Top Sellers
Power Bubbles 12V DC Aerator from MARINE METALS
This system runs on low current as it's dual bellows aerate up to 2L per minute of air. It saturates circulating water with oxygen. Double discharge allows aeration of one or two livewells. Increases flow capacity. Includes 10' of air tubing. Two large airstones allow the pump to be mounted in any protected area. Suitable for fresh or saltwater. Two anti-siphon valves protect pump against water intrusion. Quietly operates with solid-state circuits. Draw: 1/4A at 12V DC.
|
Tachometer/System Check (4"), Johnson/Evinrude outboard, 7000RPM from FARIA INSTRUMENTS
Over 50 years of experience are behind every one of these Faria instrument gauges. They’re designed with an eye for sophistication and a mind for value. Perimeter lighted white dial with stylish blue and black graphics. Polished stainless steel bezel. Contoured black pointer and domed glass lens. All gauges are 12V DC with negative ground and are all internally illuminated unless otherwise noted. Include backclamp, hardware, and installation instructions. Mfr. ’s lifetime limited warranty.
|
Fuel Sending Unit Only - 4-24'' Tank from TELEFLEX
Complete kit includes a reliable dash-mount gauge with a black face and white numerals. The triple patented sending unit has an adjustable float arm and U-channel that fits virtually all tanks from 4"-24" deep. Compatible with 12V DC systems with common or insulated ground.
|
Stern Three-Mile LED Light from ATTWOOD
Energy-efficient three-mile 12" pole anchor/masthead and transom lights. Solid stainless hardware for corrosion resistance and unsurpassed polished appearance. Pole light is direct replacement for Perko 1181DPO CHR used on most Sea Ray boats. Case Material: Stainless steel . Mounting Hardware: Not included . Pole Diameter: 3/4" . Pole Material: Anodized aluminum . Draw: 0. 15A (1. 8W@12V DC) . Volts: 12V DC.
|
Whale Gulper 220 Pump, 12V DC, Draw: 2.4A from WHALE PUMPS
Use this 3. Large 3/4" inlet and outlet valves are cut at 45° angles to minimize flow restriction. Ports rotate to the position you need to facilitate hose connections and it mounts vertically or horizontally—making installation a snap! It can run dry for extended periods without burnout and boasts a large diaphragm that generates up to 13' of lift. Rubber mounting feet reduce noise. Features: Will run dry without damage and pump a mixture of air and water . Large single diaphragm .
|
Panel Mount Thermal Circuit Breaker, 50A from BLUE SEA SYSTEMS
An economical solution for high amperage loads where dependability is required in marine environments. Waterproof and ignition-protected (conforming to SAE J1171) so these circuit breakers are safe for installation aboard gasoline-powered boats. Ideal for branch circuits, windlasses, inverters and watermakers. False-trip free—designed to trip when subjected to a fault current. Available in panel and surface mounts. Interrupt Rating: 3000A at 12V DC. Voltage Compatibility: 42V DC.
|
Dual Warning Light and Buzzer from COLE HERSEE
Works with oil pressure, temperature, halon extinguishers, etc Use with grounded or ungrounded switches For use with Marine Engine Warning Alarm Kit Steel case measures 1-7/8"D x 1"W x 1-11/32"H Fits panels to 13/64" thick 12V DC .
|
500gph 12V Bilge Pump, 1.9A Draw at 12V DC, 3/4" Port, 4"H x 2-3/8"W from RULE INDUSTRIES
An internal computer chip cycles these pumps on every 2. 5 minutes, then quickly shuts them down if no water is detected. Built-in strainer bases snap off to make cleaning easy. Completely submersible, rust-proof, corrosion-proof and ignition-protected. Three-way wiring enables connection to a switch for manual override or indicator light. Small 500gph pump is designed to handle spray and rainwater. Built-In Switch: Yes, cycles every 2. 5 min.
|
800gph Tsunami Bilge Pump, 2.5A @ 12V DC Draw, 3/4" Port, 4-3/8"H x 3-1/2"W from ATTWOOD
Versatile Tsunami pumps feature interchangeable, twist-and-lock cartridges that reduce maintenance time. All wires are caulked and tinned to prevent water wicking. Rugged glass and mineral-filled polymer construction resists chemicals, fuel and detergents and the compact, low-profile design eases installation in tight spaces.
|
12V Macerator Pump, 14A Draw from SHURFLO
Designed specifically for the marine environment with run dry premium impeller technology. 5" male thread to screw directly onto a tank flange. Type: Macerating flexible impeller gpm: 13 Macerates: Yes Self-Prime: 5' Material: Nylon body, nitrile impeller, stainless wear plate Port Sizes: Inlet: 1-1/2" barb and 1-1/2" NPT male; Outlet: 1" hose barb Dimensions: 3-3/8"H x 4-5/8"W x 11"L Innovative blade design ensures problem-free pumping Inlet port has both a 1.
|
Float Switch from SHURFLO
Offered with or without a protective cage, this non-mercury float switch utilizes mechanical contacts for reliable bilge pump activation. Includes 3', tinned wire leads. May be mounted apart from pump or snapped into base plate of Shurflo 380, 500, 700 and 1000gph pumps. 4. 4"L x 3. 6"W x 1. 3"H. For use with 12V and 24V DC pumps. ABS plastic. Two year limited warranty. Activation Method: Float with mechanical contacts .
|
12V Reversible Flo-Master Vane Pump from GROCO
Rigid-vane pumps for pumping water, oil or diesel. Positive-displacement pump is self-priming to 2’. Long-lasting, continuous-duty, ignition-protected motor has ball bearings and a #316 stainless-steel shaft Application: General light to intermittent duty utility pumping . Gallons Per Minute: 6. 5 (oil) . Material: Bronze pumphead, stainless shaft . Port Sizes: Male garden hose or 1/2" female NPT inlet & outlet . Dimensions: 3 3/8"H x 4 3/8"W x 7 1/2"L .
|
Contura Rocker Switch, SPDT On/Off/On from COLE HERSEE
Waterproof switches are rated to IP66 for use on ship decks and with an LED light to indicate when the circuit is on. Several configurations are available for almost any application. Recommended for replacements in waterproof electrical panels with rocker switches to ensure waterproof integrity. Includes both black and gray covers. Both switches and covers are interchangeable with similar switches used as original equipment on many common boat types. Mounting Hole Size: 1. 450" x 0.
|
Deck Mate 25 Boat Anchor Windlass from POWERWINCH
Compact, deck-mounted windlass has power up/free-fall down capabilities and includes a built in light for added convenience. With low power draw and free fall deployment, this anchor winch puts less stress on your battery for longer battery life. Its small footprint takes up less deck space to mount and the spur gear train allows fast retrieval speeds and minimal current draw. Gear feature prevents rope from over running during anchor deployment. Style: Horizontal . Boat Length: Up to 25'' .
|
12V Blaster Washdown Pump, 3.5 GPM from SHURFLO
Blast the grimiest decks clean with one of these durable freshwater/saltwater pumps. Positive-displacement three/four chamber diaphragm design is self-priming up to 6' and can run dry without damage. Include 3/4" and 5/8" garden hose adapters. Pro Blaster features higher capacity and a seamless motor shell for enhanced protection in saltwater environments. Suitable for mounting in wet locations. Include fittings and Blaster spray nozzle. Switch Type: Sealed 45psi pressure switch .
|
|
1A Draw, 0, 12V DC Turbo Fan, Black Bezel, 66"D from HEATER CRAFT
|
|
Home -> Cordage -> Rigging Products->Hi-MOD Failsafe Insulators
The Failsafe Insulator, with features similar to the other Hi-Mod fittings, uses an internal ball socket in the main body which threads onto the connecting stud. The nut is insulated by a Tufnol™ socket, isolating the antenna from the opposite terminal. While the backstay will loosen, the insulating studs will stay attached to the insulator body, allowing the rig to be re-tensioned until a repair can be made.
Part No: CTICC38
|
|
|
|
Home -> Cordage -> Rigging Products->Hi-MOD Failsafe Insulators
The Failsafe Insulator, with features similar to the other Hi-Mod fittings, uses an internal ball socket in the main body which threads onto the connecting stud. The nut is insulated by a Tufnol™ socket, isolating the antenna from the opposite terminal. While the backstay will loosen, the insulating studs will stay attached to the insulator body, allowing the rig to be re-tensioned until a repair can be made.
Part No: CTISS732
|
|
|
|
Home -> Cordage -> Rigging Products->Hi-MOD Failsafe Insulators
The Failsafe Insulator, with features similar to the other Hi-Mod fittings, uses an internal ball socket in the main body which threads onto the connecting stud. The nut is insulated by a Tufnol™ socket, isolating the antenna from the opposite terminal. While the backstay will loosen, the insulating studs will stay attached to the insulator body, allowing the rig to be re-tensioned until a repair can be made.
Part No: CTICC516
|
|
|
|
Home -> Cordage -> Rigging Products->Hi-MOD Failsafe Insulators
The Failsafe Insulator, with features similar to the other Hi-Mod fittings, uses an internal ball socket in the main body which threads onto the connecting stud. The nut is insulated by a Tufnol™ socket, isolating the antenna from the opposite terminal. While the backstay will loosen, the insulating studs will stay attached to the insulator body, allowing the rig to be re-tensioned until a repair can be made.
Part No: CTICC732
|
|
|
|
Hayward Fishing trolling weights can be used with all makes of down-riggers.
Part No: HDRRC-10
|
|
|
|
Hayward Fishing trolling weights can be used with all makes of down-riggers.
Part No: HDRRC-08
|
|
|
|
Hayward Fishing trolling weights can be used with all makes of down-riggers.
Part No: HDRRC-12
|
|
|
|
Hayward Fishing trolling weights can be used with all makes of down-riggers.
Part No: HDRRC-06
|
|
|
|
Home -> Cabin & Galley -> Containers & Storage -> Containers, Boxes, Bins->Communications Caddy
Compact, easy-to-mount organizer keeps communication devices safe and within easy reach. Small enough to fit near the helm of the smallest boat. Holds most handheld VHF and FRS radios. Mounts either on the back or on the bottom using the two large Super Suction cups, included. Mount it where you need it. , stow it away when you don't. Can also be mounted permanently with screws or marine grade adhesive strips. Molded from commercial grade marine resins. 4. 5"H x 3. 5"W x 2.
Part No: 2135-1
|
|
|
|
Home -> Cabin & Galley -> Appliances & Cookware->Suction Drink Holders
Handy, compact drink holder has a suction cup that can be placed on the back, or on the bottom, to keep your favorite beverage in place, on any smooth, flat surface.
Part No: 2150-8
|
|
|
|
Home -> Cabin & Galley -> Appliances & Cookware->Suction Drink Holders
Handy, compact drink holder has a suction cup that can be placed on the back, or on the bottom, to keep your favorite beverage in place, on any smooth, flat surface.
Part No: 2151-1
|
|
|
|
Home -> Cabin & Galley -> Containers & Storage -> Containers, Boxes, Bins->Super Suction Cup Utility Hooks
Suction mounts in cockpit, cabin or flybridge. Super Suction hook holds lines, leaders, towels, wet swim suits or other clothing. Instant organization! .
Part No: 2100-2
|
|
|
|
Home -> Cabin & Galley -> Appliances & Cookware->Suction Drink Holders
Handy, compact drink holder has a suction cup that can be placed on the back, or on the bottom, to keep your favorite beverage in place, on any smooth, flat surface.
Part No: 2151-8
|
|
|
|
Home -> Cabin & Galley -> Containers & Storage->Communications Caddy
Compact, easy-to-mount organizer keeps communication devices safe and within easy reach. Small enough to fit near the helm of the smallest boat. Holds most handheld VHF and FRS radios. Mounts either on the back or on the bottom using the two large Super Suction cups, included. Mount it where you need it. , stow it away when you don't. Can also be mounted permanently with screws or marine grade adhesive strips. Molded from commercial grade marine resins. 4. 5"H x 3. 5"W x 2.
Part No: 2135-8
|
|
|
|
Home -> Cabin & Galley -> Containers & Storage -> Containers, Boxes, Bins->Super Suction Cup Utility Hooks
Suction mounts in cockpit, cabin or flybridge. Super Suction hook holds lines, leaders, towels, wet swim suits or other clothing. Instant organization! .
Part No: 2180-2
|
|
|
|
Hot Tube Accessory for ducted units (included with Model 2835189).
Part No: H509B
|
|
|
|
Home -> Ventilation -> Blowers & Heaters -> Cabin Heaters->Hydronic Heater Kits
Extend your boating season into the crisp months of fall and beyond with an Acu-Heat Hydronic Heating System. They work much like your car's heating system. They include six feet of duct hose per vent. The grilled heaters are perfect for heating cockpit areas or cabins. They mount easily in stairwells or cabin interiors and are often used in tandem with a ducted unit. Kits include 25' of 5/8" heater hose and a universal brass engine fitting and hose barbs for a hassle-free installation.
Part No: 301HC
|
|
|
|
Home -> Ventilation -> Blowers & Heaters->Hydronic Heater Kits
Extend your boating season into the crisp months of fall and beyond with an Acu-Heat Hydronic Heating System. They work much like your car's heating system. They include six feet of duct hose per vent. The grilled heaters are perfect for heating cockpit areas or cabins. They mount easily in stairwells or cabin interiors and are often used in tandem with a ducted unit. Kits include 25' of 5/8" heater hose and a universal brass engine fitting and hose barbs for a hassle-free installation.
Part No: 501HB
|
|
|
|
Home -> Ventilation -> Blowers & Heaters -> Cabin Heaters->Hydronic Heater Kits
Extend your boating season into the crisp months of fall and beyond with an Acu-Heat Hydronic Heating System. They work much like your car's heating system. They include six feet of duct hose per vent. The grilled heaters are perfect for heating cockpit areas or cabins. They mount easily in stairwells or cabin interiors and are often used in tandem with a ducted unit. Kits include 25' of 5/8" heater hose and a universal brass engine fitting and hose barbs for a hassle-free installation.
Part No: 401HC
|
|
|
|
Home -> Ventilation -> Blowers & Heaters -> Cabin Heaters->Hydronic Heater Kits
Extend your boating season into the crisp months of fall and beyond with an Acu-Heat Hydronic Heating System. They work much like your car's heating system. They include six feet of duct hose per vent. The grilled heaters are perfect for heating cockpit areas or cabins. They mount easily in stairwells or cabin interiors and are often used in tandem with a ducted unit. Kits include 25' of 5/8" heater hose and a universal brass engine fitting and hose barbs for a hassle-free installation.
Part No: 203HC
|
|
|
|
Home -> Ventilation -> Air Conditioning & Cooling -> Interior Fans->12V & 24V Turbo Fans
Multi-directional for custom cooling aboard These fans are just right for circulating air on the bridge or inside the steering station because you can point them in almost any direction. Plastic blades are protected by a high-impact plastic guard. 5,000-hour motors. Easy to install, with 4 1/2' cable, included. Capacity: 125cu. ft. /min. . Blade: Soft plastic (3) . Safety Features: Protective grille . Dimensions: 7-5/16"W x 7-5/8"H x 3-3/4"D .
Part No: 003361012
|
|
|
|
Home -> Electrical -> Exterior & Navigation Lighting
Flood the deck. with bright white light! Free-form reflector for close-range homogeneous illumination. White fiber-reinforced plastic housing is UV and impact-resistant, with sealed rear cable-gland entry, prewired with 12' cable. Includes 55W halogen H-3 12V bulb. Glass lens is bonded to reflector, sealed for dust/moisture protection. Suitable for high-vibration environments. Can be rotated through 180°. Upright or pendant mounting.
Part No: 996361131
|
|
|
|
Home -> Ventilation -> Air Conditioning & Cooling -> Interior Fans->12V & 24V Turbo Fans
Multi-directional for custom cooling aboard These fans are just right for circulating air on the bridge or inside the steering station because you can point them in almost any direction. Plastic blades are protected by a high-impact plastic guard. 5,000-hour motors. Easy to install, with 4 1/2' cable, included. Capacity: 125cu. ft. /min. . Blade: Soft plastic (3) . Safety Features: Protective grille . Dimensions: 7-5/16"W x 7-5/8"H x 3-3/4"D .
Part No: 003361002
|
|
|
|
Home -> Ventilation -> Air Conditioning & Cooling -> Interior Fans->12V & 24V Turbo Fans
Multi-directional for custom cooling aboard These fans are just right for circulating air on the bridge or inside the steering station because you can point them in almost any direction. Plastic blades are protected by a high-impact plastic guard. 5,000-hour motors. Easy to install, with 4 1/2' cable, included. Capacity: 125cu. ft. /min. . Blade: Soft plastic (3) . Safety Features: Protective grille . Dimensions: 7-5/16"W x 7-5/8"H x 3-3/4"D .
Part No: 003361022
|
|
|
|
Home -> Electrical -> Exterior & Navigation Lighting -> Navigation Lights->#2984 Navigation Lights for Boats to 65'7" (20 meters)
Very similar to #3562 lights, with larger lamps and size for greater visibility. Bulb hangs to reduce corrosion on socket. For power or sailboats to 65. 6'. Acrylic lens. 25W bulbs in colored lenses produce 2nm visibility, stern light has 2nm visibility, while masthead light has 3nm visibility. Black housing. Case Material: Polycarbonate . Case Dimensions: 4. 24"H x 4. 25"W x 3.
Part No: 002984315
|
|
|
|
Home -> Electrical -> Exterior & Navigation Lighting->#2984 Navigation Lights for Boats to 65'7" (20 meters)
Very similar to #3562 lights, with larger lamps and size for greater visibility. Bulb hangs to reduce corrosion on socket. For power or sailboats to 65. 6'. Acrylic lens. 25W bulbs in colored lenses produce 2nm visibility, stern light has 2nm visibility, while masthead light has 3nm visibility. Black housing. Case Material: Polycarbonate . Case Dimensions: 4. 24"H x 4. 25"W x 3.
Part No: 002984305
|
|
|
|
Home -> Electrical -> Exterior & Navigation Lighting -> Navigation Lights
A dependable source of bright illumination for the cockpit or the fore deck. Doubles as a bright, USCG-approved masthead light for nighttime boating. Vertical surface mount for sailboats and powerboats to 20m (65. 5') long. 3nm visibility. 20W at 12V DC. 7. 5"L x 5. 25"W x 2.
Part No: 998505001
|
|
|
|
Home -> Electrical -> Exterior & Navigation Lighting->Slim Line Round Courtesy Lights
An attractive, energy-efficient, no-maintenance solution for a variety of interior and exterior lighting applications. They consume a fraction of the energy of traditional bulb lamps and run very cool due to their low current draw, providing safer installation and money savings. Shock, impact and vibration-resistant for an ultra-long service life. Each lamp is completely sealed and waterproof (rated IP67). Voltage/Draw: 12V DC/4 milliamps . Fixture Material: UV and impact-resistant plastic .
Part No: 980507351
|
|
|
|
Home -> Electrical -> Interior Lighting -> Led Interior Lights->LED Step Lamp with Polished 316 Stainless-Steel Rim
Stylish, compact and power saving LED step lamps are ideal for interior or exterior installations. Completely sealed and ultra durable, the lamps feature a 30° light down angle and include a polished 316 stainless-steel cap. Multivolt circuit ensures consistent illumination across a range of input voltages from 10–33V DC for low power consumption and an ultra-long service life. Bulb Wattage: 0. 5W . Voltage/Draw: 10-33V DC/0. 5W . Lens Material/Description: Plastic diffusion lens .
Part No: 959680711
|
|
|
|
Home -> Electrical -> Exterior & Navigation Lighting -> Navigation Lights->Navigation Lights - Series 3562
White light mounts on any flat surface for powerboats and sailboats to 12m. Single 10W bulb. Gasketed lens prevents water penetration in rough conditions. For mounting; suspension from a halyard not recommended. 2nm visibility. Black base. Type: All-Around . Case Material: Polycarbonate . Case Dimensions: 2-5/16" dia. x 2-5/8"H . Mounting Hardware: Two RHMS (sold separately) .
Part No: 002492201
|
|
|