DC motors. Fits standard size switch openings, and requires 2. 65" (65mm) depth behind panel.
Part No: 76035
|
|
|
|
|
Home -> Engine Systems -> Horns/Wipers/Glove Boxes->Chrome Trumpet Air Horn
Includes compressor, air tubing, fittings, and hardware Dimensions: 17”L x 3-3/4”W x 3-3/4”H Includes compressor, air tubing, fittings, and hardware Maximum amp draw: 12 Volt: 20 Amps, 24 Volt: 10 Amps.
Part No: 10524
|
|
|
|
Home -> Cabinet & Deck Hardware -> Cabinet Hardware & Locks
Offset 1/2" 2 3/4'' long x 2 1/8'' wide Countersunk for #8 fasteners Sold in pairs.
Part No: 60718
|
|
|
|
Home -> Engine Systems -> Horns/Wipers/Glove Boxes -> Wipers
AFI 34015 MRV Heavy Duty 2-Speed Wiper Motor. Easily powers 22" x 22" deluxe arm/blade combinations, or a 20" x 20" premier arm/blade combination at sweep sets of 80° or less. It has a factory pre-set sweep of 80° and is adjustable to 45°, 60°, 80° or 110°. Dimensions: 7-5/8"L x 4"W x 2"D. 12 Volt. 3.
Part No: 34005
|
|
|
|
Home -> Fishing -> Fishing Accessories->Bluefever Utility Glove
Aftco Bluefever Utility Glove For everything from leadering and gaffing to tying knots and filleting, this glove is ideal for every Blue Water Angler. An alll-purpose fishing glove with special Armortex® palm and fingers to add durability, and vent holes to help aid in draining water. Foam backed mesh keeps hands cool and protected. Spandura® with four-way stretch Cordura® forchettes between fingers.
Part No: GLOVEULBLUE
|
|
|
|
|
Home -> Trailer & Parts -> Hitches, Winches & Jacks->Bluefever Shortpump Glove
Bluefever Shortpump Glove M|Bluefever Shortpump Glove M.
Part No: GLOVESPMBLUE
|
|
|
|
A versatile fishing glove that protects your hands Designed and built by fishing enthusiasts who understand the need for high performance fishing gloves. Five specific models for a variety of applications. Each glove is made using the finest quality materials and craftmanship and come in sizes through XX Large - so you're ensured of having the best fit. AFTCO Bluefever Gloves will hold up to the rigors of the fishing environment while maintaining the desired "feel".
Part No: GLOVESPLRXLBLUE
|
|
|
|
Home -> Fishing -> Fishing Accessories
AFTCO’s new Fish Bat is made of molded, glass-filled polypropylene, super strong and corrosion proof, with a special triangular shape that will not roll on the deck of a rocking boat. Features include an aggressive, molded-in textured grip for non-slip performance, a braided rope safety lanyard, and a special handle hook, handy for hanging the bat from a railing or ladder. With a 19-inch length and weighing 1.
Part No: FBAT2B
|
|
|
|
Aftco Bluefever Shortpump LR Glove A lightweight glove with short fingers. with index and middle fingers, plus thumb being longer for added protection. Super tough Armortex® reinforces the glove from fore finger to thumb for the safe handling of synthetic fishing lines. Tacky-Grip palms with vent holes add durability and help drain water. Vented foam-backed mesh keeps hands cool and protected. Perforated neoprene cuff with Velcro® closure for a secure fit.
Part No: GLOVESPLRSBLUE
|
|
|
|
|
Bluefever Wire Max Glove XXL|Bluefever Wire Max Glove XXL.
Part No: GLOVEWMXXLBLUE
|
|
|
|
Home -> Fishing -> Fishing Accessories -> Fishing Belts
Afco Adjustable Nylon Drop Straps Designed to fit all Afco straps.
Part No: STRAP1B
|
|
|
|
Home -> Fishing -> Fishing Accessories->Goldfinger Release Clips
Super-lightweight composite clips feature a numbered, graduated adjustment slider for precise release tension setting. Large diameter, gold titanium-nitride coated wire bail for less line wear and smooth releases. Kite clip can be ''stacked'' or added to kite line any time.
Part No: OCLIPG1B
|
|
|
|
|
Home -> Trailer & Parts -> Hitches, Winches & Jacks->Bluefever Shortpump Glove
Bluefever Shortpump Glove XL|Bluefever Shortpump Glove XL.
Part No: GLOVESPXLBLUE
|
|
|
|
|
Bluefever Sp Lr Glove XXL|Bluefever Sp Lr Glove XXL.
Part No: BFSPLR-12
|
|
|
|
|
Bluefever Wire Max Glove L|Bluefever Wire Max Glove L.
Part No: GLOVEWMLBLUE
|
|
|
