Aluminum Transom Support Master Mounting Kit from TELEFLEX
Universal mount for most outboard engine steering applications. This kit includes the Teleflex Outboard Clamp Block, Support Tube, and the Clevis Kit.

SeaStar Helm Seal Kit from TELEFLEX
Replacement shaft seal kit HS5176 fits various post-1990 SeaStar 1. 4, 1. 7 (I), 2. 0, 2. 4 (II), SeaStar Pro and SeaStar helms.

BayStar Helm Seal Kits from TELEFLEX
Replacement front seal kits for both front and rear mount helms. HS5147 fits BayStar front mount and SportTilt helms . Contains 3 screws, shaft seal and o-ring seal.

Outboard Cylinder Hydraulic Seal Kit from TELEFLEX
A replacement hydraulic seal kit for Seastar outboard front-mount hydraulic steering cylinders.

Auxiliary Steering Kits for Trolling Motors - Zinc Rod from MARINETECH PRODUCTS
Steer your trolling motor with your boat's main steering wheel. These connector rods attach the trolling motor directly to the main engine—when the big one moves, the little one moves along with it. Kits come complete with two quick disconnect ball joint assemblies which make taking it off when you don't need it easy. Connect rod length is 24", cut it to size for a perfect fit. Use the drive bracket for motors that have SeaStar or Teleflex steering.

Big-T Rotary Helm from TELEFLEX
Die-cast gears and added shaft support help it hold up to tough use. For single or twin station powerboats up to 34'. Boat Type: Inboards and power-assisted sterndrives, up to 34' . Steering Type: Rotary . Dimensions: 6-13/16"D behind dash front x 6-3/8"W x 5-1/16"H . Steering Wheel: Up to 20". Not included . Steering Wheel Shaft: 3/4" tapered . Cable Type: QC II SSC61XX or SSC72XX . Mounting Hardware: Requires bezel kit sold separately .

Fuel Sending Unit Only - 4-24'' Tank from TELEFLEX
Complete kit includes a reliable dash-mount gauge with a black face and white numerals. The triple patented sending unit has an adjustable float arm and U-channel that fits virtually all tanks from 4"-24" deep. Compatible with 12V DC systems with common or insulated ground.

IN-Series Dual Station Kit/ 30 Series from TELEFLEX
S-controls In-Series Dual Station Kit.

3300 Pivot Kit, Brass from TELEFLEX
3300 Pivot Kit, Brass.

Micro Carbo-Cam Cleat Kit with 423 Cam, 329 Fairlead from HARKEN
Micro Cam-Matic cleats are legendary for smooth, positive operation when holding and releasing control lines. Mounted aft of the cam, fairleads allow you to engage and release a line up to 45° on either side of the cam. Mounted ahead of the cam, fairleads allow moving lines, such as small catamaran traveler controls, to lead properly. Cam kits include: Cam-Matic® cam cleat: Pawls open/close easily on ball bearings . Large diameter low-friction guides with stainless steel tubes protect lines .

Service Kit for 30124-0000 Bilge Pump, 8 GPM from JABSCO
Kit includes Connecting rod. Diaphragm. Ppulsation dampener. Valve plate. Valve set (inlet and outlet) .

Service Kit for Gusher MKIII, Cabinet Mount Foot Pump. from WHALE PUMPS
Parts service and repair kits for Whale Water Systems Units.

Flo-Torq II Hub Kit, Mercury 225 EFI fourstroke outboards; Yamaha 225hp 4-stroke outboards, Prop Series B from MERCURY MARINE
Change props faster, cheaper, with Quicksilver's modular hubFlo TorQ II modular propellers let you easily switch props, change pitch, change from aluminum to stainless, or replace a bent propeller. They're a direct replacement for the Michigan XHS hub kits. When large underwater obstruction are encountered, the Delrin sleeve of the Flo-Torq II System is designed to "break away" following impact, ensuring that damage to the engine, engine drive and propeller is kept to a minimum.

Furler Kit for Boat Length to 16', 500lb. SWL, 1/8" Max. Wire dia., 1/4" Pin dia., 2-1/2" Pin-to-Pin, 5/32" Furling Line dia. from HARKEN
Furl or set your jib from your cockpit Harken small boat furlers allow the sail to be set and furled from the cockpit, a critical convenience in many racing dinghies and trailerable sailboats. Constructed of Hardkote anodized Teflon-impregnated aluminum, they feature multiple stacked races of Delrin or Torlon ball bearings for smooth rotation under load. The jib’s luff wire must be properly seized to the sail, since it carries most of the headstay load. 434 furler for dinghies under 16ft. (4.

Impeller Kit from SHURFLO
Dual Head Pump Service Kits for Models 7013378 and 7013386.