Top Sellers
Three Steps, 25-1/2"H x 25"W x 35-1/8"D from TAYLOR
Make climbing aboard easier! Durable, UV-resistant, white polyethylene steps have StepSafe non-slip pads for maximum slip protection. Wide 1-1/2" flange makes dock mounting easy. Washable surface cleans easily with soap and water. Handrail and mounting hardware sold separately.
|
Upper Pintle, 1-1/2" Rudder Thickness, 3-3/8" Strap Length, 1" Strap Width, 1-3/4" Pin Length from SCHAEFER
Typical installations use one with a short pin and one with a long pin. Pin diameter: 1/2". All require #10 RHMS.
|
Galley Mixer Faucet, 11-1/2"H x 2"W x 8"L from SHURFLO
All Trinidad Series fixtures are made of marine grade chrome-plated brass and include all necessary installation hardware. Material: Chrome-plated brass . Port Sizes: 1/2" NPT . Clearance: 2-1/4" .
|
|
1-1/2" Single, 1,500lb. SWL, 2.8oz. from HARKEN
Lightweight, low-friction blocks with hi-load composite bearings carry wire halyards and control line cascades. Side load balls minimize friction from twisting or unfair leads on 304. 300s have thrust washers. Cheek blocks come with fasteners. Sheave: Teflon impregnated Hardkote anodized aluminum. Sheave Size: 1" (25mm), 1-1/2" (38mm), 2" (51mm). Line Diameter: 1" sheave - 3/32"; 1 1/2 sheave - 1/8"; 2"sheave - 3/16".
|
Sigmar 170 Bulkhead Heater, BTU Low: 6,000; BTU High: 17,000, 20-1/2"H x 9-1/2"W x 9-1/2"D from SIG MARINE
You can thumb your nose at Jack Frost with a diesel cabin heater. Offered in bulkhead or cabin sole mounting configurations, these heaters feature 304 stainless steel construction, large view windows, easy removal of burners for cleaning (bulkhead mount only) and can be easily adjusted for fuel viscosity. For installation, heaters require the 3" Deck Cap (Model 6867782), Thru-Deck Fitting (Model 6867790), and 3"Dia. Heat Source: Diesel #1, #2, kerosene . Material: Stainless steel .
|
Gudgeon for 1-1/2" Rudder Thickness, 6-9/16" Strap Length, 1" Strap Width, 1/2" Pin Hole from SCHAEFER
These gudgeons are built for 1/2" pins. Use with heavy-duty transom gudgeon (Model 252221) and gudgeon pin (Model 252239). Each requires 1/4" RHMS.
|
One Step, 11-1/2"H x 18-1/2"W x 22-1/4"D from TAYLOR
Make climbing aboard easier! Durable, UV-resistant, white polyethylene steps have StepSafe non-slip pads for maximum slip protection. Wide 1-1/2" flange makes dock mounting easy. Washable surface cleans easily with soap and water. Handrail and mounting hardware sold separately.
|
39.6gal. Flexible Water Tank, 27-1/2" x 55-1/16" from PLASTIMO
Flexible, light and form-fitting, these tanks use a PVC bladder inside a tough, abrasion-resistant nylon outer “envelope. ” Maintenance is easy because the inner bladder can be removed for cleaning and inspection. The bladder is slightly oversized so pressure is exerted on its nylon shell, rather than on the heat-welded seams. 1 1/2" 90° fill and 1/2" straight outlet fittings ready to install. Port Sizes: 1-1/2" 90° fill, 1/2" straight outlet . Vent: No .
|
Lower Pintle, 1-1/2" Rudder Thickness, 7" Strap Length, 1" Strap Width, 2-3/4" Pin Length from SCHAEFER
Typical installations use one with a short pin and one with a long pin. Pin diameter: 1/2". All require #10 RHMS.
|
Salmon, Catfish, Striper Landing Net 26-1/2" x 30-1/2" from ED CUMMINGS
New! Salmon-Catfish-Striper Cradle Net Bow 26-1/2" x 301/2" . Handle 48" .
|
13.2gal. Flexible Water Tank, 27-1/2" x 27-1/2" from PLASTIMO
Flexible, light and form-fitting, these tanks use a PVC bladder inside a tough, abrasion-resistant nylon outer “envelope. ” Maintenance is easy because the inner bladder can be removed for cleaning and inspection. The bladder is slightly oversized so pressure is exerted on its nylon shell, rather than on the heat-welded seams. 1 1/2" 90° fill and 1/2" straight outlet fittings ready to install. Port Sizes: 1-1/2" 90° fill, 1/2" straight outlet . Vent: No .
|
Single Powerclutch, 1/4"–1/2" Line Dia., 1,250lb. MWL from SPINLOCK
Positive one-way locking clutches for easy release and relocking Reliable, lightweight, and powerful enough to handle high loads with outstanding line control. Features improved lever action, soft-feel handles for comfort, excellent line gripping and improved release. Application: Racers up to 27' and cruisers up to 35' . Height: 2-3/4" (69mm) . Length: 5-3/16" (134mm) . Width: Single: 1-1/2" (39mm); Double: 2-9/16" (65mm); Triple: 3-5/8" (91mm) .
|
Flex Trim - Black 1/2" opening from TACO PRODUCTS
For a beautiful finished look on unfinished edges. Just push it on and it's on to stay. Grips on difficult materials, compound curves, etc. Individual corrosion resistant aluminum clips for a permanent grip. Black or White . Sold in 25' lengths. . Available in four sizes:. 5/32" opening x 35/64"H. 1/4" opening x 1/2"H. 3/8" opening x 5/8"H.
|
Flex Trim - White 1/2" opening from TACO PRODUCTS
For a beautiful finished look on unfinished edges. Just push it on and it's on to stay. Grips on difficult materials, compound curves, etc. Individual corrosion resistant aluminum clips for a permanent grip. Black or White . Sold in 25' lengths. . Available in four sizes:. 5/32" opening x 35/64"H. 1/4" opening x 1/2"H. 3/8" opening x 5/8"H.
|
Double Powerclutch, 1/4"–1/2" Line Dia., 1,250lb. MWL from SPINLOCK
Positive one-way locking clutches for easy release and relocking Reliable, lightweight, and powerful enough to handle high loads with outstanding line control. Features improved lever action, soft-feel handles for comfort, excellent line gripping and improved release. Application: Racers up to 27' and cruisers up to 35' . Height: 2-3/4" (69mm) . Length: 5-3/16" (134mm) . Width: Single: 1-1/2" (39mm); Double: 2-9/16" (65mm); Triple: 3-5/8" (91mm) .
|
|
1, 1 1, 2'' from SEADOG, 2" from JABSCO, 8'' from SEADOG, 000 from NIMA
|
This site contains about 40,764 documents.
|
|
View by:
Title
|
Category
|
Manufacturer
|
Part No
|
Price
|
|
Page:
1
100
200
300
400
500
600
700
800
900
1,080
1,090
1,100
1,110
1,120
1,130
1,140
1,150
1,160
1,171
1,172
1,173
1,174
1,175
1,176
1,177
1,178
1,179
1,180
1,181
1,182
1,183
1,184
1,185
1,186
1,187
1,188
1,189
1,190
1,191
1,192
1,193
1,194
1,195
1,196
1,197
1,198
1,199
1,200
1,210
1,220
1,230
1,240
1,250
1,260
1,270
1,280
1,300
1,359
|
|
|
Paint & Maintenance -> Zinc Anodes -> Outboard/Outdrive Anodes->Mercury Alumnium Anode Bolt
All Zinc anodes conform to Mil-A18001. All Mercury anodes conform to Mil-A-24779.
Part No: 55989-A
|
|
|
Navigation -> Charts & Chart Catalogs->Fishing & Diving Waterproof Charts
Special editions for fishing and diving! These charts have all of the great quality features you've come to expect from Waterproof Charts! They cover the fishing areas in complete detail, and pinpoint dozens of fishing areas and the fish caught in each area.
Part No: 55F
|
|
|
Plumbing -> Bilge Pumps
Heavy duty construction for both commercial and pleasure boat use; known for trouble free operation and reliability. 1-1/2" (38mm) discharge outlet. Flow Rate: 3700 gph 14010 lph . Port Type: 1-1/2" (38mm) Hose barb . Voltage: 12 Vdc . Amp Draw: 15. 5 amp . Fuse Size: 25 amp . Height: 8-1/4 inches 209. 5 mm . Width: 4-7/8 inches 124 mm .
Part No: 55S
|
|
|
Navigation -> Charts & Chart Catalogs -> North & Central America->Maryland, Delaware, & New Jersey Region
Printed on both sides, these charts save you money! And because they are printed on synthetic paper, they are impervious to water, fresh or salt, so you can use them on deck in rain or spray. Convenient size—25"H x 38"W—makes them easy to fold and store. Used by the Coast Guard and the Navy, these charts are updated regularly and include Loran and GPS coordinates on most charts. Special editions for fishing and diving . Exact positions for wrecks and reefs .
Part No: 56
|
![Dia 1/4", Thread 20, L-1", Pack of 100 from FASCO FASTENERS](http://images.westmarine.com/thumb/535906_t.jpg "Dia 1/4", Thread 20, L-1", Pack of 100 from FASCO FASTENERS")
|
|
Fasteners -> Mechanical Fasteners -> Retail Packs & Kits->Machine Bolts, Hex Head, Bulk Packs
Type 18-8 stainless steel.
Part No: 56
|
|
|
Anchor & Docking -> Ladders, Ramps & Boat Hooks
Kit contains two eye-bolts, two extenders, four fiddle screws and two 20" inflatable buoys. This allows your dog to walk from deep water onto your boat.
Part No: 560
|
|
|
These rocker switches come in several different configurations for panel mounting. Available in illuminated and non-illuminated models, they feature non-glare black matte plastic housings, bezel and actuator, brass screw or blade terminals, and gasket-sealed housings. Snap-in mounting in panels from 0. 093" (2. 36mm) to 0. 187" (4.
Part No: 56027-01-BP
|
|
|
Defense Mapping Agency charts (now known as National Imagery and Mapping Agency or NIMA charts) are U. S. government charts of waters other than the territories and possessions of the U. S. (see NOAA charts for coverage of U. S. territories).
Part No: 56031
|
|
|
Interior, Flags & Gifts -> Knives & Pocket Tools -> Multi-Purpose Tools
Multi-purpose pocket tool with a Cellidor handle and the following features: large blade . small blade . Phillips screwdriver . can opener with . small screwdriver . cap lifter with . screwdriver . wire stripper . reamer, punch . key ring, stainless . tweezers .
Part No: 56057
|
|
|
Anchor & Docking -> Fenders & Docking
At last—a fender specially sized to protect your transom or swim step! A 3/4"dia. tube allows a securing line to be passed through. Fits swim platforms up to 4" thick. Unique shape also fits sailboat transoms. 10"W x 22"L . White.
Part No: 56090
|
![Dia #12, Length 1-1/4", Pack of 50 from FASCO FASTENERS](http://images.westmarine.com/thumb/123143_t.jpg "Dia #12, Length 1-1/4", Pack of 50 from FASCO FASTENERS")
|
|
Fasteners -> Mechanical Fasteners->Tapping Screws - Phillips Pan Head - Bulk
Type 18-8 stainless steel.
Part No: 560A
|
|
|
Fishing -> Reels -> Spinning Reels->Slammer Live Liner Reels
Trophy-hunting? Use a Slammer reelFor the serious angler targeting trophy fish. Their over-sized, sealed drag located under the spool ensures consistent and smooth performance. These Live Liner models have all the Slammer features plus the benefit of an automatic Live Liner drag. They're the perfect reels for anglers who prefer the ease of a spinning reel, but the practicality of a conventional reel. Live Liner drag is adjustable. Fish various sized baits.
Part No: 560L
|
|
|
Cordage -> Anchor Line & Dock Line -> Chafe Gear and Snubbers->Leather Chafe Guards
The traditional chafe protection that many still prefer. If sleeve is to be placed over tail of eye splice, order one size larger than line diameter. Includes: 2 pre-punched 10"L leather sleeves . Waxed Twine .
Part No: 561010-1
|
|
|
|
Cordage -> Anchor Line & Dock Line -> Chafe Gear and Snubbers->Leather Chafe Guards
The traditional chafe protection that many still prefer. If sleeve is to be placed over tail of eye splice, order one size larger than line diameter. Includes: 2 pre-punched 10"L leather sleeves . Waxed Twine .
Part No: 561012-1
|
|
|
|
Cordage -> Anchor Line & Dock Line -> Chafe Gear and Snubbers->Leather Chafe Guards
The traditional chafe protection that many still prefer. If sleeve is to be placed over tail of eye splice, order one size larger than line diameter. Includes: 2 pre-punched 10"L leather sleeves . Waxed Twine .
Part No: 561016-1
|
|
|
|
Cordage -> Anchor Line & Dock Line -> Chafe Gear and Snubbers->Leather Chafe Guards
The traditional chafe protection that many still prefer. If sleeve is to be placed over tail of eye splice, order one size larger than line diameter. Includes: 2 pre-punched 10"L leather sleeves . Waxed Twine .
Part No: 561019-1
|
|
|
|
Defense Mapping Agency charts (now known as National Imagery and Mapping Agency or NIMA charts) are U. S. government charts of waters other than the territories and possessions of the U. S. (see NOAA charts for coverage of U. S. territories).
Part No: 56120
|
|
|
Fasteners -> Mechanical Fasteners->Cap Nuts
Type 18-8 stainless steel.
Part No: 5614
|
|
|
|
Fasteners -> Mechanical Fasteners->Cap Nuts
Type 18-8 stainless steel.
Part No: 5615A
|
|
|
Plumbing -> General Purpose Pumps -> General Purp Pump Parts->Impellers
Impeller Kit 2x7/8|Impeller Kit 2x7/8.
Part No: 5616-0001-P
|
|
|
|
Defense Mapping Agency charts (now known as National Imagery and Mapping Agency or NIMA charts) are U. S. government charts of waters other than the territories and possessions of the U. S. (see NOAA charts for coverage of U. S. territories).
Part No: 56160
|
|
|
|
Fasteners -> Mechanical Fasteners->Cap Nuts
Type 18-8 stainless steel.
Part No: 5616A
|
|
|
|
Fasteners -> Mechanical Fasteners->Cap Nuts
Type 18-8 stainless steel.
Part No: 5618C
|
|
|
|
Fasteners -> Mechanical Fasteners->Tapping Screws - Phillips Pan Head - Bulk
Type 18-8 stainless steel.
Part No: 561A
|
|
|
Engine Systems -> Engine Parts->NGK Spark Plugs
.
Part No: 5626
|
|
|
Engine Systems -> Propellers & Drive Trains->Thrust Hub Prop Spacers
Fits Mercruiser 1 (1982 and older).
Part No: 56292Q04
|
|
|
|
Fasteners -> Mechanical Fasteners->Tapping Screws - Phillips Pan Head - Bulk
Type 18-8 stainless steel.
Part No: 562A
|
|
|
|
Fasteners -> Mechanical Fasteners->Tapping Screws - Phillips Pan Head - Bulk
Type 18-8 stainless steel.
Part No: 563
|
|
|
|
These rocker switches come in several different configurations for panel mounting. Available in illuminated and non-illuminated models, they feature non-glare black matte plastic housings, bezel and actuator, brass screw or blade terminals, and gasket-sealed housings. Snap-in mounting in panels from 0. 093" (2. 36mm) to 0. 187" (4.
Part No: 56327-01-BP
|
|
|
Engine Systems -> Engine Instruments->Pitot Tubing by the Foot
Small vinyl tubing for powerboat speedometers.
Part No: 56353P
|
|
![Salmon, Catfish, Striper Landing Net 26-1/2" x 30-1/2" from ED CUMMINGS](http://images.westmarine.com/thumb/2701407_t.gif "Salmon, Catfish, Striper Landing Net 26-1/2" x 30-1/2" from ED CUMMINGS")
