Bulk Pak Nylon Washers - 1/4", Pack of 100 from FASCO FASTENERS
These washers are white nylon for cushioning.

Rounded Oval, 8-1/2"W x 11-1/4"L x 5-1/4"D, 1" Flange, 1-1/2" Drain from AMBASSADOR MARINE
Made from 304 stainless steel and mirror-polished to a deep luster, these sinks incorporate SoundKOTE Noise Reduction Technology to reduce the unpleasant clanging associated with many metal sinks. Flanges permit over- or under-the-counter mounting. Low-Profile 90° drains fit standard 1"ID hose and are slanted to maximize drainage.

Replacement Delrin Roller, 2-1/2" Dia., 1-3/4 Width from LEWMAR
Anchor rollers make dropping and weighing anchor easier on you and your boat. They help reduce chafe, prevent scratches and dings to your boat’s finish and provide a secure place to store your anchor when used in conjunction with an optional chain stopper or tensioner. We stock rollers to fit the most common combinations of anchor, mounting style and boat. Installation note: overhanging anchor rollers should be supported along at least 2/3 of their length. Easily installed using common tools.

Delrin Sheave, 1/2" Max. Line Dia., 1-7/16" OD, 3/8" ID, 5/8" Width from SCHAEFER
Schaefer sheaves are designed to be compatible with Schaefer products, and are not intended for use in other manufacturer's blocks. Delrin sheaves are injection molded with UV inhibitors and monitored molding cycles for a stronger product.

Exit Box Style, 7/8" Sheave Dia., 1/8" Max. Line, 350lb. SWL, 1.1oz. from RONSTAN
.

P-Trap Fuel Surge Protector from ATTWOOD
One combined product eliminates the need to install both a fuel line vent and a surge protector. Inertia of surging fuel drives the surge ball against upper seat, closing the large vent opening and limiting passage to smaller openings, which reduces fuel flow and minimizes spillage. Operates in any orientation within 45° of vertical. Baffles resist water intrusion during normal sea conditions and washdown. Constructed of glass filled polypropylene to withstand oil, gas, alcohol blended fuels.

Roller Shaft Cap Nuts Only - 1/2", Pack of 8 from C E SMITH
Roller Size Length Shaft Diameter Shafts and Nuts 4" 5 1/4" 1/2" 4" 5 1/4" 5/8" 5" 6 1/4" 1/2" 5" 6 1/4" 5/8" 8" 9 1/4" 5/8" 10" 11 1/8" 5/8" 11" 12 3/4" 1/2" 12" 13 1/2" 5/8" Shaft Only 18" 19" 5/8" Cap Nuts Only Packs of 8.

Adjustable Packing Nut Wrench from SEAFIT
Better than a pipe wrench If you are not equipped with wrenches that fit the nuts on your stuffing box, we suggest you purchase TWO of these. Why? Because you will need two to make an adjustment: One for the locking nut and one for the adjusting nut. These wrenches tend to be easier to use than pipe wrenches—especially in tight engine spaces where many boaters must work. Primary Usage: Adjust/remove inboard shaft packing nut . Size: 1" to 3" adjustable .

50' Braided Polyester Cord from NEW ENGLAND ROPES
A low-stretch cord that’s great for flag halyards, foredeck netting, or light-air spinnaker sheets. Length: 50'. Diameter: 1/8". Best use: Utility cord, flag halyards . Construction: Braided polyester . Breaking strength: 530lb. . Stretch: 3% at 15% of breaking strength .

Series 150 Clear PVC Tubing, 1/2"ID, 45psi Burst Pressure from SHIELDS RUBBER
Single layer, nontoxic, FDA-approved clear vinyl tubing. Ideal for drain lines, iceboxes, refrigerators, livewells, bilge pump discharge, freshwater lines, water and holding tank vents. Sold per foot: 50’ maximum continuous length for 1/4" and 3/8" hose; 100' maximum continuous length for 1/2" hose and larger. Application: Non-pressurized water system supply; sink, shower, and icebox drains. Material: FDA formula vinyl. Reinforcement: None. Temperature Range: N/A.

1/4" Dia. Stamped Halyard Shackle, 1,000SWL from SCHAEFER
Stamped Halyard Shackles haveflared heads with cross pin retainer for attachment to rope. Captive design prevents accidental opening Quick release pin #93-42 - 1/4" Shackle Pin dia. , 1/2" Inside Width, 1,000 SWL #93-45 - 5/16" Shackle Pin dia.

1-7/8" Polished Brass Flush Ring Pull from ABI
Highly polished brass . Convenient flush-fitting ring pull for cabinets, small doors, and hatches. . 1-7/8"L x 1-1/2"w . Requires four #5 fasteners .

PE-1 Lexan Mast Pad Eye from FORESPAR
For use on our small poles. 1-3/4"H x 1-1/4" x 5/8"dia. ring. Same ring as supplied with 4-8 and 6-12 poles.

Stern Rail Outboard Motor Mount - Aluminum for 1-1/4" Railings from EDSON CORPORATION
Built to hold motors up to 15 hp or 100 lbs/45 kg. Convenient cleat and side handles allow you to tie the motor and lock it safely on board. The non-corroding polished 316 stainless bracket with non-skid pad, bolted to the UV stable poly backing board always looks ship-shape… no more varnishing. Bottom cleat comes unattached so that it will fit any rail spacing. Note: 1-1/4” rail version comes complete with anodized aluminum bracket, stainless cleat and stainless U-bolt for 1-1/4” railing.

Clamp-On Rod Holder - 1 1/4"ID Horizontal, Gold from WEST MARINE
1 1/4IN HORIZONTAL MOUNT.