Top Sellers
Calibrated Resin Pump Set from MAS EPOXY
For use with 1 quart, 1/2 gallon, 1 gallon, 4 gallon and 5 gallon size containers.
|
Brightside Pre-Kote Primer - Gray, Quart from INTERLUX
Fills minor blemishes and sands easilyOne part primer for use with Brightside or any other one-part topside enamel. Microspheres provide high build and improved sandability. (Replaces Brightside Primer and 279 White Undercoater. ) Application: Brush, roller, airless/conventional spray . Number of Coats Recommended: One or two, depending on surface condition. Drying: Overcoating: 6 to 12 hrs. Drying Time: To touch: 1 to 3 hrs. Coverage: Brush: 112 sq. ft/qt, 450 sq. ft/gal; Spray: 87 sq.
|
Cetol Marine Light - Quart from INTERLUX
Enhances and protects the natural beauty of interior and exterior woodSemi-transparent finish prevents weathering and repels water. just wash wood thoroughly and apply. Three coats are recommended for the first application, followed by annual touchups. Marine Light is more translucent than Marine. If a gloss finish is desired, either may be overcoated with Marine Gloss. Quart. Long-lasting adhesion and protection from UV rays and weathering. Flexible, breathable, translucent finish; Quarts.
|
Micron CSC Antifouling Paint, Red, Quart from INTERLUX
Haul and relaunch without loss of performance The innovative copper-copolymer formula of Micron CSC provides a controlled release of antifouling biocide at the paint surface, which means that the longevity of the coating is related to the amount of paint applied. Can be applied over most paints in good condition. Micron CSC will not lose its effectiveness when hauled out of the water for extended periods of time (such as winter storage). Type: Copolymer . 2% Cuprous Oxide . Additives: None .
|
VC-Offshore - Baltoplate Gray, Gallon from INTERLUX
Used by performance boatsVC Offshore combines superior antifouling performance with a super smooth low friction surface for the performance conscious boater. This high-strength, vinyl antifouling paint, fortified with Teflon® yields a hard, very smooth finish for maximum durability, reduced friction and increased performance. High copper loading fights fouling on performance boats in saltwater. Can be used in fresh, salt and brackish waters. Should not be applied over non-vinyl bottom paints.
|
Chris Craft Stain #573 - Pint from INTERLUX
Chris Craft Stain - Pint Fills grain while staining wood, reducing the number of coats of varnish needed. May also be used on bare mahogany planking before applying primer or sanding surfacer.
|
Adaptor Fitting for Suzuki & Honda Lower Units from WEST MARINE
Metal threaded fitting fits MerCruiser, OMC, Evinrude, Johnson, Honda (70-90hp), Volvo, Force and Gamefisher lower units Fits standard quart plastic bottles. Flexible hose gets to hard-to-reach fill plugs.
|
Fiberglass Cleaner and Wax - Quart from SEAPOWER MARINE PROD
Cleans and waxes in one easy stepCleans, waxes, seals and protects the fiberglass surface. Contains the finest Carnauba waxes and silicones and removes surface oxidation, residue, dock marks, grease and dirt while leaving behind a durable high-gloss finish. Excellent for hand or machine use. Quart.
|
Solid Brass Vertical Action Galley Pump from FYNSPRAY
Vertical plunger pump with a gracefully arched spout. 50 strokes per gallon. 1"diameter tube. Fits 1/2"–5/8" hose. Requires 8 1/2" clearance below counter surface; 9 3/4" above Material: Brass. Capacity: 50 strokes/gal. Dimensions: 9 3/4"H. Cutout Size: 1 1/8". Clearance: 8 1/2".
|
Nauta 9 Gallon Flexible Fuel Tank from IMTRA CORPORATION
Flexible gasoline tanks won't rust, don't rattle, are easy to tie down, easy to carry, and won't scrape your boat. The Nauta 9-Gallon flexible fuel tank features comfortable, molded carrying handles and rugged 840-denier nylon construction. Fitted with a 1 1/2'' pivoting fill and a capped and 1/4'' NPT hose barb. Measures 28 1/2'' x 17 1/2'' x 6 1/2''.
|
Orpine Boat Soap, Quart from ORPIN
Fresh pine scent!Replaces musty mildew odors with a pleasant fresh pine scent. Just one ounce in three gallons of fresh or saltwater will clean a 45'L boat. Biodegradable. Biodegradable.
|
Teak Care - Brightener, Quart from STARBRITE
Clean, brighten and protect your teak in three easy stepsBeautiful teak in three easy steps! Kit contains three pint-sized bottles, one each of Cleaner to remove stains and weathering; Brightener to highlight the natural grain and enhance color; and Oil to seal and protect wood from weather and UV damage. Individual, quart-sized bottles are also available. Cleaner chemically roots out stains, including ugly black mildew stains. Brightener restores teak's lustrous hue.
|
|
|
Fiberglass Boat Cleaner 920 1/2 Gallon from COLLINITE
Removes rust, exhaust, oil, grease, and oxidation stains from fiberglass. Restores the original color quickly without hard rubbing or buffing, leaves a chemically clean surface to which waxes can bond. Use with fiberglass boat wax or heavy-duty paste Fleetwax . Made in U. S. A.
|
Inflatable Boat Antifouling Paint from PETTIT
Water-based, multi-season ablative antifouling paint. For hard- or soft-bottom inflatables. Cleans up with water. Black. Quart. Type: Copolymer Ablative. Recommended Usage: PVC or Hypalon; trailered boats. Biocide: CuOx 41%. Additives: No. Compatibility: With all other antifouling paints in good condition except VC-17. Number of Coats Recommended: Two.
|
|
Quart from INTERLUX, Gallon from INTERLUX, Gal from INTERLUX
|
|
Home -> Paint & Maintenance -> Paint, Varnish & Teak Oil -> Topside Paint
A flattening agent specifically formulated for mixing with Interlux's one-part finishes, Toplac, Brightside, Yacht Enamels and varnishes (Original, Goldspar Clear and Schooner) to produce a variety of gloss, satin or matte effect finishes. For interior and exterior use.
Part No: YMA715/QT
|
|
|
|
Home -> Paint & Maintenance -> Paint, Varnish & Teak Oil->Non-Skid Compound Paint Additive
Use to create nonskid areas on deckThis paint additive is made of very fine polymeric spheres that don’t collect dirt as easily as natural grit. Mix directly into paint and brush or roll on. Ratio is 1/2pt additive to 1qt paint and 1qt to 1gal. Recommended Usage: Turns decks into nonskid surfaces . Application: Brush, roll or broadcast . Compatibility: One and two-part polyurethane, alkyd enamel. Coverage: 1/2 pint per one quart enamel.
Part No: Y2398C/HP
|
|
|
|
Home -> Paint & Maintenance -> Paint, Varnish & Teak Oil->Interdeck® Non-Skid Paint
Provides excellent slip resistance in a variety of colorsInterdeck provides an excellent slip-resistant finish with a tough polyurethane resin that protects decks against everyday wear and tear. Interdeck has a low-sheen finish to reduce sun glare. Available in White, Cream, Beige, Gray and Blue. Formulation: One-part polyurethane nonskid enamel . Application: Brush or roller . Number of Coats Recommended: One or two . Drying Time: At 73°F - To touch: 4 hrs. to 2 days; To walk on: 2 days .
Part No: YJB923/QT
|
|
|
|
Home -> Paint & Maintenance -> Paint, Varnish & Teak Oil -> Oils & Sealers->Premium Teak Oil
Penetrates and protects your teakA special blend of linseed and tung oils. Penetrates even moist wood to create an attractive sheen and easy-to-clean protective finish. Reduces mildew build-up. For all interior and exterior hardwoods. 16. 9oz. Penetrates even moist wood. Special blend of linseed and tung oils. Reduces mildew build up. For all interior and exterior hardwoods. 16.
Part No: YMA016/1L
|
|
|
|
|
Home -> Paint & Maintenance -> Paint, Varnish & Teak Oil->Interdeck® Non-Skid Paint
Provides excellent slip resistance in a variety of colorsInterdeck provides an excellent slip-resistant finish with a tough polyurethane resin that protects decks against everyday wear and tear. Interdeck has a low-sheen finish to reduce sun glare. Available in White, Cream, Beige, Gray and Blue. Formulation: One-part polyurethane nonskid enamel . Application: Brush or roller . Number of Coats Recommended: One or two . Drying Time: At 73°F - To touch: 4 hrs. to 2 days; To walk on: 2 days .
Part No: YJB000/QT
|
|
|
|
Home -> Paint & Maintenance -> Paint, Varnish & Teak Oil->Ultra® Antifouling Paint
The new and improved fast dry formula of Ultra allows you to paint and launch the same day. Ultra provides excellent long-term protection from shell and weed fouling. Ultra is recommended for use wherever the fouling challenge is severe, and can be used in fresh, salt and brackish water on fiberglass, wood and properly primed steel boat hulls and parts. Type: Modified epoxy . Recommended Usage: High fouling areas, year-round immersion, fiberglass, wood hulls . Biocide: 66. 5% Cuprous Oxide.
Part No: Y3669F/1
|
|
|
|
Home -> Paint & Maintenance -> Paint, Varnish & Teak Oil->Brightside One-Part Polyurethane with Teflon
Achieve beautiful results with this easy-to-apply enamel The look of a two-part polyurethane with the application ease of a standard enamel. Teflon additives provide excellent stain and abrasion resistance. UV stabilizers ensure high gloss and color retention. Poly-Flow 4000 resin is self-leveling and provides excellent abrasion resistance and chemical resistance. May be brushed or sprayed on fiberglass, wood, aluminum or steel. At least two coats are required. For use above true waterline.
Part No: Y4248/QT
|
|
|
|
Home -> Paint & Maintenance -> Paint, Varnish & Teak Oil -> Thinners & Solvents->Interthane Thinner 2316 Reducing Solvent
Specific solvents for altering the brushing, rolling or spraying characteristics of specific paints2316 Reducing Solvent is a fast-evaporating solvent that improves sprayability of Perfection and certain epoxy paints. 2333N Reducing Solvent is a slow-evaporating solvent that facilitates brushing application of two-part polyurethanes and certain epoxy paints. To ensure optimum results, carefully read the instructions for the paint you plan to use and select your solvent accordingly.
Part No: Y2316N/1
|
|
|
|
Home -> Paint & Maintenance -> Paint, Varnish & Teak Oil -> Thinners & Solvents->202 Fiberglass Solvent Wash
Essential for use prior to painting bare fiberglass gel coats regardless of their age. A combination of several solvents, some of which evaporate slowly to hold contaminants in suspension so they can be wiped from the surface before the solvent dries. Removes mold release agents, wax, oil and grease.
Part No: Y202/QT
|
|
|
|
Home -> Paint & Maintenance -> Paint, Varnish & Teak Oil -> Thinners & Solvents
A slow drying solvent to ease brushing and facilitate the flow of specified paint coatings. It is recommended in various topside systems for removing sanding residue from fiberglass and wood surfaces.
Part No: Y333/QTCA
|
|
|
|
Home -> Paint & Maintenance -> Paint, Varnish & Teak Oil
Teflon® additive reduces hull friction and drag and increases performance VC17m Extra’s thin film yields a super smooth racing finish that would normally take days of tiresome sanding. Now that’s easy! VC17m Extra contains metallic copper and Biolux Slime blocking technology to protect your boat from zebra mussels, teredo worms, weed, algae and slime fouling. Recommended Usage: Inland lakes, low fouling salt water areas; trailerables, dry-stored, racing boats; fiberglass, wood and steel hulls .
|
|
|
|
Home -> Paint & Maintenance -> Paint, Varnish & Teak Oil->Fiberglass Bottomcoat ACT Bottom Paint with Irgarol
This affordable ablative paint is now formulated with Irgarol to combat slime for even longer-lasting protection in all fouling areas. We recommend at least two coats for first-season application. Type: Ablative Recommended Usage: High to low fouling areas; trailerables, fiberglass, wood, steel hulls Biocide: 42% Cuprous Oxide Additives: Irgarol Number of Coats Recommended: Two Coverage: 113 sq. ft. /qt. , 455 sq. ft/gal Drying Time: Overcoating: 12hrs.
Part No: Y6696B/1
|
|
|
|
Home -> Paint & Maintenance -> Paint, Varnish & Teak Oil->Micron Extra VOC
Micron® Extra VOC uses Biolux® technology, a unique antifouling technology that incorporates organic boosting biocides into a special biocide release system, to block slime and algae growth. It is formulated to meet the strictest VOC regulations in the country while providing excellent antifouling protection Micron Extra VOC is for use below the waterline on fiberglass, wood and properly primed metal boat hulls and parts, in fresh, salt and brackish waters.
Part No: Y5793/1
|
|
|
|
Home -> Paint & Maintenance -> Paint, Varnish & Teak Oil->Perfection Two-Part Polyurethane
Simpler to use then other two-part polyurethane, Perfection has been formulated to enable amateur users to achieve professional quality results with ease on topsides superstructure and decks. Produces a finish with superb color and gloss retention and provides prolonged impact and abrasion protection-even on the highest wear areas. May be brushed, rolled, or sprayed over primed fiberglass, wood, aluminum, or steel. Base Formulation: Two-part linear polyurethane . Drying Time: To touch: 2 hrs.
Part No: YHY999KIT/QT
|
|
|
|
Home -> Paint & Maintenance -> Paint, Varnish & Teak Oil -> Teak Cleaners
Premium Teak Restorer cleans and brightens teak in one step, revealing its natural color and the beauty of its grain. Will not harm varnish, paintwork or aluminum 16.
Part No: YMA015/500
|
|
|
|
Home -> Paint & Maintenance -> Paint, Varnish & Teak Oil->Micron® Extra Antifouling Paint
Micron Extra incorporates Biolux™ along with cuprous oxide to achieve complete protection against shell, weed and slime fouling. This self-polishing process results in the constant, controlled delivery of biocides from freshly exposed paint film surface, and assures consistent, long-lasting performance and maximum efficiency. Micron Extra retains it’s antifouling effectiveness when hauled and can be relaunched without repainting. Multi-season, self-polishing protection with no paint build-up.
Part No: Y5693/1
|
|
|
|
|
Home -> Paint & Maintenance -> Paint, Varnish & Teak Oil->Micron® Extra Antifouling Paint
Micron Extra incorporates Biolux™ along with cuprous oxide to achieve complete protection against shell, weed and slime fouling. This self-polishing process results in the constant, controlled delivery of biocides from freshly exposed paint film surface, and assures consistent, long-lasting performance and maximum efficiency. Micron Extra retains it’s antifouling effectiveness when hauled and can be relaunched without repainting. Multi-season, self-polishing protection with no paint build-up.
Part No: Y5696/1
|
|
|
|
Home -> Paint & Maintenance -> Paint, Varnish & Teak Oil
Dries fast with minimal time to overcoatingExceptionally quick-drying varnish is ideal when fast buildup coats and quick overcoating are necessary. Under most weather conditions, two coats may be applied in one day. Not recommended for use as a finish coat. Quart. Recommended Usage: Fast drying build-up coats. Formulation: Traditional alkyd without UV filters, 48% solids . Additives: Rapid evaporating solvents . Application Method(s): Brush or spray . Drying Time: To touch: 1 to 3 hrs.
Part No: Y100/QT
|
|
|
|
Home -> Paint & Maintenance -> Paint, Varnish & Teak Oil
Self-etching primer promotes adhesion of paint to metal Promotes adhesion of paint to metal. Two-part zinc chromate, vinyl butyral self-etching primer. Must be thinned with Interlux 355 Thinner. Do not apply more than one coat. Two-part kit makes one quart. Primary Usage: Metal conditioner prior to application of other paints . Formulation: Self-etching two-part zinc- chromate vinyl butyral. Applies Over: Clean bare metal. Drying Time: To touch: 30 min; to overcoat: window of 1 to 24 hrs.
Part No: Y353KIT/QT
|
|
|
|
|
Home -> Paint & Maintenance -> Paint, Varnish & Teak Oil -> Thinners & Solvents->202 Fiberglass Solvent Wash
Essential for use prior to painting bare fiberglass gel coats regardless of their age. A combination of several solvents, some of which evaporate slowly to hold contaminants in suspension so they can be wiped from the surface before the solvent dries. Removes mold release agents, wax, oil and grease.
Part No: Y202/1
|
|
|
|
Home -> Paint & Maintenance -> Paint, Varnish & Teak Oil -> Thinners & Solvents->333 Brushing Liquid
Prevents paint from "flashing off" prematurely in hot weatherSlow-drying solvent eases brushing and improves flow with certain paint products. Extends drying time in hot weather.
Part No: Y333/1
|
|
|
|
|
Home -> Paint & Maintenance -> Paint, Varnish & Teak Oil->Brightside One-Part Polyurethane with Teflon
Achieve beautiful results with this easy-to-apply enamel The look of a two-part polyurethane with the application ease of a standard enamel. Teflon additives provide excellent stain and abrasion resistance. UV stabilizers ensure high gloss and color retention. Poly-Flow 4000 resin is self-leveling and provides excellent abrasion resistance and chemical resistance. May be brushed or sprayed on fiberglass, wood, aluminum or steel. At least two coats are required. For use above true waterline.
Part No: Y4990/QT
|
|
|
|
|
Home -> Paint & Maintenance -> Paint, Varnish & Teak Oil->Interdeck® Non-Skid Paint
Provides excellent slip resistance in a variety of colorsInterdeck provides an excellent slip-resistant finish with a tough polyurethane resin that protects decks against everyday wear and tear. Interdeck has a low-sheen finish to reduce sun glare. Available in White, Cream, Beige, Gray and Blue. Formulation: One-part polyurethane nonskid enamel . Application: Brush or roller . Number of Coats Recommended: One or two . Drying Time: At 73°F - To touch: 4 hrs. to 2 days; To walk on: 2 days .
Part No: YJG090/QT
|
|
|
|
Home -> Paint & Maintenance -> Paint, Varnish & Teak Oil -> Topside Paint
Achieve professional-quality results with this simplified two-part painting system Simpler to use then other two-part polyurethanes, Perfection has been formulated to enable “do-it-yourselfers” to achieve professional quality results with ease on topsides, superstructure and decks. It is resistant to a wide range of chemicals, including fuels, mild acids and detergents. May be brushed, rolled, or sprayed over primed fiberglass, wood, aluminum, or steel. Number of Coats Recommended: Two/three .
Part No: YZM914KIT/QT
|
|
|
|
|
Home -> Paint & Maintenance -> Paint, Varnish & Teak Oil->Micron® Extra Antifouling Paint
Micron Extra incorporates Biolux™ along with cuprous oxide to achieve complete protection against shell, weed and slime fouling. This self-polishing process results in the constant, controlled delivery of biocides from freshly exposed paint film surface, and assures consistent, long-lasting performance and maximum efficiency. Micron Extra retains it’s antifouling effectiveness when hauled and can be relaunched without repainting. Multi-season, self-polishing protection with no paint build-up.
Part No: Y5691/QT
|
|
|
|
Home -> Paint & Maintenance -> Paint, Varnish & Teak Oil->Micron CSC Antifouling Paint
Haul and relaunch without loss of performance The innovative copper-copolymer formula of Micron CSC provides a controlled release of antifouling biocide at the paint surface, which means that the longevity of the coating is related to the amount of paint applied. Can be applied over most paints in good condition. Micron CSC will not lose its effectiveness when hauled out of the water for extended periods of time (such as winter storage). Type: Copolymer . 2% Cuprous Oxide . Additives: None .
Part No: Y5583/QT
|
|
|
|
Home -> Paint & Maintenance -> Paint, Varnish & Teak Oil
Apply this sealer to bare wood before paintingSeals wood before application of varnish or enamel. Prevents cracking and plywood checking. Not for use with two-part polyurethane or epoxies. Quart. Recommended Usage: Seals plywood to prevent checking or cracking. Promotes even paint and varnish absorption . Application: Brush, roll, conventional/airless spray . Number of Coats Recommended: Two/three coats, depending on porosity. Drying Time: Overcoating: 8 to 16 hrs. Coverage: 50–100sq.
Part No: Y1026/QT
|
|
|
|
Home -> Paint & Maintenance -> Paint, Varnish & Teak Oil->InterProtect 2000E
Universal above- and below-the-waterline epoxy primerA high build universal above and below waterline epoxy primer for all surfaces. Fills severe cracks and crazing in gelcoat. Adheres well to properly sanded bare metal. Offered in gray, or white, which is excellent as a topside primer. Total Thickness Required: Above waterline: 2 coats; below waterline: 4-5 coats (10 mil minimum) . Drying Time: Overcoating: 3 hrs. to 2 wks @ 60°-80°F. . Coverage: Brush: 60sq. ft/qt. , 240sq.
Part No: Y2002EKIT/1
|
|
|
|
Home -> Paint & Maintenance -> Paint, Varnish & Teak Oil->Brightside® Striping Enamels with Teflon®
Durable coating resists abrasionA high-quality polyurethane finish that has been formulated for application to boottops and accent stripes. Excellent abrasion resistance and durability and ideal for use above the waterline. Contains Teflon® for easy cleaning, reduced waterline staining and added abrasion resistance. 1/2 Pint. Application: Brush, roller, conventional/airless spray. Number of Coats Recommended: Two coats minimum. Drying Time: To touch - 1 to 3 hrs. ; To recoat - 8 to 16 hrs.
Part No: Y4990/HP
|
|
|
|
Home -> Paint & Maintenance -> Paint, Varnish & Teak Oil->Brightside Pre-Kote Primer
Fills minor blemishes and sands easilyOne part primer for use with Brightside or any other one-part topside enamel. Microspheres provide high build and improved sandability. (Replaces Brightside Primer and 279 White Undercoater. ) Application: Brush, roller, airless/conventional spray . Number of Coats Recommended: One or two, depending on surface condition. Drying: Overcoating: 6 to 12 hrs. Drying Time: To touch: 1 to 3 hrs. Coverage: Brush: 112 sq. ft/qt, 450 sq. ft/gal; Spray: 87 sq.
Part No: Y4279/QT
|
|
|
