Top Sellers
GlobalFix™ iPRO Category II GPS-Enabled EPIRB from ACR ELECTRONICS
The screen shows GPS LAT/LON, operating instructions, usage tips, transmission bursts as well as battery power. Self-testing your beacon is simple and easy to understand, with the iPRO digital display visually guiding you through the self test step by step. The GlobalFix iPRO is also the first EPIRB that offers Dual GPS Technology. Interface your iPRO to your onboard GPS to ensure that your LAT/LON is stored inside so your precise coordinates are transmitted in the first data burst.
|
Deluxe Windshield Washer Kit from AFI
Install your own windshield washer systemFits new or existing AFI Deluxe wiper arm and blade sets, with all the parts to outfit two wiper arms. The kit includes a 3 liter water tank with mounting bracket (8. 5"H x 7"W x 4. 5"D), 12V pump motor and 16' below deck clear tubing, 6' above deck black tubing, clips and sprayer fittings. You supply wiring, an in-line 3A fuse and On-Off momentary switch.
|
12 Volt White Dual Trumpet Mini Air Horn from AFI
White epoxy powder-coated finish over solid brass. Noncorrosive Lexan® diaphragm. 12vDC. . Draws 20 amps max. Includes compressor, air tubing, fittings, and hardware. 5" W x 3-3/4"H x 9-1/2" L.
|
Drop-In Hidden Horn from AFI
Designed for easy installation, this hidden horn mounts from the outside. Compact in size, but capable of 107db loudness. Comes with both black and white snap-on ASA plastic grilles. A weatherproof fabric liner lets sound through, but keeps water out. Prewired for 12V installation. Material: ABS plastic . Loudness dB: 107dB . Design Standards: Meets ABYC specs for boats up to 12 meters . Dimensions: 2"H x 3-3/8"W x 3-1/4"D . Power Requirements: 12 Volts .
|
Teak Winch Pad Cant - 7 1/4" from AFI
Base diameter is 1/2'' larger than top diameter.
|
90" Teak Swim Platform from AFI
A beautiful addition to your ski or fishing boat. Can be cut to fit the curvature of almost any transom. Made from solid teak that's glued, then screwed with countersunk fasteners and plugged.
|
Teak Winch Pad Cant - 6" from AFI
Base diameter is 1/2'' larger than top diameter.
|
TankWatch® 4 Water/Holding Tank Monitor from SEALAND
Reliable micro float switches activate empty, low, mid and full tank levels on the indicator panel. No electrical components contact water or waste. Easy to install using universal flange (sold separately). Includes cap with micro float switches . Indicator panel . Gasket and stainless mounting hardware . Adapts to fit any water or holding tank up to 22" . 45" adjustable probes available by Special Order .
|
Series 250 Exhaust Hose, 2-3/8"ID, 2-3/4"OD, 230psi Burst Pressure from SHIELDS RUBBER
For use in all marine water and wet-exhaust applications. Also for marine wet-exhaust where connection requires great length (greater than 4 x ID) or significant bend. Meets or exceeds standards for certified wet-exhaust hose. Sold by the foot with a maximum continuous length of 10' except where preceded by an asterisk, which indicates a maximum continuous length of 50'. Construction: Black synthetic rubber with wire helix and HD synthetic cord . Temperature Range: –20° to 200° F .
|
Fuel Sending Unit Only - 4-24'' Tank from TELEFLEX
Complete kit includes a reliable dash-mount gauge with a black face and white numerals. The triple patented sending unit has an adjustable float arm and U-channel that fits virtually all tanks from 4"-24" deep. Compatible with 12V DC systems with common or insulated ground.
|
PAR-Max 4 Water-System Pump, 12V from JABSCO
Flow rate: 16. 3 Litres/min (4. 3 gallons/min) Self-priming from dry up to 2. 4m (7. 8ft) Smooth flow. Dry running capability. Soft noise absorbing mounts. Snap-fit port fittings. Corrosion resistant materials. Meets USCG Regulation 183. 410 and ISO 8846 MARINE (ignition protection).
|
Gunnel Guard - 1/2" Round, 1-1/2" Diameter, 20' Length from TAYLOR
These polyester-covered guards will protect your boat from dings and scratches and they won’t rot in the sun or saltwater like cotton guards. Great for use on dinghies and swim platforms, too. Fabric tabs attach easily with screws or nails. Half Round is for flat surfaces; 3/4 Round is for 90° edges. Sold in 10' or 20' lengths or by the foot up to 50'. Material: Polyester fabric/closed-cell foam . Attachment Method: Screws or nails . Shock Absorption Mechanism: Foam padding .
|
P750 Ice Eater, 115V, 25' Cord from POWER HOUSE
The P750 de-ices diameter of approximately 60 feet Prevent damaging ice formation around your boat’s hull with a 3/4 hp energy efficient Ice Eater. Motor is matched with a permanent-split capacitor to ensure quick, high-torque and smooth operation from the single-phase induction motor. Copper, stator motor windings are double-insulated, to guard against water. Internal, hard-faced mechanical seal is itself immersed in dielectric lubricating fluid and protects the motor against water intrusion.
|
|
|
Hatch - Ocean 60 Flat Base from LEWMAR
Well-engineered hatches with CE-certified quality materials and construction. Smoothly styled external hinge enables one-hand operation. Inside handles feature locks that cannot be forced from the outside. Flat base or 1'' flange base (pictured). 3-year warranty. Flat base cutout sizes: Ocean 10 - 10" x 10". Ocean 20 - 7-3/4"W x 13-1/2"L. Ocean 30 - 12-5/8"W x 17-3/4"L. Ocean 40 - 16-3/8" x 16-3/8". Ocean 44 - 17-3/16" x 17-3/16".
|
|
4" from AFI, 20" from AFI, 22" from AFI, 90IN from AFI, Insulated from AFI
|
|
Home -> Engine Systems -> Horns/Wipers/Glove Boxes->XL Plus Trumpet Horns
These very loud horns are built to last due to their sealed sound units. They feature exclusive over-molded motor housings for extra protection and a longer life than other similar horns. Stainless-steel, rust- and corrosion-proof construction of the key components. Includes an international horn signal card and mounting hardware. Sealed sound unit keeps moisture out.
Part No: 10029XLP
|
|
|
|
Home -> Engine Systems -> Horns/Wipers/Glove Boxes
Blades are designed to work only with their counterpart Classic, Deluxe or Standard arms.
Part No: 33017
|
|
|
|
Home -> Anchor & Docking -> Ladders, Ramps & Boat Hooks -> Swim Platforms/Steps->Swim Platform Brackets
A simple way to mount your swim platform. 304 stainless steel brackets, 1. 5"W flat bar stock for the underside of the platform and transom.
Part No: 60996
|
|
|
|
Home -> Paint & Maintenance -> Epoxy & Fiberglass->Teak Winch Pads
Base diameter is 1/2'' larger than top diameter.
Part No: 60465
|
|
|
|
Home -> Cabin & Galley -> Containers & Storage -> Poly Storage Products->Polyethylene Drink or Air Horn Holder
Durable and attractive, these cup holders do double duty as air horn holders - order the insulated models to keep your beverage hot or cold longer! High-density polyethylene.
Part No: 65606
|
|
|
|
Home -> Engine Systems -> Horns/Wipers/Glove Boxes->1.5 Heavy-Duty Wiper Motor
Powers a 22" Deluxe arm and 22" Deluxe blade combination or a 20" Premier arm and 20" Premier blade combination. Fully sealed powdercoated aluminum waterproof base and housing. RF shielded circuitry. Factory pre-set sweep angles of 80° or 110° with easy adjustments of 45° or 60°. 12V electrical system. Two-speed motor. Style: Interior/Exterior . Sweep Direction: Both . Self-Parking: Yes . Case Material: Aluminum . Draw: No-load current 0.
Part No: 71012
|
|
|
|
Home -> Engine Systems -> Horns/Wipers/Glove Boxes->Windshield Wiper Blades, Arms, Motors, and Kits
#32002 and 32003 have 110º adjustable sweep motor. #32000 and 32002 have 2-1/2" shaft length motor and are Windshield Frame Mount. 12 volt, 2 amps. AFI STD Wiper Motor with 11 inch stainless steel standard straight blade (33001) and adjustable (7-1/2 inches to 12 inches) stainless steel arm (33002) . Note: motor is not waterproof and is recommended for interior installations only. AFI Wiper Motors AFI-1000 is waterproof and powers 18" x 18" arm/blade combinations.
Part No: 33022S
|
|
|
|
Home -> Engine Systems -> Horns/Wipers/Glove Boxes->Windshield Wiper Blades, Arms, Motors, and Kits
#32002 and 32003 have 110º adjustable sweep motor. #32000 and 32002 have 2-1/2" shaft length motor and are Windshield Frame Mount. 12 volt, 2 amps. AFI STD Wiper Motor with 11 inch stainless steel standard straight blade (33001) and adjustable (7-1/2 inches to 12 inches) stainless steel arm (33002) . Note: motor is not waterproof and is recommended for interior installations only. AFI Wiper Motors AFI-1000 is waterproof and powers 18" x 18" arm/blade combinations.
Part No: 33002
|
|
|
|
Home -> Cabin & Galley -> Barbecues & Tables->Teak Captain's Chairs
A taller version of the director’s chair, this chair is sized for a bar or counter area. Constructed of solid, oil-finished teak with brass hardware.
Part No: 60048
|
|
|
|
Home -> Engine Systems -> Horns/Wipers/Glove Boxes->Windshield Wiper Blades, Arms, Motors, and Kits
#32002 and 32003 have 110º adjustable sweep motor. #32000 and 32002 have 2-1/2" shaft length motor and are Windshield Frame Mount. 12 volt, 2 amps. AFI STD Wiper Motor with 11 inch stainless steel standard straight blade (33001) and adjustable (7-1/2 inches to 12 inches) stainless steel arm (33002) . Note: motor is not waterproof and is recommended for interior installations only. AFI Wiper Motors AFI-1000 is waterproof and powers 18" x 18" arm/blade combinations.
Part No: 33919
|
|
|
|
Home -> Cabinet & Deck Hardware -> Rail Fittings & Rub Rail -> Hand Rails->Teak Handrails
Handrails are beautiful teak. Handrails are 1 1/16W x 2 1/4"H. 1 loop: 13"L. 2 loop: 23"L. 3 loop: 33"L. 4 loop: 43"L. 5 loop: 53"L.
Part No: 60102
|
|
|
|
Home -> Paint & Maintenance -> Epoxy & Fiberglass->Teak Winch Pads
Base diameter is 1/2'' larger than top diameter.
Part No: 60468
|
|
|
|
Home -> Cabin & Galley -> Containers & Storage
White Poly Accessories White poly accessories from AFI Small binocular rack .
Part No: 65702
|
|
|
|
Home -> Engine Systems -> Horns/Wipers/Glove Boxes -> Horns
Mini Twin Electric Horn Excellent for use in the marine environment. totally seal sound units have type 304 stainless cover, diaphragm and mounting brackets. Material: 304 stainless cover & horn diaphragm. Loudness dB: 106 dB. Approvals: ABYC for boats up to 20 meters. Dimensions: 3"L x 8"W x 1 3/4"H. Power Requirements: 12V. Draw: 3A @ 12V (max. 6A). Fundamental frequency: 490±20/440±20.
Part No: 10001
|
|
|
|
Home -> Anchor & Docking -> Ladders, Ramps & Boat Hooks -> Swim Platforms/Steps->Swim Platform Brackets
A simple way to mount your swim platform. 304 stainless steel brackets, 1. 5"W flat bar stock for the underside of the platform and transom.
Part No: 60995
|
|
|
|
Home -> Cabinet & Deck Hardware -> Rail Fittings & Rub Rail -> Hand Rails->Teak Handrails
Handrails are beautiful teak. Handrails are 1 1/16W x 2 1/4"H. 1 loop: 13"L. 2 loop: 23"L. 3 loop: 33"L. 4 loop: 43"L. 5 loop: 53"L.
Part No: 60108
|
|
|
|
Home -> Paint & Maintenance -> Epoxy & Fiberglass->Teak Winch Pads
Base diameter is 1/2'' larger than top diameter.
Part No: 60469
|
|
|
|
Home -> Cabinet & Deck Hardware -> Rail Fittings & Rub Rail -> Hand Rails->Plastic Handles and Hand Rails
Plastic handles and hand rails. Handles available in black or white PVC coated plastic. Handrails are white polypropolene. Handles are 10" long Handrails are 1 1/16W x 1 3/8"H. 1 loop: 13"L. 2 loop: 23"L. 3 loop: 33"L.
Part No: 74512
|
|
|
|
Home -> Cabinet & Deck Hardware -> Rail Fittings & Rub Rail -> Hand Rails->Teak Handrails
Handrails are beautiful teak. Handrails are 1 1/16W x 2 1/4"H. 1 loop: 13"L. 2 loop: 23"L. 3 loop: 33"L. 4 loop: 43"L. 5 loop: 53"L.
Part No: 60106
|
|
|
|
Home -> Cabin & Galley -> Containers & Storage->Teak Spice Racks
Using only plantation-grown teak, these fine accessories make life aboard more pleasant. Large Spice Rack, 2-3/4H x 23-1/2W x 3-3/4D.
Part No: 62436
|
|
|
|
Home -> Anchor & Docking -> Fenders & Docking -> Dock Steps & Boxes
Using only plantation-grown teak, these fine accessories make life aboard more pleasant.
Part No: 60329
|
|
|
|
Home -> Engine Systems -> Horns/Wipers/Glove Boxes
AFI 34000 MRV Heavy Duty 2-Speed Wiper Motor. It has a factory pre-set sweep of 80° and is adjustable to 45°, 60°, 80° or 110°. Dimensions: 7-5/8"L x 4"W x 2"D. 12 Volt. 2.
Part No: 34000
|
|
|
|
Home -> Engine Systems -> Horns/Wipers/Glove Boxes->Windshield Wiper Blades, Arms, Motors, and Kits
#32002 and 32003 have 110º adjustable sweep motor. #32000 and 32002 have 2-1/2" shaft length motor and are Windshield Frame Mount. 12 volt, 2 amps. AFI STD Wiper Motor with 11 inch stainless steel standard straight blade (33001) and adjustable (7-1/2 inches to 12 inches) stainless steel arm (33002) . Note: motor is not waterproof and is recommended for interior installations only. AFI Wiper Motors AFI-1000 is waterproof and powers 18" x 18" arm/blade combinations.
Part No: 33006A
|
|
|
|
Home -> Cabinet & Deck Hardware -> Rail Fittings & Rub Rail -> Hand Rails->Teak Handrails
Handrails are beautiful teak. Handrails are 1 1/16W x 2 1/4"H. 1 loop: 13"L. 2 loop: 23"L. 3 loop: 33"L. 4 loop: 43"L. 5 loop: 53"L.
Part No: 60110
|
|
|
|
Home -> Cabin & Galley -> Containers & Storage
White Poly Accessories White poly accessories from AFI 7 x 50 Binocular Rack .
Part No: 65704
|
|
|
|
Home -> Cabin & Galley -> Containers & Storage -> Teak Storage Products
Teak Accessories for Cabin & Cockpit Using only plantation-grown teak, these fine accessories make life aboard more pleasant.
Part No: 62512
|
|
|
|
Home -> Cabin & Galley -> Containers & Storage
Teak Accessories for Cabin & Cockpit Using only plantation-grown teak, these fine accessories make life aboard more pleasant.
Part No: 62616
|
|
|
|
Home -> Interior, Flags & Gifts -> Flags & Staffs -> Flag Accessories->Teak Ensign Staffs
Teak Ensign Staffs Our traditional staffs are made of natural teak. which retains its good looks with a minimum of maintenance.
Part No: 60748
|
|
|
|
Home -> Interior, Flags & Gifts -> Flags & Staffs -> Flag Accessories->Teak Ensign Staffs
Teak Ensign Staffs Our traditional staffs are made of natural teak. which retains its good looks with a minimum of maintenance.
Part No: 60750
|
|
|
|
Home -> Engine Systems -> Horns/Wipers/Glove Boxes
Get attention ''right now'' with this powerful 12-volt horn. The stainless steel diaphragm pumps out 124 dB (measured at 1 meter), which makes this our loudest electric horn. The non-corroding ABS case is triple chrome-plated for a shine that will last for years. Comes pre-wired for easy installation. Vibration-dampening pad included. Measures 4 1/4'' Long x 5'' Wide x 6 1/4'' H.
Part No: 10036
|
|
|