Teak Plugs - 3/8" from SEAFIT
Use these teak plugs to cover screw heads or fill small holes for a beautiful smooth finish to your installation. Sizes: 1/4" 5/8" 5/16" 3/8" 1/2" 1".

Roller Shaft Cap Nuts Only - 1/2", Pack of 8 from C E SMITH
Roller Size Length Shaft Diameter Shafts and Nuts 4" 5 1/4" 1/2" 4" 5 1/4" 5/8" 5" 6 1/4" 1/2" 5" 6 1/4" 5/8" 8" 9 1/4" 5/8" 10" 11 1/8" 5/8" 11" 12 3/4" 1/2" 12" 13 1/2" 5/8" Shaft Only 18" 19" 5/8" Cap Nuts Only Packs of 8.

Pro Washdown Kit from SHURFLO
Everything you need for tough washdown applications all in one package. Includes the durable 4. 0gpm Pro Blaster washdown pump. Blaster Nozzle. Raw Water Strainer. 3/4" and 5/8" garden hose adapters . UV-protected 25' coiled hose. Coated, seamless motor shell for enhanced protection against wet environments. Manufacturer's Documents Installation Guidelines.

Vent-O-Mate Plastic Cover Only, White from BECKSON MARINE INC
Keep rain out and let air circulate through the cabin with the Vent-O-Mate. Wind moving over the top of the vent creates a vacuum which removes air from your boat at the rate of 350cu. ft. /hr. in a 5-knot breeze. The design keeps rain out, even while open. Cutout: 4". Includes 8" protective white cover. Type: Passive vent . Material: Plastic, stainless . Draw: Non-powered .

12V Blaster Washdown Pump, 3.5 GPM from SHURFLO
Blast the grimiest decks clean with one of these durable freshwater/saltwater pumps. Positive-displacement three/four chamber diaphragm design is self-priming up to 6' and can run dry without damage. Include 3/4" and 5/8" garden hose adapters. Pro Blaster features higher capacity and a seamless motor shell for enhanced protection in saltwater environments. Suitable for mounting in wet locations. Include fittings and Blaster spray nozzle. Switch Type: Sealed 45psi pressure switch .

OEM Replacement Fuel Tanks from MOELLER
The OEM’s (Original Equipment Manufacturer’s) choice in lightweight, non-corroding portable fuel tanks! Includes a universal 1/4" NPT fuel pickup adapter and fulfills all your large and small outboard engine needs. Approved for use in Japan, Australia and New Zealand, Canada, ISO and CSA Certified, UL Listed. 21. 25"L x 14"W x 9.

PE-1 Lexan Mast Pad Eye from FORESPAR
For use on our small poles. 1-3/4"H x 1-1/4" x 5/8"dia. ring. Same ring as supplied with 4-8 and 6-12 poles.

Sanding Discs - 5" Velcro-Backed, 40-Grit, 5 Pack from 3M PRODUCTS
Convenient hook and loop disk attachmentAdapts a 1/4” or 3/8” electric drill so it may be used as a 5” disc sander. Includes three Velcro-backed sanding discs (120-, 80- and 40-grit). Recommended Usage: Sanding fiberglass/gelcoat, paint, wood and metal. Abrasive Material: Aluminum oxide. Backing Type: Hook and loop . Disc Size: 5" disc .

1/4" NPT X 3/8" Brass hose barb from MOELLER
1/4 NPT X 3/8" Brass Hose barbs with male threads.

Hose Adapter, From 1-1/8" to 3/4"-5/8" from RULE INDUSTRIES
#69 is stepped & adapts from 1-1/8" to 3/4" - 5/8" #57 is an elbow & adapts from 1-1/8" to 1" NPT #67 adapts from 1-1/2" to 1-1/8".

304 Stainless-Steel Hose Clamp, 3-1/8" to 4", SAE Size 56 from NORMA
With 9mm-wide (3/8") non-perforated bands, and made of stainless steel, these clamps feature rolled-up edges to prevent hose damage. We recommend two clamps per hose end below the waterline. Hoses are measured by inside diameter, so select a clamp with a maximum opening at least 1/4" larger. Designed to evenly distribute tension force . Work well in many different applications with a high mechanical load .

Pro-Pull Tool Only from NATIONAL PRODUCTS
PRO-PULL Kits let you quickly remove 3- and 4-blade propellers from inboard shafts with a 3/4'' to 1 1/8'' diameter. The tool is made of heat-treated steel and features fine-thread screws for tremendous pulling force with very little effort. Kit also includes: Prop nut wrench, stainless cotter pin, brass prop-shaft key. Brass nylock prop nut, waterproof grease, and a rustproof carrying case.

Off/1/All/2 Battery Switch, 380 Continuous Amps, 850 Intermittent Amps from PERKO
For high-amperage applications like diesel engine starters, large inverters and windlasses. Reinforced polycarbonate body, 1/2"dia. brass terminal connections and an alternator field disconnect. Alt. Field Disc. : Yes . Switch Material: Reinforced Polycarbonate. Terminal Material/Size: Brass 1/2"dia. . Switch Dimensions: 5-1/4"sq. x 3-3/8"H .

13-1/4" x 17" Propeller for Evinrude/Johnson Outboards from MERCURY MARINE
Three-blade aluminum one-piece propellers for Evinrude/Johnson outboards. 8–15hp, 9. 9–15hp 2–stroke 1974 & up, 8/9. 9/15hp 4–stroke 1995 & up: Model 5026695. 20–35hp, 20hp 1984–97, 25/30hp 1984 & up, 35hp 1976 & up: Models 4744207, 8640492. 40–75hp, 40hp 1984 & up, 65hp 1980–85, 48hp 1987–96, 75hp 1975–85, 50hp 1975 & up, Sprint 1986–92, 55hp 1976–79, Formula E 1986–92, 60hp 1980–85: Models 8640484, 4744173, 4744181. 45–75hp large gearcase, OMC Cobra 2. 3–2.

4-Cup 12V Coffee Maker from WARING
Enjoy fresh coffee ashore or afloat with this 4-cup coffee maker that plugs into any 12V outlet. Features include a durable stainless-steel carafe, dripless pour spout, knuckle guard, 30-minute auto shut off, “On” indicator light, and a convenient “Brew Pause” feature that lets you pour a cup of coffee before brewing has finished. Includes coffee scoop and three filters. 10 1/4"H x 5 1/4"W x 7 5/8"D.