Auxiliary Steering Kits for Trolling Motors - Zinc Rod from MARINETECH PRODUCTS
Steer your trolling motor with your boat's main steering wheel. These connector rods attach the trolling motor directly to the main engine—when the big one moves, the little one moves along with it. Kits come complete with two quick disconnect ball joint assemblies which make taking it off when you don't need it easy. Connect rod length is 24", cut it to size for a perfect fit. Use the drive bracket for motors that have SeaStar or Teleflex steering.

Johnson/Evinrude, motor only, for 2-wire systems, 90–225hp (1991–1999) from SIERRA
Tilt/Trim Motors, Outboard Applications.

Roller Shaft Cap Nuts Only - 1/2", Pack of 8 from C E SMITH
Roller Size Length Shaft Diameter Shafts and Nuts 4" 5 1/4" 1/2" 4" 5 1/4" 5/8" 5" 6 1/4" 1/2" 5" 6 1/4" 5/8" 8" 9 1/4" 5/8" 10" 11 1/8" 5/8" 11" 12 3/4" 1/2" 12" 13 1/2" 5/8" Shaft Only 18" 19" 5/8" Cap Nuts Only Packs of 8.

Bilge Pro Replacement Motor Cartridge for 500gph Pumps from JOHNSON PUMP
In the event of a problem, replacing your cartridge bilge pump motor is easy— provided you keep one of these on hand. Just pop out the old cartridge and pop in the new. Fit Johnson, West Marine Bilge Pro and Mayfair cartridge-style bilge and livewell pumps.

Motor Mate Lifting Davit from FORESPAR
The unit stores in its own 31" (787. Comes with tackle and will lift anything from the dinghy to the cockpit (or vice-versa) up to 100 lbs. Great for the dinghy motor, but also good for scuba tanks, ice, duffel bags, groceries, etc. The Motor Mate uses a Railfast® mounted ring on the rail and a "toe" on the cockpit coaming directly under the rail. Lightweight, portable, compact . Ideal for lifting outboard motors, sea bags, scuba gear . Lifting capacity: 100 lbs.

Stern Rail Outboard Motor Mount for 1" Railing from EDSON CORPORATION
Convenient cleat and side handles allow you to tie the motor and lock it safely on board. The non-corroding polished 316 stainless bracket with nonskid pad, bolted to the UV stable poly backing board always looks shipshape. no more varnishing. Comes complete with hardware to attach to any standard 1'' (2. 5cm) stainless rail. Warning: Be sure the engine is securely tied onto the backing board and the engine mounts are tightened whenever the engine is stored on Edson's Outboard Motor Mount.

Stern Rail Outboard Motor Mount - Aluminum for 1-1/4" Railings from EDSON CORPORATION
Built to hold motors up to 15 hp or 100 lbs/45 kg. Convenient cleat and side handles allow you to tie the motor and lock it safely on board. The non-corroding polished 316 stainless bracket with non-skid pad, bolted to the UV stable poly backing board always looks ship-shape… no more varnishing. Bottom cleat comes unattached so that it will fit any rail spacing. Note: 1-1/4” rail version comes complete with anodized aluminum bracket, stainless cleat and stainless U-bolt for 1-1/4” railing.

OSCO GASKET FOR 274147 from OSCO MOTORS CORP.
Fits Osco Motors # 8125 manifold .

500gph 12V Bilge Pump, 3/4" Port, 1.9A Draw, 2.5A Fuse, 3-1/2"H x 2-3/8"W from RULE INDUSTRIES
Tough and reliable at a value price Great performance at a value price, Rule submersible pumps are the first choice for many boat manufacturers. Their motors feature stainless-steel shafts, water cooling and a vibration-free centrifugal impeller that won’t burn out if run dry. Strainer bases can easily be snapped off for cleaning. Each pump requires a panel switch for manual operation or a float switch for automatic operation. Select from 12V, 24V and 32V models. Can run dry without damage.

500 RC Windlass, 600lb. Max. Pull, Boat Length 35', 1/4"HT Chain, 1/2" Rope Rode Size, 62'–Chain; 45'–Rope Speed Up/Min., 60' Speed Down/Min., 60A–75A @12V Draw from MAXWELL
These low-profile windlasses feature a patented tension system that maintains resistance required to feed chain/rope rode into the locker instead of jamming it in the windlass. Designed for easy installation, the motor can be oriented in any of 12 positions below decks. Two pieces bolt together quickly. Gasketed, watertight base. For decks to 2 3/4" thick. Capstan models and extra-long shafts for thick decks are available by Special Order. Style: Vertical . Rode Type: Rope/chain .

Gulf Islands Cruising Guide from ROBERT HALE
covers the waterways from Juan de Fuca Strait to Comox including Hornby and Denman and Lasqueti Islands.

12V Reversible Flo-Master Vane Pump from GROCO
Rigid-vane pumps for pumping water, oil or diesel. Positive-displacement pump is self-priming to 2’. Long-lasting, continuous-duty, ignition-protected motor has ball bearings and a #316 stainless-steel shaft Application: General light to intermittent duty utility pumping . Gallons Per Minute: 6. 5 (oil) . Material: Bronze pumphead, stainless shaft . Port Sizes: Male garden hose or 1/2" female NPT inlet & outlet . Dimensions: 3 3/8"H x 4 3/8"W x 7 1/2"L .

Offset Threaded Shaft Cam Bar from PERKO
Spare offset threaded shaft cam bar for your surface mount lock & latch set.

Transom Adapter for Bracket from FULTON
Lets you remove your outboard bracket and outboard for security and less stress and fatigue on the transom while trailering. A locking device helps theft-proof motor and bracket. Heavy-duty marine-grade aluminum with stainless steel mounting bolts supplied. For Adjustable Brackets above (Models 380321 & 389866).

Walker Bay 10, 9'8" Length, 4'9" Beam, 126lb., 449lb. Capacity (up to 3 people) from WALKER BAY BOATS
Bolt in the seats, break out the oars (or optional sail kit or motor) and you’re ready to cast off. Boats include exclusive Hydro-Curve Oars. Application: Rowing, motoring or sailing . Hull Material: High Impact Polypropylene . Construction: High-pressure injection molded . Hull Shape: Round bottom lapstrake-style . Standard Hardware: Oars, oar locks, seats, stainless bow eye, Wheel in the Keel™ . Available Accessories: Sail kits, RID kits, Bimini boat cover . Warranty: 10 years limited.