Gen-Sep Water Separator, 2" Diameter, Gas In/Out 2.0", Water Outlet 1.5" from CENTEK INDUSTRIES
Position the water drain from the Gen-Sep just below the water line to eliminate water splash, especially important for nighttime operation. Gen-Sep will remove nearly all of the cooling water from the exhaust. That water can then be drained to a hull fitting just below the waterline, thus eliminating excess noise often created by splashing and pulsating water flow at the exhaust outlet. A slight downward angle is required for both the exhaust outlet and the exhaust gas tube. Dimensions: 10.

BK-1 Replacement BilgeKleen Filter from CENTEK INDUSTRIES
We recommend that filters be checked or changed every 3 months.

Hose Adapter, From 1-1/8" to 3/4"-5/8" from RULE INDUSTRIES
#69 is stepped & adapts from 1-1/8" to 3/4" - 5/8" #57 is an elbow & adapts from 1-1/8" to 1" NPT #67 adapts from 1-1/2" to 1-1/8".

Five Louver Stainless Steel Vent from WHITECAP INDUSTRIES
Mount on doors, bulkheads, in the cockpit and on hatch boards. Helps to eliminate mildew. . Pre-drilled for six #8 screws. . Mfr. 's lifetime limited warranty. . Ship 0. 5 lbs.

110V AC Automatic Bilge Pump from RULE INDUSTRIES
The 1800gph pumping capacity and extra-long 24' power cord make this pump great for boats with shore power or protecting basements from flooding during wet weather. Motor and durable housing will last for years on the boat or in the home. 5/8" garden hose adapter. gph: 1800. Draw: 1. 1A@110V AC. Built-In Switch: Yes. Material: Plastic. Dimensions: 7-3/4" x 4-3/4". Port Size: 1-1/8".

Deck Fill, Gas, w/Key, 1-1/2" from WHITECAP INDUSTRIES
Stainless-steel deck fills with durable cast heads—not the thin stamped heads found on many imports. Gas, Diesel and Water fills have 1 1/2" openings. Waste fill has 2" opening. All connect to 1 1/2" hose, and include a stainless key. Material: Stainless . Attachment Method: 1 1/2" hose . Flange Diameter: 3" or 3 1/2" (waste) . Fasteners: Three #10 FHMS . Cutout Diameter: 1 5/8" .

500gph 12V Bilge Pump, 1.9A Draw at 12V DC, 3/4" Port, 4"H x 2-3/8"W from RULE INDUSTRIES
An internal computer chip cycles these pumps on every 2. 5 minutes, then quickly shuts them down if no water is detected. Built-in strainer bases snap off to make cleaning easy. Completely submersible, rust-proof, corrosion-proof and ignition-protected. Three-way wiring enables connection to a switch for manual override or indicator light. Small 500gph pump is designed to handle spray and rainwater. Built-In Switch: Yes, cycles every 2. 5 min.

500gph 12V Bilge Pump, 3/4" Port, 1.9A Draw, 2.5A Fuse, 3-1/2"H x 2-3/8"W from RULE INDUSTRIES
Tough and reliable at a value price Great performance at a value price, Rule submersible pumps are the first choice for many boat manufacturers. Their motors feature stainless-steel shafts, water cooling and a vibration-free centrifugal impeller that won’t burn out if run dry. Strainer bases can easily be snapped off for cleaning. Each pump requires a panel switch for manual operation or a float switch for automatic operation. Select from 12V, 24V and 32V models. Can run dry without damage.

Rule-A-Matic Plus Float Switch from RULE INDUSTRIES
Is the float switch working? It's easy to check! Features a Rule-A-Matic float switch and an impact-resistant cover to protect against debris and jamming. Wiring is "blocked" by a rubber grommet to provide strain relief. Includes a convenient feature for manual tests. Activation Method: Float with mechanical contacts. Dimensions: 2-3/4"H x 2-1/2"W x 4-7/8"L. Capacity: 20A @ 12/24/32V DC.

Strainer for Round Rule Pump, 2800 - 3700 gph Flow Rate from RULE INDUSTRIES
Original replacement strainer base for your Rule Bilge Pump.

3-Way Lighted Rocker Panel Switch from RULE INDUSTRIES
Controls any pump equipped with an automatic float switch. This unit features a black plastic panel. It has a built-in fuse holder and an internally lighted rocker switch with 3 positions (automatic, off, or manual) with the Rule "fail-safe" spring return to "off" from the "manual" position.

Slimline 500Gph Pump Kit from RULE INDUSTRIES
Portable pump goes where the water is and gets rid of it fastThese hand-deployed, submersible pumps are perfect for pumping out hard-to-reach places where water collects. No slouch when it comes to capacity, they are capable of pumping 500gph and generating a 13-foot head. Powered by your boat's 12V system, they work great for diesel or water transfer, deck showers, washdowns, and baitwell tank aeration. Purchased alone, pumps include a 13-foot power cable with battery clips.

Wash-N-Rinse Spray Gun from BON-AIRE INDUSTRIES,
Connect this no-nonsense spray wand to a standard garden hose for efficient washdowns of your boat or car. Features a rubberized pistol-grip handle/soap dispenser with adjuster for spray intensity and soap release. 24" long wand works great for point-blank blasting of formerly hard-to-reach dirt on deck.

Rule 500GPH Transom Mount Bait Pump from RULE INDUSTRIES
Transom mounted aerator pumps provide your livewell to have professional aeration without needing to install a pump through your hull. The unique quick-release pump with strainer base assembly snaps easily into the provided transom bracket. At the end of the day, the pump can be removed from storage. Each pump features 6' wire leads. No need to install a pump through the hull. Unique, quick-release pumps with strainer base assembly easily snap into the transom bracket (included).

26" Destroyer Wheel from EDSON CORPORATION
These 5-spoke wheels are the latest addition to Edson’s line of Destroyer™ Wheels. Attractive, dished shape and newly-styled, straight hub. Tapered, hollow spokes. Lightweight 1" ovalized grip tubing is the industry standard for smooth wheel steering. 1" bore fits most Edson wheel shafts. Requires Wheel Nut fastener.