Top Sellers
Flex Trim - Black 1/2" opening from TACO PRODUCTS
For a beautiful finished look on unfinished edges. Just push it on and it's on to stay. Grips on difficult materials, compound curves, etc. Individual corrosion resistant aluminum clips for a permanent grip. Black or White . Sold in 25' lengths. . Available in four sizes:. 5/32" opening x 35/64"H. 1/4" opening x 1/2"H. 3/8" opening x 5/8"H.
|
Teak Plugs - 3/8" from SEAFIT
Use these teak plugs to cover screw heads or fill small holes for a beautiful smooth finish to your installation. Sizes: 1/4" 5/8" 5/16" 3/8" 1/2" 1".
|
Roller Shaft Cap Nuts Only - 1/2", Pack of 8 from C E SMITH
Roller Size Length Shaft Diameter Shafts and Nuts 4" 5 1/4" 1/2" 4" 5 1/4" 5/8" 5" 6 1/4" 1/2" 5" 6 1/4" 5/8" 8" 9 1/4" 5/8" 10" 11 1/8" 5/8" 11" 12 3/4" 1/2" 12" 13 1/2" 5/8" Shaft Only 18" 19" 5/8" Cap Nuts Only Packs of 8.
|
Series 150 Clear PVC Tubing, 1/2"ID, 45psi Burst Pressure from SHIELDS RUBBER
Single layer, nontoxic, FDA-approved clear vinyl tubing. Ideal for drain lines, iceboxes, refrigerators, livewells, bilge pump discharge, freshwater lines, water and holding tank vents. Sold per foot: 50’ maximum continuous length for 1/4" and 3/8" hose; 100' maximum continuous length for 1/2" hose and larger. Application: Non-pressurized water system supply; sink, shower, and icebox drains. Material: FDA formula vinyl. Reinforcement: None. Temperature Range: N/A.
|
Deck Fill, Gas, w/Key, 1-1/2" from WHITECAP INDUSTRIES
Stainless-steel deck fills with durable cast heads—not the thin stamped heads found on many imports. Gas, Diesel and Water fills have 1 1/2" openings. Waste fill has 2" opening. All connect to 1 1/2" hose, and include a stainless key. Material: Stainless . Attachment Method: 1 1/2" hose . Flange Diameter: 3" or 3 1/2" (waste) . Fasteners: Three #10 FHMS . Cutout Diameter: 1 5/8" .
|
|
|
Fiberglass Boat Cleaner 920 1/2 Gallon from COLLINITE
Removes rust, exhaust, oil, grease, and oxidation stains from fiberglass. Restores the original color quickly without hard rubbing or buffing, leaves a chemically clean surface to which waxes can bond. Use with fiberglass boat wax or heavy-duty paste Fleetwax . Made in U. S. A.
|
1-7/8" Polished Brass Flush Ring Pull from ABI
Highly polished brass . Convenient flush-fitting ring pull for cabinets, small doors, and hatches. . 1-7/8"L x 1-1/2"w . Requires four #5 fasteners .
|
Off/1/All/2 Battery Switch, 380 Continuous Amps, 850 Intermittent Amps from PERKO
For high-amperage applications like diesel engine starters, large inverters and windlasses. Reinforced polycarbonate body, 1/2"dia. brass terminal connections and an alternator field disconnect. Alt. Field Disc. : Yes . Switch Material: Reinforced Polycarbonate. Terminal Material/Size: Brass 1/2"dia. . Switch Dimensions: 5-1/4"sq. x 3-3/8"H .
|
Hose Adapter, From 1-1/8" to 3/4"-5/8" from RULE INDUSTRIES
#69 is stepped & adapts from 1-1/8" to 3/4" - 5/8" #57 is an elbow & adapts from 1-1/8" to 1" NPT #67 adapts from 1-1/2" to 1-1/8".
|
Series 60 Orbit Block, Single Light-Load, 2-3/8" Sheave Size, 1,710lb. SWL, 4.7oz. from RONSTAN
These exceptionally strong blocks feature the performance Orbit sheave with captive Acetal ball bearings for side thrust loads, eliminating the need for side retainer plates. The 75mm webbing block (RF79107) can be used where swivel head and shackle attachment is not required to achieve further weight savings. Sheave Size: 2-3/8" (60mm) or 3" (75mm). Line Diameter: Series 60: 1/2" (12mm), Series 75: 9/16" (14mm). Cheek Material/Finish: Anodized aluminum.
|
West Marine/SOSpenders PFD Rearming Kit, 3/8" Threaded Cylinder Neck Dia. from WEST MARINE
West Marine/SOSpenders PFD Rearming Kit Style: Automatic. Cylinder Weight: 38g. Cylinder Neck Diameter: 3/8" or 1/2" threaded. Inflator Type: Halkey-Roberts. Kit Contents: Cylinder, green pin, bobbin. PFD Brands Commonly Used With*: West Marine/SOSpenders PFD . Inflator Number: V85000. *The column "PFD Brands Commonly Used With" is not all inclusive. Rearming Kits may be used with other brands and vests.
|
|
|
Flipper Pump from WHALE PUMPS
Easy back-and-forth action produces one-way discharge. Spout swivels. Made of nylon, aluminum and synthetic rubber. For 1/2"ID hose. Material: Nylon, aluminum, rubber . Capacity: 2gpm . Dimensions: 7-1/8"H x 6"dia. . Cutout Size: 2". Clearance: 4-1/2" .
|
Hatch - Ocean 60 Flat Base from LEWMAR
Well-engineered hatches with CE-certified quality materials and construction. Smoothly styled external hinge enables one-hand operation. Inside handles feature locks that cannot be forced from the outside. Flat base or 1'' flange base (pictured). 3-year warranty. Flat base cutout sizes: Ocean 10 - 10" x 10". Ocean 20 - 7-3/4"W x 13-1/2"L. Ocean 30 - 12-5/8"W x 17-3/4"L. Ocean 40 - 16-3/8" x 16-3/8". Ocean 44 - 17-3/16" x 17-3/16".
|
|
from HARKEN, 5oz, 0oz, 3oz, 13oz, 0oz, 0, 8, 2300lb, 1, 2" Length, 16" x 1-3, 200
|
|
Home -> Sailboat -> Traveler, Tracks & Vang -> Mainsheet Traveler->Small Boat Traveler Track & Accessories
Accepts all Harken Small Boat cars. Use low-beam when track is supported at each fastener hole. High-beam can span unsupported areas. Holes on 100mm centers.
Part No: 173
|
|
|
|
Home -> Sailboat -> Blocks->Bullet Blocks
Available in a wide range of designs, bullet blocks are the foundation of the Harken line, and are adaptable to almost all control line applications. Ideal for cunninghams, vangs, outhauls, traveler controls, spinnaker controls, barberhaulers, etc. Where applicable, blocks use #10 fasteners. Sheave: Delrin® . Ball Bearings: Delrin® . Sheave Size: 1 1/8" (29mm) . Line Dia: 5/16" max. . Cheek Material/Finish: Plastic with stainless strap . Cleat: 094, 095, 291- 423 Carbo-Cam® .
Part No: 167
|
|
|
|
Home -> Sailboat -> Blocks -> Blocks->2.25" Blocks
The original Harken block Used for main and jib sheets on course racing keelboats, scows and dinghies with large mains. Often used for spinnaker halyards and sheets on small offshore boats. Swivel blocks feature a three-way head system with a set screw. Blocks with cams feature adjustable cam arms and reversible cam cleats. Where applicable, blocks use #8 fasteners. Sheave: Delrin. Bearings: Delrin ball bearings. Sheave Size: 2-1/4" (57mm). Line Diameter: 7/16" max.
Part No: 004
|
|
|
|
Home -> Sailboat -> Blocks->16mm AirBlocks®
AirBlocks have a lightweight design and a unique patented bearing system which uses stainless steel balls in a captive, grooved race. Very high working loads in an extremely lightweight block, with the best strength-to-weight ratios around. Sheave: Delrin. Sheave Size: 5/8" (16mm). Ball Bearings: Stainless. Line Diameter: 7/32" max.
Part No: 405
|
|
|
|
Sleek dinghy sheet blocks or control blocks on larger boats. Low-profile in-head shackle (on non-swivel blocks) can be upset. Light-duty use only—not meant for use on heavy course-racing keelboats or scows. Where applicable, blocks use #8 fasteners. Sheave Size: 1-3/4" (44mm). Ball Bearings: Delrin ball bearings. Line Diameter: 3/8" max. Cheek Material/Finish: Plastic/stainless. Shackle/Strap Type: In-head shackle; minimizes block length; dual-axis orientation.
Part No: 046
|
|
|
|
Home -> Sailboat -> Blocks -> Blocks->Rope/Wire Bullet Blocks
Designed for vangs, outhauls, shrouds where wire is used or for rope where loads are too high for regular bullet blocks. Roller bearings handle high loads better than ball bearings. Where applicable, blocks use #10 fasteners. Sheaves are aluminum for strength. Sheave: Teflon® impregnated Hardkote anodized aluminum . Bearings: Delrin® roller bearings . Sheave Size: 1-1/8" (29mm) . Line Dia. 5/16" max. . Cheek Material/Finish: Plastic with stainless strap .
Part No: 106
|
|
|
|
Home -> Sailboat -> Cleats & Stoppers->Standard Cam Cleats and Accessories
Harken Cam-Matic cleats are legendary for smooth operation when holding and releasing control lines. Three rows of Delrin ball bearings allow the jaws to open and close smoothly under the highest loads. Light springs allow the cleats to open freely, so the teeth do not have to be sharp which means that your line lasts longer. Use models with aluminum jaws for high loads, or when the line will be drawn through the teeth for adjustment.
Part No: HSB56
|
|
![2" Stand-Up Spring, Fits All Small Blocks from HARKEN]( "2\" Stand-Up Spring, Fits All Small Blocks from HARKEN")
|
|
Home -> Sailboat -> Blocks->Block Accessories
Ball-and-socket bases allow blocks to articulate so they lead fairly from any direction to any direction. Stanchion base mounts to any 7/8" or 1"dia. stanchion .
Part No: 071
|
|
|
|
Home -> Sailboat -> Blocks->Big Bullet Blocks
Can be used as main or jib sheet blocks on dinghies, or for control line applications, such as travelers, cunninghams or boom vangs on offshore boats. Where applicable, blocks use #10 fasteners. Sheave: Delrin. Sheave Size: 1-1/2" (38mm). Ball Bearings: Delrin. Line Diameter: 3/8" . Cheek Material/Finish: Plastic/stainless straps.
Part No: 127
|
|
|
|
Home -> Clothing Accessories -> Gloves->3/4 Finger Sailing Gloves
"They stay soft and flexible better that gloves made from Amara synthetic leather. " Perfect for Dyneema, Vectran and other synthetic line. The grip and durability of the Black Magic® palm material is superior to other sailing gloves. Nylon Spandex mesh for super fit. Minimal stretch when wet. Dries soft. Imported. Dinghy and inshore performance sailing . Configuration: 3/4-finger . Elastic wristbands, adjustable Velcro tabs . Gray/Black .
Part No: 2563L
|
|
|
|
Home -> Sailboat -> Traveler, Tracks & Vang -> Mainsheet Traveler->Midrange Captive Ball Traveler Cars
Recirculating ball-bearing travelers move freely under non-vertical loads and have a low-profile design. Captive balls allow easy installation. Built for high loads on offshore cruisers and racers. Toggle cars are designed with low pivot points for efficient load transfer and serve as a stand-up for mainsheets. Application: Mainsheet systems, offshore boats 27' to 34'. Ball Bearings: Recirculating captive Torlon bearings in open races. 1617, 1618. Material: Machined one-piece aluminum car.
Part No: 1636
|
|
|
|
Home -> Sailboat -> Blocks->ESP Blocks
Designed to handle the high loads generated by modern racing and cruising boats, ESP blocks feature axle bearings to ensure smooth, hitch-free performance under high load and heavy winds. Sheave: Long-glass engineered plastic, except lockoff: aluminum. Bearings: Contained-axle sleeve and carbon-black Torlon ball bearings. Sheave Size: 3" (76mm). Line Diameter: 3/4".
Part No: 6084
|
|
|
|
Home -> Sailboat -> Blocks->75mm Carbo Ratchamatic Blocks
Control loaded lines with ease The 57mm and 75mm Carbo Ratchamatic blocks are adjustable for use in many applications and weather conditions. This load-sensing ratchet block rolls freely in both directions under low loads, then engages the ratchet automatically as loads increase. Great for asymmetrical spinnakers when you need tough holding power and a quick release. Sheave Size: 1-9/16" (40mm). Ball Bearings: Engineered plastic in fitted ball races. Line Diameter: 3/8" .
Part No: 2685
|
|
|
|
Home -> Cordage -> Rigging Products -> Rigging, Sewing, Splicing
Old-fashioned spring gauges, like the Loos Pro, don’t provide repeatable numbers. This product does. Unlike spring-loaded gauges, the Harken Rigtune Pro measures rig tension to the nearest kilogram. A load cell records the pressure on one of the pins and the measurement is displayed on a simple, easy-to-read screen. The Rigtune Pro fits a specific range of rigging sizes, 2. As rigging is deflected over three pins on the back of the gauge, a load cell records the pressure on one of the pins.
Part No: 7850
|
|
|
|
Home -> Sailboat -> Blocks->57mm Carbo Ratchamatic Blocks
Control loaded lines with ease The 57mm and 75mm Carbo Ratchamatic blocks are adjustable for use in many applications and weather conditions. This load-sensing ratchet block rolls freely in both directions under low loads, then engages the ratchet automatically as loads increase. Great for asymmetrical spinnakers when you need tough holding power and a quick release. Sheave Size: 1-9/16" (40mm). Ball Bearings: Engineered plastic in fitted ball races. Line Diameter: 3/8" .
Part No: 2145
|
|
|
|
Home -> Sailboat -> Traveler, Tracks & Vang -> T Track & Sail Track->Micro-Captive Ball Traveler Cars & Track
Strong, lightweight, solid aluminum, one-piece cars boast stainless steel-wire ball guides that keep the high-strength Torlon balls captive when the car is off the track. Sculpted car bodies reduce weight. Low-profile Micro CB track is fully-saturated Hardkote–anodized for toughness and scratch-resistance. Low-profile, line-shedding endstop absorbs sudden shock loads that can occur during unintentional jibes. Application: Mainsheet cars. Vangs on small dinghies. Controls on small keelboats.
Part No: 2707.1M
|
|
|
|
|
Home -> Sailboat -> Cleats & Stoppers->Offshore Cam-Matic® Cleats
Harken Cam-Matic cleats are legendary for smooth, positive operation when holding and releasing control lines. Light springs allow the cleats to open freely, so the teeth do not have to be sharp and your line lasts longer. Use models with aluminum jaws for high loads or when the line will be drawn through the teeth for adjustment. Models #423 and #365 have carbon fiber jaws for lightweight durability. Cam #150 and #365 require two #10 FHMS. Cam #280 requires two 1/4" FHMS. Each ShWt 0.
Part No: 280
|
|
|
|
|
Home -> Sailboat -> Cleats & Stoppers->Standard Cam Cleats and Accessories
Harken Cam-Matic cleats are legendary for smooth operation when holding and releasing control lines. Three rows of Delrin ball bearings allow the jaws to open and close smoothly under the highest loads. Light springs allow the cleats to open freely, so the teeth do not have to be sharp which means that your line lasts longer. Use models with aluminum jaws for high loads, or when the line will be drawn through the teeth for adjustment.
Part No: 296
|
|
|
|
Home -> Sailboat -> Blocks->Little Hexaratchet® Blocks
Fast trimming in high-load conditions Eight-sided ratchet sheave is machined from solid aluminum for high strength and holding power. Excellent for small boat main, jib, and spinnaker sheets. Sliding button for on/off control. Sheave: Eight-sided Teflon-impregnated Hardkote anodized aluminum. Sheave Size: 2-1/4" (57mm). Line Diameter: 3/8" max. Cheek Material/Finish: Plastic with stainless straps. Shackle/Strap Type: Stamped swivel shackle with three-way head.
Part No: 043
|
|
![2" Cheek, 2,000lb. SWL, 6.0oz. from HARKEN]( "2\" Cheek, 2,000lb. SWL, 6.0oz. from HARKEN")
|
|
Home -> Sailboat -> Blocks->Line/Wire High-Strength Blocks
Lightweight, low-friction blocks with hi-load composite bearings carry wire halyards and control line cascades. Side load balls minimize friction from twisting or unfair leads on 304. 300s have thrust washers. Cheek blocks come with fasteners. Sheave: Teflon impregnated Hardkote anodized aluminum. Sheave Size: 1" (25mm), 1-1/2" (38mm), 2" (51mm). Line Diameter: 1" sheave - 3/32"; 1 1/2 sheave - 1/8"; 2"sheave - 3/16".
Part No: 309
|
|
|
|
|
Home -> Sailboat -> Blocks->16mm AirBlocks®
AirBlocks have a lightweight design and a unique patented bearing system which uses stainless steel balls in a captive, grooved race. Very high working loads in an extremely lightweight block, with the best strength-to-weight ratios around. Sheave: Delrin. Sheave Size: 5/8" (16mm). Ball Bearings: Stainless. Line Diameter: 7/32" max.
Part No: 416
|
|
|
|
Home -> Sailboat -> Winches -> Winch Handles & Holders->Ball-Bearing Winch Handles
Ball bearings allow fast, free cranking. Comfortable grip. Fits most common winches built today. Grip: Ball bearing (Double-grip Model 5252689) . Type: Locking or standard . Material: Aluminum .
Part No: B8AP
|
|
|
|
Home -> Safety -> Man Overboard Gear->Crew Overboard Pole Accessory - Backstay Mount Sleeve
Blue acrylan flag sleeve for the Backstay mount crew overboard pole (Model 317883).
Part No: 202013
|
|
|
|
|
Home -> Sailboat -> Blocks -> Blocks->2.25" Blocks
The original Harken block Used for main and jib sheets on course racing keelboats, scows and dinghies with large mains. Often used for spinnaker halyards and sheets on small offshore boats. Swivel blocks feature a three-way head system with a set screw. Blocks with cams feature adjustable cam arms and reversible cam cleats. Where applicable, blocks use #8 fasteners. Sheave: Delrin. Bearings: Delrin ball bearings. Sheave Size: 2-1/4" (57mm). Line Diameter: 7/16" max.
Part No: 003
|
|
|
|
Home -> Sailboat -> Traveler, Tracks & Vang->Small Boat Captive Ball (CB) Traveler Cars
These lightweight, solid aluminum and compact captive ball (CB) travelers are built to handle very high loads. Captive ball bearings let you roll the cars on and off the track without using a ball loader. Boat Size: Dinghies, multihulls, to small offshore boats. Material: One-piece solid aluminum . Shackle: Pivoting toggle models—fasten control blocks directly to post without needing a shackle. Sheave: Fixed sheave models—mainsheet loads 40° or less from vertical.
Part No: 177
|
|
|
|
|
Home -> Sailboat -> Cleats & Stoppers->Standard Cam Cleats and Accessories
Harken Cam-Matic cleats are legendary for smooth operation when holding and releasing control lines. Three rows of Delrin ball bearings allow the jaws to open and close smoothly under the highest loads. Light springs allow the cleats to open freely, so the teeth do not have to be sharp which means that your line lasts longer. Use models with aluminum jaws for high loads, or when the line will be drawn through the teeth for adjustment.
Part No: 145
|
|
|
|
Home -> Sailboat -> Blocks -> Blocks->40mm Carbo AirBlocks®
From the folks who invented ball bearing blocks, this line of blocks boasts an excellent strength-to-weight ratio. 29mm doubles and triples feature a U-lock to hold the swivel in the front or side position, or allow it to spin freely. Use the 40mm blocks for jib and mainsheet systems on high-performance dinghies, and for high-load control lines on small keelboats. The 57mm blocks have an enormous working range that makes them ideal for main and jib sheets, spinnaker halyards and control lines.
Part No: 2641
|
|
|
|
Home -> Sailboat -> Traveler, Tracks & Vang->Battcar Batten Traveler Systems, System AA Components
For Boats Under 35' Batten Traveler Systems replace conventional sail slugs with ball bearing traveler cars to handle the compression loads from full-length battens. The main becomes easier to hoist and lower, and won’t damage the sail track. Add a lazy jack system, and raising or lowering your mainsail becomes a single person operation. Battcar systems also improve sailing performance, because they do not require the sail to be cut flat, or reduce the size of the roach, as with other systems.
Part No: 3819
|
|
|
|
Home -> Sailboat -> Traveler, Tracks & Vang->Big Boat Track & Accessories
Harken’s Big Boat Traveler Track is available in low-beam and high-beam configurations.
Part No: 3155.2.1M
|
|
|
|
Home -> Sailboat -> Traveler, Tracks & Vang -> Mainsheet Traveler->Midrange Control Blocks
Assemblies easily fasten to the track without additional holes in the boat. Bases and cam arms are machined from a single piece of aluminum for durability and a clean look. End control sheaves are 40mm Carbo blocks with free-running ball bearings to ensure cars adjust easily under load and release instantly in a gust. For angled cleating install the 380 X-treme Angle Fairlead. An integral dead-end terminates control lines. The 1661 or 1638 stand-up toggle holds blocks in a upright position.
Part No: 1633
|
|
|
