Top Sellers
|
|
Stainless-Steel “S” Hook, 3/16" Wire Dia., 5/8" Inside Width from SEAFIT
Stainless Steel "S" Hooks. Polished Stainless Steel Made in the U. S. A.
|
1/4" Dia. Stamped Halyard Shackle, 1,000SWL from SCHAEFER
Stamped Halyard Shackles haveflared heads with cross pin retainer for attachment to rope. Captive design prevents accidental opening Quick release pin #93-42 - 1/4" Shackle Pin dia. , 1/2" Inside Width, 1,000 SWL #93-45 - 5/16" Shackle Pin dia.
|
Spanner Wrench from GROCO
For use with Groco strainers and deck plates with holes up to 7" apart. Cast bronze with 1/4" dia. stainless steel pins on one side and 5/16" pins on the other. Made in USA.
|
Furler Kit for Boat Length to 16', 500lb. SWL, 1/8" Max. Wire dia., 1/4" Pin dia., 2-1/2" Pin-to-Pin, 5/32" Furling Line dia. from HARKEN
Furl or set your jib from your cockpit Harken small boat furlers allow the sail to be set and furled from the cockpit, a critical convenience in many racing dinghies and trailerable sailboats. Constructed of Hardkote anodized Teflon-impregnated aluminum, they feature multiple stacked races of Delrin or Torlon ball bearings for smooth rotation under load. The jib’s luff wire must be properly seized to the sail, since it carries most of the headstay load. 434 furler for dinghies under 16ft. (4.
|
Large Dinghy Snatch Block, 9/16" Line Dia., 40mm Sheave Dia., 1300 SWL from HOLT ALLEN
Glass-filled nylon cheeks with 316 stainless straps increase working efficiency more than 50% with minimal weight increase. Stainless ball bearings in a polypropylene cassette. For spinnaker sheet, jib sheet turning blocks, etc. Cheek Material/Finish: Glass filled nylon. Ball Bearing: Stainless ball bearings. Opening: Hinged cheek/axle.
|
|
|
Triple, 1/2" - 9/16" Line Dia., 59.6oz from LEWMAR
Allows controlled release under loadThe award winning D2 Rope Clutch, built for big boat applications, allows for an easy and controlled release even at full holding power. Instead of just jamming the rope, the D2 clutch's Domino Cluster mechanism has a longer holding pattern for better grip and less rope wear. Fits line sizes from 5/16" (8mm) to 9/16" (14mm). Application: High load applications on boats to 55', low load and control lines on larger boats . Safe Working Load: 2650lb.
|
Swivel Anchor Connector, 5/16"–7/16" Chain, 2750lb. SWL from WEST MARINE
18-8 stainless swivel connectors prevent snagging at the anchor/chain connection, slide easily over anchor rollers and prevent the chain from becoming twisted while the anchor is set. Attach with a single set screw (using the Allen wrench included).
|
|
|
|
|
Replacement Delrin Roller, 3" Dia., 3-3/8" Width from LEWMAR
Anchor rollers make dropping and weighing anchor easier on you and your boat. They help reduce chafe, prevent scratches and dings to your boat’s finish and provide a secure place to store your anchor when used in conjunction with an optional chain stopper or tensioner. We stock rollers to fit the most common combinations of anchor, mounting style and boat. Installation note: overhanging anchor rollers should be supported along at least 2/3 of their length. Easily installed using common tools.
|
3/16" Stock Dia. U-Bolt, 1-3/8” Thread Length, 1-3/16" Hole Spacing, 1" Eye Dia. from SEAFIT
Stainless steel U-Bolts have metric threads. The top plate is held in place by small ears that are forged into the U-bolt. Includes matching backing plate. ShWt .
|
Replacement Delrin Roller, 2-1/2" Dia., 1-3/4 Width from LEWMAR
Anchor rollers make dropping and weighing anchor easier on you and your boat. They help reduce chafe, prevent scratches and dings to your boat’s finish and provide a secure place to store your anchor when used in conjunction with an optional chain stopper or tensioner. We stock rollers to fit the most common combinations of anchor, mounting style and boat. Installation note: overhanging anchor rollers should be supported along at least 2/3 of their length. Easily installed using common tools.
|
Series 40 Ratchet Block, Single/Cleat, 385lb. SWL, 3.4oz. from RONSTAN
Practical Sailor's Ratchet Block Click-Off rated Ronstan's Orbit block "Overall, the most impressive with its grip, versatility, and lightweight design. " The newest addition to Ronstan’s Orbit range of super lightweight, fiber-reinforced blocks. Ideal for sheet applications on dinghies up to 16' and control line applications for small keel boats. There are two styles of Series 40 ratchet blocks. Many of the top Grand Prix Laser sailors are switching to Orbit blocks.
|
|
from RONSTAN, 8oz, 16" Pin Dia, 0, SWL, 660 SWL, Width between Straps
|
|
Home -> Sailboat -> Blocks->Series 20 Blocks
Two-stage bearing system with stainless-steel ball bearings handles very high safe working loads. Designed for small diameter, high-tech line on high-performance dinghies and control lines on sport and race boats. Each double and triple block offers a formed loop head and extra shackle for mounting versatility. Sheave: Acetal plastic. Sheave Size: 3/4" (20mm). Line Diameter: 1/4" max. Cheek Material/Finish: Stainless and textured fiber-reinforced Zytel.
Part No: RF20175
|
|
|
|
|
Home -> Sailboat -> Blocks->Series 20 Blocks
Two-stage bearing system with stainless-steel ball bearings handles very high safe working loads. Designed for small diameter, high-tech line on high-performance dinghies and control lines on sport and race boats. Each double and triple block offers a formed loop head and extra shackle for mounting versatility. Sheave: Acetal plastic. Sheave Size: 3/4" (20mm). Line Diameter: 1/4" max. Cheek Material/Finish: Stainless and textured fiber-reinforced Zytel.
Part No: RF20180
|
|
|
|
|
Home -> Sailboat -> Blocks->Series 20 Blocks
Two-stage bearing system with stainless-steel ball bearings handles very high safe working loads. Designed for small diameter, high-tech line on high-performance dinghies and control lines on sport and race boats. Each double and triple block offers a formed loop head and extra shackle for mounting versatility. Sheave: Acetal plastic. Sheave Size: 3/4" (20mm). Line Diameter: 1/4" max. Cheek Material/Finish: Stainless and textured fiber-reinforced Zytel.
Part No: RF20202
|
|
|
|
|
Home -> Sailboat -> Blocks->Series 20 Blocks
Two-stage bearing system with stainless-steel ball bearings handles very high safe working loads. Designed for small diameter, high-tech line on high-performance dinghies and control lines on sport and race boats. Each double and triple block offers a formed loop head and extra shackle for mounting versatility. Sheave: Acetal plastic. Sheave Size: 3/4" (20mm). Line Diameter: 1/4" max. Cheek Material/Finish: Stainless and textured fiber-reinforced Zytel.
Part No: RF20212
|
|
|
|
|
Home -> Sailboat -> Blocks->Series 20 Blocks
Two-stage bearing system with stainless-steel ball bearings handles very high safe working loads. Designed for small diameter, high-tech line on high-performance dinghies and control lines on sport and race boats. Each double and triple block offers a formed loop head and extra shackle for mounting versatility. Sheave: Acetal plastic. Sheave Size: 3/4" (20mm). Line Diameter: 1/4" max. Cheek Material/Finish: Stainless and textured fiber-reinforced Zytel.
Part No: RF20302
|
|
|
|
|
Home -> Sailboat -> Blocks->Series 20 Blocks
Two-stage bearing system with stainless-steel ball bearings handles very high safe working loads. Designed for small diameter, high-tech line on high-performance dinghies and control lines on sport and race boats. Each double and triple block offers a formed loop head and extra shackle for mounting versatility. Sheave: Acetal plastic. Sheave Size: 3/4" (20mm). Line Diameter: 1/4" max. Cheek Material/Finish: Stainless and textured fiber-reinforced Zytel.
Part No: RF20312
|
|
|
|
|
Home -> Sailboat -> Blocks->Series 20 Blocks
Two-stage bearing system with stainless-steel ball bearings handles very high safe working loads. Designed for small diameter, high-tech line on high-performance dinghies and control lines on sport and race boats. Each double and triple block offers a formed loop head and extra shackle for mounting versatility. Sheave: Acetal plastic. Sheave Size: 3/4" (20mm). Line Diameter: 1/4" max. Cheek Material/Finish: Stainless and textured fiber-reinforced Zytel.
Part No: RF20332
|
|
|
|
|
Home -> Sailboat -> Blocks->Series 20 Blocks
Two-stage bearing system with stainless-steel ball bearings handles very high safe working loads. Designed for small diameter, high-tech line on high-performance dinghies and control lines on sport and race boats. Each double and triple block offers a formed loop head and extra shackle for mounting versatility. Sheave: Acetal plastic. Sheave Size: 3/4" (20mm). Line Diameter: 1/4" max. Cheek Material/Finish: Stainless and textured fiber-reinforced Zytel.
Part No: RF20711
|
|
|
|
Home -> Sailboat -> Rigging Products->Stainless Sailmakers Thimbles
Sailmakers thimbles are completely enclosed and should be used anywhere a thimble is needed on running rigging to prevent chafe on the lines.
Part No: RF2180
|
|
|
|
|
Home -> Cordage -> Rigging Products->Stainless Sailmakers Thimbles
Sailmakers thimbles are completely enclosed and should be used anywhere a thimble is needed on running rigging to prevent chafe on the lines.
Part No: RF2181
|
|
|
|
|
Home -> Cordage -> Rigging Products->Stainless Sailmakers Thimbles
Sailmakers thimbles are completely enclosed and should be used anywhere a thimble is needed on running rigging to prevent chafe on the lines.
Part No: RF2182
|
|
|
|
|
Home -> Cordage -> Rigging Products->Stainless Sailmakers Thimbles
Sailmakers thimbles are completely enclosed and should be used anywhere a thimble is needed on running rigging to prevent chafe on the lines.
Part No: RF2183
|
|
|
|
|
Home -> Cordage -> Rigging Products->Stainless Sailmakers Thimbles
Sailmakers thimbles are completely enclosed and should be used anywhere a thimble is needed on running rigging to prevent chafe on the lines.
Part No: RF2184
|
|
|
|
Home -> Sailboat -> Rigging Products -> Shroud Covers, Mast Boots->Shroud Adjusters
The RF 2331 has a unique safety tab and pin retaining system that reduces the risk of losing the stay when adjusting the rig.
Part No: RF2330
|
|
|
|
|
Home -> Sailboat -> Rigging Products -> Shroud Covers, Mast Boots->Shroud Adjusters
The RF 2331 has a unique safety tab and pin retaining system that reduces the risk of losing the stay when adjusting the rig.
Part No: RF2331
|
|
|
|
Home -> Sailboat -> Blocks
Stand-Up base fits the head post of Series 50 blocks for added versatility. Diamond shape base measures 2" x 3" . Pin diameter: 3/16". MWL: 1100lb.
Part No: RF2450
|
|
|
|
Home -> Sailboat -> Blocks->Series 40 Orbit Block™ Accessories
Accessories to Ronstan Series 40 Orbit blocks.
Part No: RF2454
|
|
|
|
Home -> Sailboat -> Blocks -> Sheaves, Parts & Bases->Series 55 Orbit Block™ Accessories
The precision design provides the optimum number of ball bearings in critically loaded areas, eliminates them in inactive areas and reduces ineffective mass, creating the "2-stage" bearing system for durability and low friction performance. Sheave: Carbon-fiber reinforced, PTFE-impregnated engineered nylon. Bearings: High-compression–strength Carbon Black Acetal; Stage 2 Bearing: Glass fiber-reinforced, MoS2-impregnated engineered nylon. Sheave Size: 2-5/32" (55mm).
Part No: RF2455
|
|
|
|
Home -> Sailboat -> Blocks->Series 70 Orbit Block™ Accessories
Series 70 BB Ball Bearing & RT Ratchet Orbit Blocks™ With all the same high-strength, light weight features as the rest of the Orbit Blocks™ range, but designed to handle lines up to 1/2" diameter. Ideal for sheet applications on keelboats up to 30' and control lines on larger boats. Sheave: Carbon reinforced, PTFE impregnated engineered nylon. Ball Bearings: Series 70 BB Ball Bearing & RT Ratchet Orbit Blocks™. Sheave Size: 2-3/4" (70mm). : 1/2" (12mm).
Part No: RF2457
|
|
|
|
Home -> Sailboat -> Tiller & Rudder -> Rudder & Wheel Hdwr->Dinghy Pintles & Gudgeons
Strong, reinforced nylon fittings have compact profiles and minimal weight. Insert molded nylon bushings provide a firm fit between gudgeon and pintle, and prevent corrosion and fatigue. Constructed for precision performance and dependability. Hole dia.
Part No: RF2501
|
|
|
|
|
Home -> Sailboat -> Tiller & Rudder -> Rudder & Wheel Hdwr->Dinghy Pintles & Gudgeons
Strong, reinforced nylon fittings have compact profiles and minimal weight. Insert molded nylon bushings provide a firm fit between gudgeon and pintle, and prevent corrosion and fatigue. Constructed for precision performance and dependability. Hole dia.
Part No: RF2510
|
|
|
|
Home -> Sailboat -> Blocks -> Blocks
The incredible Series 20 Lashing Orbit Block™ is capable of loads up to 550lb. (250kg) while weighing a mere 0. (9 grams). It’s so light that it needs to be lashed down! Excellent choice for control lines on dinghies and catamarans up to 16'. 3/4" (20mm) high-compression-strength carbon Acetal sheave, stainless steel ball bearings and nylon frame/cheeks. Integrated stainless steel hub to accept lashing attachment and through-sheave becket. Fits up to 5/32" (4mm) lashing.
Part No: RF25109
|
|
|
|
|
Home -> Sailboat -> Tiller & Rudder -> Rudder & Wheel Hdwr->Dinghy Pintles & Gudgeons
Strong, reinforced nylon fittings have compact profiles and minimal weight. Insert molded nylon bushings provide a firm fit between gudgeon and pintle, and prevent corrosion and fatigue. Constructed for precision performance and dependability. Hole dia.
Part No: RF2515
|
|
|
|
Home -> Sailboat -> Blocks->Series 29 Utility Blocks
Stainless-steel cheeks and Acetal sheaves for light applications like dinghy vangs or outhauls or cunninghams and spinnaker controls on larger boats. Sheave: UV stabilized Acetal. Bearings: Plain bearings. Sheave Size: 1-1/8" (except RF341, 1"). Line Diameter: 5/16" max. (except RF341, 3/16" max. ). Cheek Material/Finish: Polished 316 Stainless.
Part No: RF280
|
|
|
|
|
Home -> Sailboat -> Blocks->Series 29 Utility Blocks
Stainless-steel cheeks and Acetal sheaves for light applications like dinghy vangs or outhauls or cunninghams and spinnaker controls on larger boats. Sheave: UV stabilized Acetal. Bearings: Plain bearings. Sheave Size: 1-1/8" (except RF341, 1"). Line Diameter: 5/16" max. (except RF341, 3/16" max. ). Cheek Material/Finish: Polished 316 Stainless.
Part No: RF285
|
|
|
|
Home -> Sailboat -> Shackles, Snaps & Fittings->Stainless-Steel Eye Straps
Eye straps are convenient for lashing points and attaching control line leads or blocks.
Part No: RF291
|
|
|
|
Home -> Engine Systems -> Horns/Wipers/Glove Boxes -> Drain Plugs
Mounts in a 15/16'' hole, and uses #10 FH fasteners.
Part No: RF294
|
|
|
|
Home -> Sailboat -> Headsail Furling
A sleek, snag-free way to lead your furler's lines back to the cockpit. Clamps around the 7/8" or 1" stanchion tubing, so you don't have to drill any holes.
Part No: RF3
|
|
|
|
Home -> Sailboat -> Downwind Poles & Cars -> Spinnaker Poles & Gear
Curved, diamond-shaped base mast pad eye fits masts with a 2 3/8" base radius. Ring measures 30mm (1 3/16") dia. 1/4" stainless rod. Weight: 1. 6oz.
Part No: RF30
|
|
|
|
Home -> Sailboat -> Blocks -> Blocks->Series 30 Ball-Bearing Mini Blocks
BLOCK,SER30 BB SGLE SLOT POST.
Part No: RF30100A
|
|
|
