Top Sellers
Flush Kit For 2- & 4-Stroke Outboards from MERCURY MARINE
Fits Mercury/Mariner 4 and 5hp 2-stroke outboards and 4, 5 and 6hp 4-stroke outboards.
|
Replacement Delrin Roller, 2-1/2" Dia., 1-3/4 Width from LEWMAR
Anchor rollers make dropping and weighing anchor easier on you and your boat. They help reduce chafe, prevent scratches and dings to your boat’s finish and provide a secure place to store your anchor when used in conjunction with an optional chain stopper or tensioner. We stock rollers to fit the most common combinations of anchor, mounting style and boat. Installation note: overhanging anchor rollers should be supported along at least 2/3 of their length. Easily installed using common tools.
|
Furler Kit for Boat Length to 16', 500lb. SWL, 1/8" Max. Wire dia., 1/4" Pin dia., 2-1/2" Pin-to-Pin, 5/32" Furling Line dia. from HARKEN
Furl or set your jib from your cockpit Harken small boat furlers allow the sail to be set and furled from the cockpit, a critical convenience in many racing dinghies and trailerable sailboats. Constructed of Hardkote anodized Teflon-impregnated aluminum, they feature multiple stacked races of Delrin or Torlon ball bearings for smooth rotation under load. The jib’s luff wire must be properly seized to the sail, since it carries most of the headstay load. 434 furler for dinghies under 16ft. (4.
|
G. O'Day 222/Santana 525,Length 47", Height at tip 2 1/4", Width at butt 1 1/2", Width at tip 2" from WEST MARINE
Replace that old ugly tiller with a new hand-made laminated ash and mahogany wood tiller, made to fit your rudder hardware, and pre-finished with multiple coats of premium marine spar varnish. Choose the right length and profile, and the butt-end measurements to fit your rudderhead hardware. Can’t find a good fit? Idasailor Marine can custom-build a tiller to your measurements . Custom tillers are shipped direct within 10 days . Click HERE to open the PDF custom order form.
|
|
|
Covered Waterproof Foot Switch from WEST MARINE
Hinged safety cover closes over the switch to prevent accidental operation. 150A continuous rating. 4'' dia. Cutout: 2. 5'' dia.
|
Adapter—3/4" BSP Female to 15mm (Qty. 2) from WHALE PUMPS
Just cut the tubing to length and fully push the end into the appropriate fitting. The collet automatically secures the hose. If you ever need to alter the system, the connections can be disassembled and reused. All components are manufactured from nontoxic, food-grade materials and are designed to allow unrestricted flow. To gain the advantages of the Whale system, it is not necessary to replumb your entire boat, as unique adapters enable connection to most boat’s existing plumbing systems.
|
Off/1/All/2 Battery Switch, 380 Continuous Amps, 850 Intermittent Amps from PERKO
For high-amperage applications like diesel engine starters, large inverters and windlasses. Reinforced polycarbonate body, 1/2"dia. brass terminal connections and an alternator field disconnect. Alt. Field Disc. : Yes . Switch Material: Reinforced Polycarbonate. Terminal Material/Size: Brass 1/2"dia. . Switch Dimensions: 5-1/4"sq. x 3-3/8"H .
|
|
|
PE-1 Lexan Mast Pad Eye from FORESPAR
For use on our small poles. 1-3/4"H x 1-1/4" x 5/8"dia. ring. Same ring as supplied with 4-8 and 6-12 poles.
|
Hose Adapter, From 1-1/8" to 3/4"-5/8" from RULE INDUSTRIES
#69 is stepped & adapts from 1-1/8" to 3/4" - 5/8" #57 is an elbow & adapts from 1-1/8" to 1" NPT #67 adapts from 1-1/2" to 1-1/8".
|
|
|
Hatch - Ocean 60 Flat Base from LEWMAR
Well-engineered hatches with CE-certified quality materials and construction. Smoothly styled external hinge enables one-hand operation. Inside handles feature locks that cannot be forced from the outside. Flat base or 1'' flange base (pictured). 3-year warranty. Flat base cutout sizes: Ocean 10 - 10" x 10". Ocean 20 - 7-3/4"W x 13-1/2"L. Ocean 30 - 12-5/8"W x 17-3/4"L. Ocean 40 - 16-3/8" x 16-3/8". Ocean 44 - 17-3/16" x 17-3/16".
|
12 Gallon Topside Fuel Tank from MOELLER
Made from marine grade cross-linked polyethylene for light weight and durability, all tanks are USCG, NMMA and ABYC compliant. Mechanically vented cap floats, and is easy to grip, with ribbed design. Tank includes 90° 1/4"NPT Moeller patented “Poplock” aluminum withdrawal elbow. It swivels 360° without losing its seal. Injection molded 2 1/4" fill neck with gauge and vent. 43"L x 15"W x 6"H.
|
Drill Pump Kit from JABSCO
The self-priming drill pump chucks into a standard 1/4" drill motor and pumps up to 3 1/2gpm. Kit includes all items needed for draining engine oil through the dipstick tube. Includes 3' of 1/2" hose, probe adapter and 40"L x 1/4"dia.
|
|
from FORESPAR, 1, 1-1, 4" from FORESPAR, 2-1, 2, 2", 2, Plastic from FORESPAR
|
|
Home -> Plumbing -> Freshwater Systems->Sink Drain Fittings
null.
Part No: 907000
|
|
|
|
Home -> Sailboat -> Downwind Poles & Cars -> Pole End Fittings & Tub->TS Series Socket Ends
Aluminum fitting automatically locks onto the mast toggle pin.
Part No: 309028
|
|
|
|
Home -> Plumbing -> Fittings & Valves->Marelon Ball Valves & Tailpieces
A. Marelon Ball Valves - High-strength, lightweight glass-reinforced Marelon. After 11,000 duty cycles, they still hold 80psi of air leak-free. B. MarelonTailpieces - Hose barbs on one end. NPS pipe threads on the other. C.
Part No: 901002
|
|
|
|
Home -> Plumbing -> Freshwater Systems->Sink Drain Fittings
null.
Part No: 907027
|
|
|
|
Home -> Sailboat -> Tiller & Rudder -> Tillers Extensions & Ac->Big Stick Carbon Fiber Tiller Extensions
'Big Stick' Carbon Fiber Tiller Extension Rugged, light weight tiller extensions made for go-fast dinghy or keel boat. Extensions are shipped loose for custom lengths to suit your class requirements. 7/8" diameter shaft for a solid grip for either men or women. . Straight tubes for easy modification and tailoring. Proven "speed lock" design for 360° of rotation without binding. Quick mount⁄dismount, and easy replacement if necessary.
Part No: 102217
|
|
|
|
Home -> Sailboat -> Tiller & Rudder -> Tillers Extensions & Ac->Giant Stick Tiller Extensions
"Fat 1 ¼" diameter extension allows you to use a light grip for great feel and so your hand doesn’t get fatigued. 48" length is great both for the Laser and U20 sportboat. " Exceptional holding power in a super lightweight blockThe Series 60 is a good choice for Lasers and mainsheets on dinghies, Series 75 is sized for mainsheets on larger, powerful dinghies, skiffs and sportboats of all sizes, or for asymmetrical spinnaker sheets. Machined cheeks and sheave.
Part No: 102227
|
|
|
|
Home -> Sailboat -> Downwind Poles & Cars->Heavy-Duty Telescoping Twist-Lock Poles
These telescoping whisker poles are heavy-duty two-section and three-section aluminum spars which can be extended to lengths up to 17' and securely locked in position by an internal twist lock device. Poles feature self-latching Ultra Series™ fittings on the inboard and outboard ends. Aluminum tubing. End Fitting Inboard: UPX. End Fitting Outboard: UPX.
Part No: 407101
|
|
|
|
Home -> Sailboat -> Shackles, Snaps & Fittings->Spinnaker Shackle Guards
Place a protective buffer between the spinnaker pole ends and your after-guy shackle. Shackle guards can also be used on lifelines to help skirt genoas. High strength polyethylene. UV inhibited for long life.
Part No: 300087
|
|
|
|
|
Home -> Sailboat -> Shackles, Snaps & Fittings->Spinnaker Shackle Guards
Place a protective buffer between the spinnaker pole ends and your after-guy shackle. Shackle guards can also be used on lifelines to help skirt genoas. High strength polyethylene. UV inhibited for long life.
Part No: 300091
|
|
|
|
Home -> Sailboat -> Rigging Products -> Shroud Covers, Mast Boots
The unique patented design of these jib rollers makes them easy to snap on around stays and lifelines to protect your sails from chafe. When used on lifelines, Sail Savers™ help skirt the foot of the jib. They can also be used on the backstays of catamarans or other boats with large roached mainsails. Center hole is 3/16" and can be drilled out to 3/8" maximum. Two halves slide together and lock in place while two included safety clips snap on for added security.
Part No: 210020
|
|
|
|
High performance spring-loaded mechanical vang for racing or cruising The Yacht Rod‘s hardened stainless spring provides the upward force necessary to support your boom in light air or when lowering the mainsail. For downward force, the block and tackle system provides efficient control of leech tension with 8:1 purchase. Tackle, Harken Blocks and mast/boom fittings included. Precipitation-hardened stainless steel spring with Fastpin adjustment is rated for over one million compression cycles.
Part No: 352050
|
|
|
|
Home -> Sailboat -> Downwind Poles & Cars
Separates the up/down and side-to-side motions of the pole to make a bind-free, strong attachment. Shackles are supplied for uphaul/downhaul lines. Stainless steel cheeks, aluminum body and plastic liners. Ring Style Car RC-125 Although a screw-pin stop is supplied, this car is designed to be used with uphaul/downhaul blocks shackled to the bails at each end. Ring ID: 1 5/8". Investment cast stainless steel with plastic liners to reduce friction. Fits UXP and UTR pole end fittings.
Part No: 331000
|
|
|
|
|
Home -> Sailboat -> Downwind Poles & Cars->Heavy-Duty Telescoping Twist-Lock Poles
These telescoping whisker poles are heavy-duty two-section and three-section aluminum spars which can be extended to lengths up to 17' and securely locked in position by an internal twist lock device. Poles feature self-latching Ultra Series™ fittings on the inboard and outboard ends. Aluminum tubing. End Fitting Inboard: UPX. End Fitting Outboard: UPX.
Part No: 406300
|
|
|
|
|
Home -> Sailboat -> Shackles, Snaps & Fittings->Spinnaker Shackle Guards
Place a protective buffer between the spinnaker pole ends and your after-guy shackle. Shackle guards can also be used on lifelines to help skirt genoas. High strength polyethylene. UV inhibited for long life.
Part No: 300085
|
|
|
|
Home -> Sailboat -> Downwind Poles & Cars -> Pole End Fittings & Tub
Stow your pole vertically along your mast where it’s ready to go and out of the way. Urethane chock secures your 3-1/2"dia. pole to the forward side of your mast.
Part No: 300073
|
|
|
|
|
High performance spring-loaded mechanical vang for racing or cruising The Yacht Rod‘s hardened stainless spring provides the upward force necessary to support your boom in light air or when lowering the mainsail. For downward force, the block and tackle system provides efficient control of leech tension with 8:1 purchase. Tackle, Harken Blocks and mast/boom fittings included. Precipitation-hardened stainless steel spring with Fastpin adjustment is rated for over one million compression cycles.
Part No: 352160
|
|
|
|
Home -> Sailboat -> Downwind Poles & Cars -> Spinnaker Poles & Gear->Stanchion Mount Pole Chocks
Stop stumbling over deck-mounted poles and free up space on deck. Non-rusting molded urethane chocks mount easily on 1"dia. stanchions without drilling. You need two per pole.
Part No: 300050
|
|
|
|
Home -> Sailboat -> Downwind Poles & Cars -> Pole End Fittings & Tub->Ultra Series Spinnaker Pole Ends
Lightweight and durable, these composite fittings weigh significantly less than metal fittings. Available with either external or internal trip. Included trip line is lightweight Spectra. All lengths to fit standard poles.
Part No: 304051
|
|
|
|
Home -> Sailboat -> Downwind Poles & Cars->Line Control Whisker Poles
Line Control Whisker Poles Forespar manufactures the finest and most complete selection of whisker poles. Built from heavy-gauge anodized aluminum, high-modulus carbon fiber, or combining an aluminum outer tube with a carbon inner pole, with either Line Control or Twist Lock telescoping systems. It is not necessary to go forward to adjust buttons of any kind—simply uncleat the line to extend or retract.
Part No: 403200
|
|
|
|
|
Home -> Sailboat -> Downwind Poles & Cars->Line Control Whisker Poles
Line Control Whisker Poles Forespar manufactures the finest and most complete selection of whisker poles. Built from heavy-gauge anodized aluminum, high-modulus carbon fiber, or combining an aluminum outer tube with a carbon inner pole, with either Line Control or Twist Lock telescoping systems. It is not necessary to go forward to adjust buttons of any kind—simply uncleat the line to extend or retract.
Part No: 401106
|
|
|
|
Home -> Sailboat -> Tiller & Rudder
For boats up to 22', the Swivel Stick is an economical fixed-length tiller extension. Features a removable Speed Lock rubber universal end fitting. . 5/8" dia. black anodized aluminum tubing with a rubber ball-style handle. . Made in U. S. A. . Mfr.
Part No: 102002
|
|
|
|
Home -> Plumbing -> Fittings & Valves -> Valves, Deck Fills, Misc.->Marelon Intake Scoop Strainers
Made of durable composite material and engineered to exceed ABYC and ISO standards.
Part No: 906061
|
|
|
|
Home -> Sailboat -> Downwind Poles & Cars -> Pole End Fittings & Tub->Twist-Lock Pole Repair Kits
Contains all parts to recondition twist-lock telescoping poles, and complete instructions.
Part No: 400010
|
|
|
|
Home -> Plumbing -> Freshwater Systems->Sink Drain Fittings
null.
Part No: 907022
|
|
|
|
|
Home -> Sailboat -> Downwind Poles & Cars -> Pole End Fittings & Tub->Ultra Series Spinnaker Pole Ends
Lightweight and durable, these composite fittings weigh significantly less than metal fittings. Available with either external or internal trip. Included trip line is lightweight Spectra. All lengths to fit standard poles.
Part No: 304050
|
|
|
|
Home -> Sailboat -> Downwind Poles & Cars->Aluminum Pole Tubing
Prime marine alloy 6063-T6 aluminum.
Part No: 301024
|
|
|
|
Home -> Sailboat -> Tiller & Rudder
Holds any ball-grip adjustable tiller extension in place for short periods of self-steering. Adjustments are made by adjusting your tiller extension length.
Part No: 100000
|
|
|
|
|
Home -> Sailboat -> Shackles, Snaps & Fittings->Spinnaker Shackle Guards
Place a protective buffer between the spinnaker pole ends and your after-guy shackle. Shackle guards can also be used on lifelines to help skirt genoas. High strength polyethylene. UV inhibited for long life.
Part No: 300008
|
|
|
|
|
Home -> Plumbing -> Fittings & Valves->Marelon Ball Valves & Tailpieces
A. Marelon Ball Valves - High-strength, lightweight glass-reinforced Marelon. After 11,000 duty cycles, they still hold 80psi of air leak-free. B. MarelonTailpieces - Hose barbs on one end. NPS pipe threads on the other. C.
Part No: 905010
|
|
|
|
Home -> Sailboat -> Tiller & Rudder -> Tillers Extensions & Ac->Tiller Clips
Tiller Clips Molded of Marelon® for exceptional strength.
Part No: 941020
|
|
|
