Ring Style Car RC-125 from FORESPAR
Separates the up/down and side-to-side motions of the pole to make a bind-free, strong attachment. Shackles are supplied for uphaul/downhaul lines. Stainless steel cheeks, aluminum body and plastic liners. Ring Style Car RC-125 Although a screw-pin stop is supplied, this car is designed to be used with uphaul/downhaul blocks shackled to the bails at each end. Ring ID: 1 5/8". Investment cast stainless steel with plastic liners to reduce friction. Fits UXP and UTR pole end fittings.

5/16" Wire Rope Clamp from SEADOG
Investment Cast 316 Stainless Body / AISI 304 Stainless U-Bolt. Accepts 5/16" wire. 1-5/8" Long. 1-3/8" wide.

PE-1 Lexan Mast Pad Eye from FORESPAR
For use on our small poles. 1-3/4"H x 1-1/4" x 5/8"dia. ring. Same ring as supplied with 4-8 and 6-12 poles.

Anchor Safety Strap from LEWMAR
18" long stainless steel; PVC coated with 4" bolt, nut and snap link Fits 1/4", 5/16" and 3/8" chain.

Selma Splicing Fids Set from SAMSON ROPE
Stainless steel fids make burying line much easier. Work with 1/8"–7/16" single braids or 1/4"–9/16" double braids.

4.5" Stainless-Steel Pop-Up “Neat Cleat” from ATTWOOD
Retractable stainless steel cleats retract to only 1/2" above deck and have direct drainage to the bilge. Corrosion-free. Install easily. Hardware included. Functions: Drains to bilge with drainage receptacle. Requires 3/8" ID tube (not supplied) . Material: Stainless steel . Height: Lowered, 1/2"; Raised, 1-5/8" . Line Size: 1-1/4" line opening . Cutout Size: 7/8" hole saw size. Max.

Thru-Deck Mark V Manual Sanitation Pump from WHALE PUMPS
Reliable, high-capacity pumps for emptying holding tanks, bilges, gray water tanks, etc. Nitrile diaphragms ensure long service life. Offered in Surface-Mount and Universal configurations. Universal design may be surface- or thru-deck mounted—and when mounted thru-deck requires Deck Plate with Ring Kit (Model 182438) to complete installation. 16gpm capacity. Use 1. 5" hose. Type: Manual Diaphragm, bulkhead or thru-deck models . GPM: 14. 75 . Macerates: No .

Barbed Hose Reducer, 1" to 1-1/8" from MARINE EAST
.

Series 250 Exhaust Hose, 7/8"ID, 1-3/16"OD, 565psi Burst Pressure from SHIELDS RUBBER
For use in all marine water and wet-exhaust applications. Also for marine wet-exhaust where connection requires great length (greater than 4 x ID) or significant bend. Meets or exceeds standards for certified wet-exhaust hose. Sold by the foot with a maximum continuous length of 10' except where preceded by an asterisk, which indicates a maximum continuous length of 50'. Construction: Black synthetic rubber with wire helix and HD synthetic cord . Temperature Range: –20° to 200° F .

5" ID, 45° Marine Rubber Exhaust Elbow from SHIELDS RUBBER
Exhaust hose elbows let your wet-exhaust line make tight turns without kinking. They provide excellent tolerance to engine heat, vibration and back pressure. Install over rigid tubing or pipe using the four included stainless T-bolt clamps (two at each end). Not intended for hose-to-hose connections. Lubricate with water or detergent. 250°F max.

Series 250 Exhaust Hose, 2-3/8"ID, 2-3/4"OD, 230psi Burst Pressure from SHIELDS RUBBER
For use in all marine water and wet-exhaust applications. Also for marine wet-exhaust where connection requires great length (greater than 4 x ID) or significant bend. Meets or exceeds standards for certified wet-exhaust hose. Sold by the foot with a maximum continuous length of 10' except where preceded by an asterisk, which indicates a maximum continuous length of 50'. Construction: Black synthetic rubber with wire helix and HD synthetic cord . Temperature Range: –20° to 200° F .

Low-Permeation Fuel Hose, 1/2" ID, 250' Max. Length from SHIELDS RUBBER
Special design NBR tube with an embedded plastic barrier layer limits permeation. The design of this hose provides easy coupling insertion and the NBR/PVC cover is weather and UV resistant. The hose is also polyester reinforced and fire-resistant. Fuel Type: Fuel feed (gasoline up to 85% ethanol blended fuels/diesel/bio-diesel all blends) . Approvals: SAE J1527 Type A1-15 and ISO 7840 Type A1 . Construction: Reinforced with high strength synthetics to resist gasoline/alcohol permeation .

1/4" - 5/16" Anchor connector from WEST MARINE
Cleaner than standard anchor shackles, an anchor connector pulls easily over bow roller. Attaches with an Allen wrench (Included) . High-grade galvanized steel . Safe Working Loads: 1/4" - 5/16" unit: 1,390lbs.

2" ID, 90° Marine Rubber Exhaust Elbow from SHIELDS RUBBER
Exhaust hose elbows let your wet-exhaust line make tight turns without kinking. They provide excellent tolerance to engine heat, vibration and back pressure. Install over rigid tubing or pipe using the four included stainless T-bolt clamps (two at each end). Not intended for hose-to-hose connections. Lubricate with water or detergent. 250°F max.

Series 315 Outboard Fuel Hose - 3/8"ID from SHIELDS RUBBER
Premium-quality fuel hose designed for outboard feed and vent lines. Remains flexible at low temperatures and resists UV sunlight. Silverado 2000 complies with SAE J1527 Type B2 specifications. Should not be used in applications requiring the use of Type B1 fuel feed line.